
[Federal Register Volume 78, Number 123 (Wednesday, June 26, 2013)]
[Notices]
[Pages 38389-38409]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2013-15228]


-----------------------------------------------------------------------

DEPARTMENT OF LABOR

Occupational Safety and Health Administration

[Docket No. OSHA-2013-0012]


Proposed Modification to the Scopes of Recognition of Several 
NRTLs

AGENCY: Occupational Safety and Health Administration (OSHA), Labor.

ACTION: Notice.

-----------------------------------------------------------------------

SUMMARY: In this notice, OSHA proposes to delete several test standards 
from the scopes of recognition of several nationally recognized testing 
laboratories (NRTLs), and to incorporate into the scopes of recognition 
of several NRTLs test standards to replace some of the deleted test 
standards.

DATES: Submit comments, information, and documents in response to this 
notice, or requests for an extension of time to make a submission, on 
or before July 26, 2013. All submissions must bear a postmark or 
provide other evidence of the submission date.

ADDRESSES:

[[Page 38390]]

    Electronically: Tender submissions electronically to the Federal 
eRulemaking Portal at http://www.regulations.gov. Follow the 
instructions online for making electronic submissions.
    Facsimile: If submissions, including attachments, are not longer 
than ten (10) pages, commenters may fax them to the OSHA Docket Office 
at (202) 693-1648.
    Regular or Express Mail, Hand Delivery, or Messenger (Courier) 
Service: Tender submissions to the OSHA Docket Office, Docket No. OSHA-
2013-0012, Technical Data Center, Room N-2625, U.S. Department of 
Labor, 200 Constitution Avenue NW., Washington, DC 20210; telephone: 
(202) 693-2350 (TTY number: (877) 889-5627). Note that security 
procedures may result in significant delays in receiving submissions 
sent by regular mail. Contact the OSHA Docket Office for information 
about security procedures concerning delivery of materials by regular 
or express mail, hand delivery, or messenger (courier) service. The 
hours of operation for the OSHA Docket Office are 8:15 a.m.-4:45 p.m., 
e.t.
    Instructions: All submissions must include the Agency name and the 
OSHA docket number (OSHA-2013-0012). OSHA places comments and other 
materials, including any personal information, in the public docket 
without revision, and these materials may be available online at http://www.regulations.gov. Therefore, the Agency cautions commenters about 
submitting statements they do not want made available to the public, or 
submitting comments that contain personal information (either about 
themselves or others) such as Social Security numbers, birth dates, and 
medical data.
    Docket: To read or download submissions or other material in the 
docket, go to http://www.regulations.gov or to the OSHA Docket Office 
at the address above. The http://www.regulations.gov index lists all 
documents in the docket; however, some information (e.g., copyrighted 
material) is not publicly available to read or download through this 
Web site. All documents in the docket, including copyrighted material, 
are available for inspection at the OSHA Docket Office.

FOR FURTHER INFORMATION CONTACT: Information regarding this notice is 
available from the following sources:
    Press Inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office 
of Communications, Room N-3647, U.S. Department of Labor, 200 
Constitution Avenue NW., Washington, DC 20210; telephone: (202) 693-
1999; email: Meilinger.francis2@dol.gov.
    General and Technical Information: Contact Mr. David Johnson, NRTL 
Program, Occupational Safety and Health Administration, Room N-3655, 
U.S. Department of Labor, 200 Constitution Avenue NW., Washington, DC 
20210; telephone (202) 693-2110. OSHA's Web page includes information 
about the NRTL Program (see http://www.osha.gov and select ``N'' in the 
``A to Z Index'' located at the top of the Web page).
    Copies of this Federal Register Notice: Electronic copies of this 
Federal Register notice are available at http://www.regulations.gov. 
This Federal Register notice, as well as other relevant information, is 
also available on OSHA's Web page at http://www.osha.gov.

SUPPLEMENTARY INFORMATION:

I. Background

    The NRTL Program recognizes organizations that provide product-
safety testing and certification services to manufacturers. These 
organizations perform testing and certification, for purposes of the 
Program, to U.S. consensus-based product-safety test standards. OSHA 
does not develop or issue these test standards, but generally relies on 
U.S. standards-development organizations (SDOs) accredited by the 
American National Standards Institute (ANSI). The products covered by 
the Program consist of those items for which OSHA safety standards 
require ``certification'' by an NRTL. The requirements affect 
electrical products and 38 other types of products.
    OSHA recognition of an organization as an NRTL signifies that the 
organization meets the legal requirements in the NRTL Program 
regulations at 29 CFR 1910.7 and the NRTL Program policies in CPL 1-0.3 
NRTL Program Policies, Procedures, and Guidelines (``Directive''). 
Recognition is an acknowledgement by OSHA that the NRTL can perform 
independent safety testing and certification of the specific products 
covered within the NRTL's scope of recognition. Recognition of an NRTL 
by OSHA also allows employers to use products certified by that NRTL to 
meet those OSHA standards that require product testing and 
certification (29 CFR 1910.7(a)).
    An NRTL's scope of recognition consists, in part, of the specific 
test standard(s) approved by OSHA for use by the NRTL. Pursuant to the 
NRTL Program regulations, the NRTL must first request to have a test 
standard included in its scope of recognition. OSHA will grant the 
NRTL's request only if the NRTL has the capability to test and examine 
equipment \1\ and materials for workplace safety purposes and to 
determine conformance with the test standard for each relevant item of 
equipment or material that it lists, labels, or accepts (29 CFR 
1910.7(b)(1)). Capability includes proper testing equipment and 
facilities, trained staff, written testing procedures, and calibration 
and quality-control programs. An organization's recognition as an NRTL 
is, therefore, not for products, but for ``appropriate'' test standards 
covering a type of product(s) (29 CFR 1910.7(b)(1)).
---------------------------------------------------------------------------

    \1\ In this notice, OSHA uses the terms ``equipment'' and 
``product'' or ``products'' interchangeably.
---------------------------------------------------------------------------

    Pursuant to the NRTL Program regulations, to be ``appropriate,'' a 
test standard must be current, and it must specify the safety 
requirements for a specific type of product(s) (29 CFR 1910.7(c)). OSHA 
policy provides that a document specifies safety requirements for a 
specific type product(s) if the document includes ``features, parts, 
capabilities, usage limitations, or installation requirements which if 
they did not exist would create a potential hazard in using the 
equipment'' (Directive, App. D.IV.B). However, OSHA policy also 
provides that the document not ``focus primarily on usage, 
installation, or maintenance requirements'' (Directive, App. D.IV.B). 
Finally, as OSHA requires the testing and certification of certain 
products only (29 CFR 1910.7(a)), an NRTL's scope of recognition should 
not include test standards that do not specify safety requirements for 
products for which OSHA does not require testing and certification 
(Directive, App. D.IV.A).

II. Modifying Test Standards in NRTLs' Scopes of Recognition

A. Proposed Deletion of Withdrawn Test Standards From, and 
Incorporation of Replacement Test Standards Into, the Scopes of 
Recognition of Several NRTLs

    In this notice, OSHA proposes to delete several withdrawn test 
standards from the scopes of recognition of several NRTLs. OSHA also 
proposes to incorporate into the scopes of recognition of several NRTLs 
test standards to replace some of the withdrawn (and deleted) test 
standards.
    The NRTL Program regulations require that appropriate test 
standards be current (29 CFR 1910.7(c)). A test standard withdrawn by a 
standards organization is no longer considered an appropriate test 
standard (Directive, App. C.XIV.B). It is OSHA's policy to remove 
recognition of withdrawn test standards by issuing a correction notice

[[Page 38391]]

in the Federal Register for all NRTLs recognized for the withdrawn test 
standards. However, OSHA will recognize an NRTL for an appropriate 
replacement test standard if the NRTL has the requisite testing and 
evaluation capability for the replacement test standard.
    One method that NRTLs may use to show such capability involves an 
analysis to determine whether any testing and evaluation requirements 
of existing test standards in an NRTL's scope are comparable (i.e., are 
completely or substantially identical) to the requirements in the 
replacement test standard. If OSHA's analysis shows the replacement 
test standard does not require additional or different technical 
capability than an existing test standard(s), the replacement test 
standard is comparable to the existing test standard(s), and OSHA can 
add the replacement test standard to affected NRTLs' scopes of 
recognition. In making this determination, OSHA also considers the 
documents or medium that the NRTL uses to record test and evaluation 
data or results, which OSHA commonly calls ``test datasheets,'' to be 
part of the NRTL's written testing procedures.\2\
---------------------------------------------------------------------------

    \2\ Such datasheets may be electronic records or hardcopies, and 
must ensure that the NRTL will capture all necessary test and 
evaluation data or results completely and accurately. Additionally, 
datasheets may be separate or combined in other documents or 
records.
---------------------------------------------------------------------------

    If OSHA's analysis shows the replacement test standard requires an 
additional or different technical capability, the replacement test 
standard is not comparable to any existing test standards. Furthermore, 
if a replacement test standard requires the NRTL to modify its 
datasheets substantively, or to develop new datasheets, then the test 
standards are also not comparable. In such cases (i.e., when the test 
standards are not comparable), each affected NRTL that seeks to have 
OSHA add the replacement test standard to the NRTL's scope of 
recognition must provide information to OSHA that demonstrates 
technical capability.

B. Proposed Deletion of Inappropriate Test Standards From the Scopes of 
Recognition of Several NRTLs

    OSHA proposes to delete several test standards from the scopes of 
recognition of several NRTLs based on a recent internal review in which 
NRTL Program staff determined that several test standards currently in 
the NRTLs' scopes of recognition did not conform to the definition of 
appropriate test standard defined in NRTL Program regulations and 
policy. First, one of the documents at issue, UL 1666, provides the 
methodology for one test only, and is, therefore, a test method rather 
than an appropriate test standard (29 CFR 1910.7(c)). As stated above, 
a test standard must specify the safety requirements for a specific 
type of product(s). Id. A test method, however, is a ``specified 
technical procedure for performing a test'' (Directive, App. B). As 
such, a test method is not an appropriate test standard: While an NRTL 
may use a test method to determine if certain safety requirements are 
met, a test method is not itself a safety requirement for a specific 
product.
    Second, several of the documents focus primarily on usage, 
installation, or maintenance requirements. As stated above, such 
documents are not appropriate test standards (Directive, App. D.IV.B).
    Third, some of the documents are not appropriate test standards 
because the documents cover products for which OSHA does not require 
testing and certification (Directive, App. D.IV.A). OSHA initially 
recognized these documents for use in the NRTL Program under OSHA 
standards such as 29 CFR 1910.68. These OSHA standards do not require 
testing and certification for the product(s) covered by the documents 
OSHA proposes to delete.
    Finally, several of the documents cover electrical-product 
components, such as transformers, resistors, and capacitors used in 
television-type appliances. These documents apply to types of 
components that have limitation(s) or condition(s) on their use, in 
that they are not appropriate for use as end-use products. These 
documents also specify that these types of components are for use only 
as part of an end-use product. NRTLs, however, evaluate such components 
only in the context of evaluating whether end-use products requiring 
NRTL approval are safe for use in the workplace. Testing such 
components alone would not indicate that the end-use products 
containing the components are safe for use. Accordingly, as a matter of 
policy, OSHA considers that documents covering such components are not 
appropriate test standards under the NRTL Program. OSHA notes, however, 
that it is not proposing to delete from NRTLs' scopes of recognition 
any test standards covering end-use products that contain such 
components.\3\
---------------------------------------------------------------------------

    \3\ OSHA notes also that some types of devices covered by these 
documents, such as capacitors and transformers, may be end-use 
products themselves, and tested under other test standards 
applicable to such products. For example, the following test 
standard covers transformers that are end-use products: UL 1562 
Standard for Transformers, Distribution, Dry-Type--Over 600 Volts. 
OSHA is not proposing to delete such test standards from NRTLs' 
scopes of recognition.
---------------------------------------------------------------------------

    In addition, OSHA notes that, to conform to a test standard 
covering an end-use product, an NRTL must still determine that the 
components in the product comply with these components' specific test 
standards, some of which OSHA is proposing to delete in this notice. In 
making this determination, NRTLs may test the components themselves, or 
accept the testing of a qualified testing organization that a given 
component conforms to its particular test standard. OSHA reviews each 
NRTL's procedures to determine which approach the NRTL will use to 
address components, and reviews the end-use product testing to verify 
the NRTL appropriately addresses that product's components.
    OSHA added the documents now subject to deletion to affected NRTLs' 
scopes of recognition before OSHA issued the NRTL Program Directive. 
The Directive clarified the meaning of ``appropriate test standard.'' 
After issuing the Directive, OSHA deleted some documents from NRTLs' 
scopes of recognition because those documents were not appropriate test 
standards (see 70 FR 11273, March 8, 2005). After further review of the 
entire list of test standards recognized under the NRTL Program, OSHA 
determined that it should delete additional documents from NRTLs' 
scopes of recognition. In all cases, these deletions would be 
programmatic corrections only, and do not reflect OSHA's view of the 
technical merits of the documents. In addition, deleting these 
documents from the NRTLs' scopes of recognition would not prevent 
testing organizations (including NRTLs) from using the deleted 
documents for their testing activities.

III. Test Standards OSHA Proposes To Delete and Incorporate

    Table 1 lists the test standards that OSHA proposes to delete from 
affected NRTLs' scopes of recognition, as well as an abbreviated 
rationale for OSHA's proposed actions. For a full discussion of the 
rationale, see, above, Sections II.A and II.B of this notice. Table 1 
also lists corresponding replacement test standards that OSHA proposes 
to incorporate into the NRTLs' scopes of recognition (when applicable).
    In most cases, OSHA already incorporated the proposed replacement 
test standards into affected NRTLs' scopes of recognition. OSHA 
proposes

[[Page 38392]]

one of the following actions with respect to the remaining cases:
    1. OSHA proposes to incorporate, for all affected NRTLs, comparable 
test standards that SDOs adopted to replace withdrawn (and deleted) 
test standards; or
    2. OSHA proposes to incorporate, for all affected NRTLs, 
appropriate test standards that OSHA concludes are comparable to the 
withdrawn (and deleted) test standards.
    OSHA notes that it is not proposing to delete UL 664 from the 
scopes of recognition of affected NRTLs, even though Underwriters 
Laboratories withdrew UL 664. OSHA currently is examining whether it 
can incorporate any test standard(s) into the scopes of recognition of 
affected NRTLs to replace UL 664. Once OSHA completes this examination, 
it will issue a new Federal Register notice addressing the deletion of 
UL 664 from the scopes of recognition of affected NRTLs.
    OSHA also notes that it is not proposing to delete UL 1004 from the 
scopes of recognition of affected NRTLs even though Underwriters 
Laboratories withdrew UL 1004, and issued UL 1004-1 as a replacement. 
Unlike other replacements shown in this notice, OSHA believes that UL 
1004-1 is not comparable to UL 1004. OSHA currently is working on a 
separate Federal Register notice that will propose how OSHA plans to 
incorporate such test standard(s), and a number of other test 
standards, into the scopes of recognition of affected NRTLs. OSHA plans 
to publish this notice in the near future.
    OSHA notes also that Table 1 lists the subject test standards and 
the proposed action with regard to each of these test standards without 
indicating how the proposed action will affect individual NRTLs. 
Section IV of this notice discusses how the proposed action will affect 
individual NRTLs.

     Table 1--List of Test Standards OSHA Proposes To Delete From or
               Incorporate Into NRTL Scopes of Recognition
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed  test standard(s) (if
          standard                  deletion             applicable)
------------------------------------------------------------------------
ANSI A90.1 Safety Standard    29 CFR 1910.68 does   Not applicable (NA).
 for Belt Manlifts.            not require testing
                               and certification
                               for covered
                               product(s); also
                               not an appropriate
                               test standard
                               because it covers
                               primarily the
                               manufacture,
                               installation,
                               maintenance,
                               inspection, and
                               operation of
                               manlifts, not
                               safety testing.
ASTM E2074 Standard Test      Withdrawn...........  No replacement.
 Method for Fire Tests of
 Door Assemblies, Including
 Positive Pressure Testing
 of Side-Hinged and Pivoted
 Swinging Door Assemblies.
ANSI/NFPA 11A Medium- and     Withdrawn; moreover,  NA. Although
 High-Expansion Foam Systems.  OSHA standards do     replaced by ANSI/
                               not require testing   NFPA 11, ANSI/NFPA
                               and certification     11 is not an
                               for covered systems.  appropriate test
                                                     standard (see 75 FR
                                                     77002, 77004-77005,
                                                     Dec. 10, 2010, for
                                                     discussion of why
                                                     ANSI/NFPA 11 is not
                                                     appropriate).
ANSI/NFPA 20 Installation of  Not an appropriate    NA.
 Stationary Fire Pumps for     test standard
 Fire Protection.              because it covers
                               primarily the
                               selection and
                               installation of
                               these pumps, not
                               safety testing.
UL 94 Tests for Flammability  No requirement for    NA.
 of Plastic Materials for      NRTL approval
 Parts in Devices and          because the
 Appliances.                   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 187 X Ray Equipment......  Withdrawn...........  UL 60601-1 Medical
                                                     Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 1
                                                     below).
UL 207 Refrigerant-           No requirement for    NA.
 Containing Components and     NRTL approval
 Accessories, Nonelectrical.   because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 343 Pumps for Oil-Burning  No requirement for    NA.
 Appliances.                   NRTL approval of
                               this type of pump.
UL 512 Fuseholders..........  Withdrawn...........  UL 4248-1
                                                     Fuseholders--Part
                                                     1: General
                                                     Requirements.
                                                    UL 4248-4
                                                     Fuseholders--Part
                                                     4: Class CC.
                                                    UL 4248-5
                                                     Fuseholders--Part
                                                     5: Class G.
                                                    UL 4248-6
                                                     Fuseholders--Part
                                                     6: Class H.
                                                    UL 4248-8
                                                     Fuseholders--Part
                                                     8: Class J.
                                                    UL 4248-9
                                                     Fuseholders--Part
                                                     9: Class K.
                                                    UL 4248-11
                                                     Fuseholders--Part
                                                     11: Type C (Edison
                                                     Base) and Type S
                                                     Plug Fuse.
                                                    UL 4248-12
                                                     Fuseholders--Part
                                                     12: Class R.
                                                    UL 4248-15
                                                     Fuseholders--Part
                                                     15: Class T (for
                                                     all replacement
                                                     standards, see Note
                                                     1 below).
UL 544 Medical and Dental     Withdrawn...........  UL 60601-1 Medical
 Equipment.                                          Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 1
                                                     below).
UL 632 Electrically-Actuated  Withdrawn...........  No replacement.
 Transmitters.
UL 651B Continuous Length     Withdrawn...........  UL 651A Schedule 40
 HDPE Conduit.                                       and 80 High Density
                                                     Polyethylene (HDPE)
                                                     Conduit (see Note 1
                                                     below).

[[Page 38393]]

 
UL 698 Industrial Control     Withdrawn...........  UL 1203 Explosion
 Equipment for Use in                                Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     1 below).
UL 745-2-2 Particular         Withdrawn...........  UL 60745-2-2 Hand-
 Requirements for                                    Held Motor-Operated
 Screwdrivers and Impact                             Electric Tools--
 Wrenches.                                           Safety--Part 2-2:
                                                     Particular
                                                     Requirements for
                                                     Screwdrivers and
                                                     Impact Wrenches
                                                     (see Note 1 below).
UL 745-2-4 Particular         Withdrawn...........  UL 60745-2-4 Hand-
 Requirements for Sanders.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-4:
                                                     Particular
                                                     Requirements for
                                                     Sanders and
                                                     Polishers Other
                                                     Than Disk Type (see
                                                     Note 1 below).
UL 745-2-6 Particular         Withdrawn...........  UL 60745-2-6 Hand-
 Requirements for Hammers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-6:
                                                     Particular
                                                     Requirements for
                                                     Hammers (see Note 1
                                                     below).
UL 745-2-8 Particular         Withdrawn...........  UL 60745-2-8 Hand-
 Requirements for Shears and                         Held Motor-Operated
 Nibblers.                                           Electric Tools
                                                     Safety--Part 2-8:
                                                     Particular
                                                     Requirements for
                                                     Shears and Nibblers
                                                     (see Note 1 below).
UL 745-2-9 Particular         Withdrawn...........  UL 60745-2-9 Hand-
 Requirements for Tappers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-9:
                                                     Particular
                                                     Requirements for
                                                     Tappers (see Note 1
                                                     below).
UL 745-2-11 Particular        Withdrawn...........  UL 60745-2-11 Hand-
 Requirements for                                    Held Motor-Operated
 Reciprocating Saws.                                 Electric Tools--
                                                     Safety--Part 2-11:
                                                     Particular
                                                     Requirements for
                                                     Reciprocating Saws
                                                     (see Note 1 below).
UL 745-2-12 Particular        Withdrawn...........  UL 60745-2-12 Hand-
 Requirements for Concrete                           Held Motor-Operated
 Vibrators.                                          Electric Tools--
                                                     Safety--Part 2-12:
                                                     Particular
                                                     Requirements For
                                                     Concrete Vibrators
                                                     (see Note 1 below).
UL 745-2-30 Particular        Withdrawn...........  UL 60745-2-16 Hand-
 Requirements for Staplers.                          Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-16:
                                                     Particular
                                                     Requirements for
                                                     Tackers (see Note 1
                                                     below).
UL 745-2-33 Particular        Withdrawn...........  UL 60745-2-20 Hand-
 Requirements for Portable                           Held Motor-Operated
 Bandsaw.                                            Electric Tools--
                                                     Safety--Part 2-20:
                                                     Particular
                                                     Requirements For
                                                     Band Saws (see Note
                                                     1 below).
UL 745-2-34 Particular        Withdrawn...........  UL 60745-2-18 Hand-
 Requirements for Strapping                          Held Motor-Operated
 Tools.                                              Electric Tools--
                                                     Safety--Part 2-18:
                                                     Particular
                                                     Requirements For
                                                     Strapping Tools
                                                     (see Note 1 below).
UL 746A Polymeric Materials   No requirement for    NA.
 Short Term Property           NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746B Polymeric Materials   No requirement for    NA.
 Long Term Property            NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746C Polymeric Materials-- No requirement for    NA.
 Use in Electrical Equipment   NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746E Polymeric Materials-- No requirement for    NA.
 Industrial Laminates,         NRTL approval
 Filament Wound Tubing,        because the
 Vulcanized Fibre, and         standard covers
 Materials Used in Printed-    components that are
 Wiring Boards.                not appropriate for
                               use as end-use
                               products.
UL 781 Portable Electric      Withdrawn...........  UL 844 Electric
 Lighting Units for Use in                           Lighting Fixtures
 Hazardous (Classified)                              for Use in
 Locations.                                          Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     1 below).
UL 796 Printed[dash]Wiring    No requirement for    NA.
 Boards.                       NRTL approval
                               because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 877 Circuit Breakers and   Withdrawn...........  UL 1203 Explosion
 Circuit Breaker Enclosures                          Proof and Dust
 for Use in Hazardous                                Ignition Proof
 (Classified) Locations (UL                          Electrical
 1203).                                              Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     1 below).

[[Page 38394]]

 
UL 886 Outlet Boxes and       Withdrawn...........  UL 1203 Explosion
 Fittings for Use in                                 Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     1 below).
UL 894 Switches for Use in    Withdrawn...........  UL 1203 Explosion
 Hazardous (Classified)                              Proof and Dust
 Locations.                                          Ignition Proof
                                                     Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     1 below).
UL 983 Surveillance Camera    Withdrawn...........  No replacement.
 Units.
UL 1002 Electrically          Withdrawn...........  UL 1203 Explosion
 Operated Valves for Use in                          Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     1 below).
UL 1005 Electric Flatirons..  Withdrawn...........  UL 60335-2-3
                                                     Household and
                                                     Similar Electrical
                                                     Appliances, Part 2:
                                                     Particular
                                                     Requirements for
                                                     Electric Irons (see
                                                     Note 1 below).
UL 1010 Receptacle Plug       Withdrawn...........  UL 1203 Explosion
 Combinations for Use in                             Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     1 below).
UL 1075 Gas-Fired Cooking     Withdrawn...........  No replacement.
 Appliances for Recreational
 Vehicles.
UL 1097 Double Insulation     No requirement for    NA.
 Systems for Use in            NRTL approval
 Electrical Equipment.         because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1411 Transformers and      No requirement for    NA.
 Motor Transformers for Use    NRTL approval
 In Audio-, Radio-, and        because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1412 Fusing Resistors and  No requirement for    NA.
 Temperature-Limited           NRTL approval
 Resistors for Radio-, and     because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1413 High Voltage          No requirement for    NA.
 Components for Television     NRTL approval
 Type Appliances.              because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1414 Across-the-Line,      No requirement for    NA.
 Antenna-Coupling, and Line-   NRTL approval
 by-Pass Capacitors for        because the
 Radio- and Television-Type    standard covers
 Appliances.                   components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1416 Overcurrent and       No requirement for    NA.
 Overtemperature Protectors    NRTL approval
 for Radio- and Television-    because the
 Type Appliances.              standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1417 Special Fuses for     No requirement for    NA.
 Radio- and Television-Type    NRTL approval
 Appliances.                   because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1433 Control Centers for   Withdrawn...........  No replacement.
 Changing Message Type
 Electric Signs.
UL 1445 Electric Water Bed    Withdrawn...........  No replacement.
 Heaters.
UL 1604 Electrical Equipment  Withdrawn...........  ANSI/ISA-12.12.01
 for Use in Class I and II,                          Nonincendive
 Division 2 and Class III                            Electrical
 Hazardous (Classified)                              Equipment for Use
 Locations.                                          in Class I and II,
                                                     Division 2 and
                                                     Class III,
                                                     Divisions 1 and 2
                                                     Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     1 below).
UL 1664 Immersion Detection   Withdrawn...........  No replacement.
 Circuit Interrupters.
UL 1666 Test for Flame        Test method;          NA.
 Propagation Height of         therefore, not an
 Electrical and Optical        appropriate test
 Fiber Cables Installed        standard.
 Vertically in Shafts.
UL 1684 Reinforced            Withdrawn...........  UL 2420 Belowground
 Thermosetting Resin Conduit                         Reinforced
 (RTRC) and Fittings.                                Thermosetting Resin
                                                     Conduit (RTRC) and
                                                     Fittings and UL
                                                     2515 Aboveground
                                                     Reinforced
                                                     Thermosetting Resin
                                                     Conduit (RTRC) and
                                                     Fittings (for both
                                                     replacement
                                                     standards, see Note
                                                     1 below).
UL 1686 Pin and Sleeve        Not an appropriate    NA.
 Configurations.               test standard; does
                               not specify safety
                               requirements for
                               covered devices;
                               provides the
                               physical dimensions
                               for covered devices
                               only.
UL 1692 Polymeric Materials   No requirement for    NA.
 Coil Forms.                   NRTL approval
                               because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.

[[Page 38395]]

 
UL 1694 Tests for             No requirement for    NA.
 Flammability of Small         NRTL approval
 Polymeric Component           because the
 Materials).                   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 2106 Field Erected Boiler  No requirement for    NA.
 Assemblies.                   NRTL approval in
                               OSHA requirements;
                               test standard
                               applies to boilers
                               burning fuel.
UL 60691 Thermal Links        No requirement for    NA.
 Requirements and              NRTL approval
 Application Guide.            because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
------------------------------------------------------------------------


    Note 1:  OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Therefore, OSHA proposes 
to incorporate the replacement test standard into affected NRTLs' 
scopes of recognition without requiring affected NRTLs to further 
demonstrate capability, as specified by 29 CFR 1910.7(b)(1). OSHA 
notes that such proposed action is not necessary for those NRTLs 
with scopes of recognition that already include the proposed 
replacement test standard.

IV. Proposed Modifications to Affected NRTLs' Scopes of Recognition

    The tables in this section (Table 2 thru Table 13) list, for each 
affected NRTL, the test standard(s) that OSHA proposes to delete from 
the scope of recognition of the NRTL and, when applicable, the test 
standard(s) that OSHA proposes to incorporate into the scope of 
recognition of that NRTL to replace withdrawn (and deleted) test 
standards. Notes to the tables make clear whether individual NRTLs must 
submit information to demonstrate their capability for each proposed 
replacement test standard.
    OSHA seeks the following input on whether the actions OSHA proposes 
in the tables are appropriate:
    1. OSHA seeks comment on whether its proposed deletions and 
incorporations are appropriate, and whether individual tables omit any 
appropriate replacement test standard that is comparable to a withdrawn 
test standard. If OSHA determines that it omitted any appropriate 
replacement test standard that is comparable to a withdrawn test 
standard, it will, in its final determination, incorporate that 
replacement test standard into the scope of recognition of each 
affected NRTL.
    2. In addition, the test standards listed in the tables include 
only withdrawn or otherwise inappropriate standards of which OSHA 
became aware on or before May 1, 2013. OSHA seeks input on whether 
individual NRTLs' scopes of recognition contain any additional 
withdrawn or otherwise inappropriate test standards.
    OSHA will incorporate into its informational Web pages the 
modifications OSHA decides to make to each NRTL's scope of recognition. 
These Web pages detail the scope of recognition for each NRTL, 
including the test standards the NRTL may use to test and certify 
products under OSHA's NRTL Program. OSHA also will add, to its 
``Composite List of Standards Recognized under the NRTL Program'' Web 
page, those test standards it incorporates into affected NRTLs' scopes 
of recognition, and add, to its ``Composite List of Test Standards No 
Longer Recognized'' Web page, those test standards that OSHA no longer 
recognizes or permits under the NRTL Program. Access to these Web pages 
is available at http://www.osha.gov/dts/otpca/nrtl/index.html.
    OSHA proposes the following revisions to the scopes of recognition 
of individual NRTLs:

Table 2--Test Standards OSHA Proposes To Delete From or Incorporate Into
  the Scope of Recognition of the Canadian Standards Association (CSA)
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed  test standard(s) (if
          standard                  deletion             applicable)
------------------------------------------------------------------------
UL 94 Tests for Flammability  No requirement for    NA.
 of Plastic Materials for      NRTL approval
 Parts in Devices and          because the
 Appliances.                   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 187 X Ray Equipment......  Withdrawn...........  UL 60601-1 Medical
                                                     Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 2
                                                     below).
UL 207 Refrigerant-           No requirement for    NA.
 Containing Components and     NRTL approval
 Accessories, Nonelectrical.   because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 343 Pumps for Oil-Burning  No requirement for    NA.
 Appliances.                   NRTL approval of
                               this type of pump.
UL 512 Fuseholders..........  Withdrawn...........  UL 4248-1
                                                     Fuseholders--Part
                                                     1: General
                                                     Requirements.
                                                    UL 4248-4
                                                     Fuseholders--Part
                                                     4: Class CC.
                                                    UL 4248-5
                                                     Fuseholders--Part
                                                     5: Class G.
                                                    UL 4248-6
                                                     Fuseholders--Part
                                                     6: Class H.
                                                    UL 4248-8
                                                     Fuseholders--Part
                                                     8: Class J.
                                                    UL 4248-9
                                                     Fuseholders--Part
                                                     9: Class K.
                                                    UL 4248-11
                                                     Fuseholders--Part
                                                     11: Type C (Edison
                                                     Base) and Type S
                                                     Plug Fuse.
                                                    UL 4248-12
                                                     Fuseholders--Part
                                                     12: Class R.

[[Page 38396]]

 
                                                    UL 4248-15
                                                     Fuseholders--Part
                                                     15: Class T (for
                                                     all replacement
                                                     standards, see Note
                                                     3 below).
UL 544 Medical and Dental     Withdrawn...........  UL 60601-1 Medical
 Equipment.                                          Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 2
                                                     below).
UL 632 Electrically-Actuated  Withdrawn...........  No replacement.
 Transmitters.
UL 651B Continuous Length     Withdrawn...........  UL 651A Schedule 40
 HDPE Conduit.                                       and 80 High Density
                                                     Polyethylene (HDPE)
                                                     Conduit (see Note 2
                                                     below).
UL 698 Industrial Control     Withdrawn...........  UL 1203 Explosion
 Equipment for Use in                                Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 745-2-2 Particular         Withdrawn...........  UL 60745-2-2 Hand-
 Requirements for                                    Held Motor-Operated
 Screwdrivers and Impact                             Electric Tools--
 Wrenches.                                           Safety--Part 2-2:
                                                     Particular
                                                     Requirements for
                                                     Screwdrivers and
                                                     Impact Wrenches
                                                     (see Note 3 below).
UL 745-2-4 Particular         Withdrawn...........  UL 60745-2-4 Hand-
 Requirements for Sanders.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-4:
                                                     Particular
                                                     Requirements for
                                                     Sanders and
                                                     Polishers Other
                                                     Than Disk Type (see
                                                     Note 3 below).
UL 745-2-6 Particular         Withdrawn...........  UL 60745-2-6 Hand-
 Requirements for Hammers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-6:
                                                     Particular
                                                     Requirements for
                                                     Hammers (see Note 3
                                                     below).
UL 745-2-8 Particular         Withdrawn...........  UL 60745-2-8 Hand-
 Requirements for Shears and                         Held Motor-Operated
 Nibblers.                                           Electric Tools
                                                     Safety--Part 2-8:
                                                     Particular
                                                     Requirements for
                                                     Shears and Nibblers
                                                     (see Note 3 below).
UL 745-2-9 Particular         Withdrawn...........  UL 60745-2-9 Hand-
 Requirements for Tappers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-9:
                                                     Particular
                                                     Requirements for
                                                     Tappers (see Note 3
                                                     below).
UL 745-2-11 Particular        Withdrawn...........  UL 60745-2-11 Hand-
 Requirements for                                    Held Motor-Operated
 Reciprocating Saws.                                 Electric Tools--
                                                     Safety--Part 2-11:
                                                     Particular
                                                     Requirements for
                                                     Reciprocating Saws
                                                     (see Note 3 below).
UL 745-2-12 Particular        Withdrawn...........  UL 60745-2-12 Hand-
 Requirements for Concrete                           Held Motor-Operated
 Vibrators.                                          Electric Tools--
                                                     Safety--Part 2-12:
                                                     Particular
                                                     Requirements For
                                                     Concrete Vibrators
                                                     (see Note 3 below).
UL 745-2-30 Particular        Withdrawn...........  UL 60745-2-16 Hand-
 Requirements for Staplers.                          Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-16:
                                                     Particular
                                                     Requirements for
                                                     Tackers (see Note 3
                                                     below).
UL 745-2-33 Particular        Withdrawn...........  UL 60745-2-20 Hand-
 Requirements for Portable                           Held Motor-Operated
 Bandsaw.                                            Electric Tools--
                                                     Safety--Part 2-20:
                                                     Particular
                                                     Requirements For
                                                     Band Saws (see Note
                                                     3 below).
UL 745-2-34 Particular        Withdrawn...........  UL 60745-2-18 Hand-
 Requirements for Strapping                          Held Motor-Operated
 Tools.                                              Electric Tools--
                                                     Safety--Part 2-18:
                                                     Particular
                                                     Requirements For
                                                     Strapping Tools
                                                     (see Note 3 below).
UL 746A Polymeric Materials   No requirement for    NA.
 Short Term Property           NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746B Polymeric Materials   No requirement for    NA.
 Long Term Property            NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746C Polymeric Materials-- No requirement for    NA.
 Use in Electrical Equipment   NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746E Polymeric Materials-- No requirement for    NA.
 Industrial Laminates,         NRTL approval
 Filament Wound Tubing,        because the
 Vulcanized Fibre, and         standard covers
 Materials Used in Printed-    components that are
 Wiring Boards.                not appropriate for
                               use as end-use
                               products.

[[Page 38397]]

 
UL 781 Portable Electric      Withdrawn...........  UL 844 Electric
 Lighting Units for Use in                           Lighting Fixtures
 Hazardous (Classified)                              for Use in
 Locations.                                          Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 796 Printed[dash]Wiring    No requirement for    NA.
 Boards.                       NRTL approval
                               because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 877 Circuit Breakers and   Withdrawn...........  UL 1203 Explosion
 Circuit Breaker Enclosures                          Proof and Dust
 for Use in Hazardous                                Ignition Proof
 (Classified) Locations (UL                          Electrical
 1203).                                              Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 886 Outlet Boxes and       Withdrawn...........  UL 1203 Explosion
 Fittings for Use in                                 Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 894 Switches for Use in    Withdrawn...........  UL 1203 Explosion
 Hazardous (Classified)                              Proof and Dust
 Locations.                                          Ignition Proof
                                                     Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 983 Surveillance Camera    Withdrawn...........  No replacement.
 Units.
UL 1002 Electrically          Withdrawn...........  UL 1203 Explosion
 Operated Valves for Use in                          Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 1005 Electric Flatirons..  Withdrawn...........  UL 60335-2-3
                                                     Household and
                                                     Similar Electrical
                                                     Appliances, Part 2:
                                                     Particular
                                                     Requirements for
                                                     Electric Irons (see
                                                     Note 3 below).
UL 1010 Receptacle Plug       Withdrawn...........  UL 1203 Explosion
 Combinations for Use in                             Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 1097 Double Insulation     No requirement for    NA.
 Systems for Use in            NRTL approval
 Electrical Equipment.         because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1411 Transformers and      No requirement for    NA.
 Motor Transformers for Use    NRTL approval
 In Audio-, Radio-, and        because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1412 Fusing Resistors and  No requirement for    NA.
 Temperature-Limited           NRTL approval
 Resistors for Radio-, and     because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1413 High Voltage          No requirement for    NA.
 Components for Television     NRTL approval
 Type Appliances.              because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1414 Across-the-Line,      No requirement for    NA.
 Antenna-Coupling, and Line-   NRTL approval
 by-Pass Capacitors for        because the
 Radio- and Television-Type    standard covers
 Appliances.                   components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1416 Overcurrent and       No requirement for    NA.
 Overtemperature Protectors    NRTL approval
 for Radio- and Television-    because the
 Type Appliances.              standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1417 Special Fuses for     No requirement for    NA.
 Radio- and Television-Type    NRTL approval
 Appliances.                   because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1433 Control Centers for   Withdrawn...........  No replacement.
 Changing Message Type
 Electric Signs.
UL 1604 Electrical Equipment  Withdrawn...........  ANSI/ISA--12.12.01-
 for Use in Class I and II,                          2012 Nonincendive
 Division 2 and Class III                            Electrical
 Hazardous (Classified)                              Equipment for Use
 Locations.                                          in Class I and II,
                                                     Division 2 and
                                                     Class III,
                                                     Divisions 1 and 2
                                                     Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     3 below).
UL 1664 Immersion Detection   Withdrawn...........  No replacement.
 Circuit Interrupters.
UL 1666 Test for Flame        Test method;          NA.
 Propagation Height of         therefore, not an
 Electrical and Optical        appropriate test
 Fiber Cables Installed        standard.
 Vertically in Shafts.
UL 1684 Reinforced            Withdrawn...........  UL 2420 Belowground
 Thermosetting Resin Conduit                         Reinforced
 (RTRC) and Fittings.                                Thermosetting Resin
                                                     Conduit (RTRC) and
                                                     Fittings and UL
                                                     2515 Aboveground
                                                     Reinforced
                                                     Thermosetting Resin
                                                     Conduit (RTRC) and
                                                     Fittings (for both
                                                     replacement
                                                     standards, see Note
                                                     3 below).

[[Page 38398]]

 
UL 60691 Thermal-Links        No requirement for    NA.
 Requirements and              NRTL approval
 Application Guide.            because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
------------------------------------------------------------------------


    Note 2:  OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Moreover, OSHA already 
includes the proposed replacement test standard in the NRTL's scope 
of recognition. Therefore, no further demonstration of capability is 
necessary at this time.


    Note 3:  OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Therefore, OSHA proposes 
to incorporate the replacement test standard into the NRTLs' scopes 
of recognition without requiring the NRTL to further demonstrate 
capability, as specified by 29 CFR 1910.7(b)(1).


Table 3--Test Standards OSHA Proposes To Delete From or Incorporate Into
              the Scope of Recognition of Curtis-Straus LLC
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed  test standard(s) (if
          standard                  deletion             applicable)
------------------------------------------------------------------------
UL 544 Medical and Dental     Withdrawn...........  UL 60601-1 Medical
 Equipment.                                          Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 2
                                                     below).
------------------------------------------------------------------------


    Note 2:  OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Moreover, OSHA already 
includes the proposed replacement test standard in the NRTL's scope 
of recognition. Therefore, no further demonstration of capability is 
necessary at this time.


Table 4--Test Standards OSHA Proposes To Delete From or Incorporate Into
              the Scope of Recognition of FM Approvals LLC
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed    test standard(s)
          standard                  deletion           (if applicable)
------------------------------------------------------------------------
UL 698 Industrial Control     Withdrawn...........  UL 1203 Explosion
 Equipment for Use in                                Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 781 Portable Electric      Withdrawn...........  UL 844 Electric
 Lighting Units for Use in                           Lighting Fixtures
 Hazardous (Classified)                              for Use in
 Locations.                                          Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 877 Circuit Breakers and   Withdrawn...........  UL 1203 Explosion
 Circuit Breaker Enclosures                          Proof and Dust
 for Use in Hazardous                                Ignition Proof
 (Classified) Locations (UL                          Electrical
 1203).                                              Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 886 Outlet Boxes and       Withdrawn...........  UL 1203 Explosion
 Fittings for Use in                                 Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 894 Switches for Use in    Withdrawn...........  UL 1203 Explosion
 Hazardous (Classified)                              Proof and Dust
 Locations.                                          Ignition Proof
                                                     Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 1002 Electrically          Withdrawn...........  UL 1203 Explosion
 Operated Valves for Use in                          Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
------------------------------------------------------------------------


    Note 2: OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Moreover, OSHA already 
includes the proposed replacement test standard in the NRTL's scope 
of recognition. Therefore, no further demonstration of capability is 
necessary at this time.


[[Page 38399]]



Table 5--Test Standards OSHA Proposes To Delete From or Incorporate Into
     the Scope of Recognition of Intertek Testing Services NA, Inc.
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed    test standard(s)
          standard                  deletion           (if applicable)
------------------------------------------------------------------------
ANSI A90.1 Safety Standard    29 CFR 1910.68 does   NA.
 for Belt Manlifts.            not require testing
                               and certification
                               for covered
                               product(s); also
                               not an appropriate
                               test standard
                               because it covers
                               primarily the
                               manufacture,
                               installation,
                               maintenance,
                               inspection, and
                               operation of
                               manlifts, not
                               safety testing.
ASTM E2074 Standard Test      Withdrawn...........  No replacement.
 Method for Fire Tests of
 Door Assemblies, Including
 Positive Pressure Testing
 of Side-Hinged and Pivoted
 Swinging Door Assemblies.
ANSI/NFPA 11A Medium- and     Withdrawn; moreover,  NA. Although
 High-Expansion Foam Systems.  OSHA standards do     replaced by ANSI/
                               not require testing   NFPA 11, ANSI/NFPA
                               and certification     11 is not an
                               for covered systems.  appropriate test
                                                     standard (see 75 FR
                                                     77002, 77004-77005,
                                                     Dec. 10, 2010, for
                                                     discussion of why
                                                     ANSI/NFPA 11 is not
                                                     appropriate).
ANSI/NFPA 20 Installation of  Not an appropriate    NA.
 Stationary Fire Pumps for     test standard
 Fire Protection.              because it covers
                               primarily the
                               selection and
                               installation of
                               these pumps, not
                               safety testing.
UL 94 Tests for Flammability  No requirement for    NA.
 of Plastic Materials for      NRTL approval
 Parts in Devices and          because the
 Appliances.                   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 187 X Ray Equipment......  Withdrawn...........  UL 60601-1 Medical
                                                     Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 2
                                                     below).
UL 207 Refrigerant-           No requirement for    NA.
 Containing Components and     NRTL approval
 Accessories, Nonelectrical.   because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 343 Pumps for Oil-Burning  No requirement for    NA.
 Appliances.                   NRTL approval of
                               this type of pump.
UL 512 Fuseholders..........  Withdrawn...........  UL 4248-1
                                                     Fuseholders--Part
                                                     1: General
                                                     Requirements.
                                                    UL 4248-4
                                                     Fuseholders--Part
                                                     4: Class CC.
                                                    UL 4248-5
                                                     Fuseholders--Part
                                                     5: Class G.
                                                    UL 4248-6
                                                     Fuseholders--Part
                                                     6: Class H.
                                                    UL 4248-8
                                                     Fuseholders--Part
                                                     8: Class J.
                                                    UL 4248-9
                                                     Fuseholders--Part
                                                     9: Class K.
                                                    UL 4248-11
                                                     Fuseholders--Part
                                                     11: Type C (Edison
                                                     Base) and Type S
                                                     Plug Fuse.
                                                    UL 4248-12
                                                     Fuseholders--Part
                                                     12: Class R.
                                                    UL 4248-15
                                                     Fuseholders--Part
                                                     15: Class T (for
                                                     all replacement
                                                     standards, see Note
                                                     3 below).
UL 544 Medical and Dental     Withdrawn...........  UL 60601-1 Medical
 Equipment.                                          Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 2
                                                     below).
UL 632 Electrically-Actuated  Withdrawn...........  No replacement.
 Transmitters.
UL 651B Continuous Length     Withdrawn...........  UL 651A Schedule 40
 HDPE Conduit.                                       and 80 High Density
                                                     Polyethylene (HDPE)
                                                     Conduit (see Note 2
                                                     below).
UL 698 Industrial Control     Withdrawn...........  UL 1203 Explosion
 Equipment for Use in                                Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 745-2-2 Particular         Withdrawn...........  UL 60745-2-2 Hand-
 Requirements for                                    Held Motor-Operated
 Screwdrivers and Impact                             Electric Tools--
 Wrenches.                                           Safety--Part 2-2:
                                                     Particular
                                                     Requirements for
                                                     Screwdrivers and
                                                     Impact Wrenches
                                                     (see Note 3 below).
UL 745-2-4 Particular         Withdrawn...........  UL 60745-2-4 Hand-
 Requirements for Sanders.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-4:
                                                     Particular
                                                     Requirements for
                                                     Sanders and
                                                     Polishers Other
                                                     Than Disk Type (see
                                                     Note 3 below).
UL 745-2-6 Particular         Withdrawn...........  UL 60745-2-6 Hand-
 Requirements for Hammers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-6:
                                                     Particular
                                                     Requirements for
                                                     Hammers (see Note 3
                                                     below).
UL 745-2-8 Particular         Withdrawn...........  UL 60745-2-8 Hand-
 Requirements for Shears and                         Held Motor-Operated
 Nibblers.                                           Electric Tools
                                                     Safety--Part 2-8:
                                                     Particular
                                                     Requirements for
                                                     Shears and Nibblers
                                                     (see Note 3 below).

[[Page 38400]]

 
UL 745-2-9 Particular         Withdrawn...........  UL 60745-2-9 Hand-
 Requirements for Tappers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-9:
                                                     Particular
                                                     Requirements for
                                                     Tappers (see Note 3
                                                     below).
UL 745-2-11 Particular        Withdrawn...........  UL 60745-2-11 Hand-
 Requirements for                                    Held Motor-Operated
 Reciprocating Saws.                                 Electric Tools--
                                                     Safety--Part 2-11:
                                                     Particular
                                                     Requirements for
                                                     Reciprocating Saws
                                                     (see Note 3 below).
UL 745-2-12 Particular        Withdrawn...........  UL 60745-2-12 Hand-
 Requirements for Concrete                           Held Motor-Operated
 Vibrators.                                          Electric Tools--
                                                     Safety--Part 2-12:
                                                     Particular
                                                     Requirements For
                                                     Concrete Vibrators
                                                     (see Note 3 below).
UL 745-2-30 Particular        Withdrawn...........  UL 60745-2-16 Hand-
 Requirements for Staplers.                          Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-16:
                                                     Particular
                                                     Requirements for
                                                     Tackers (see Note 3
                                                     below).
UL 745-2-33 Particular        Withdrawn...........  UL 60745-2-20 Hand-
 Requirements for Portable                           Held Motor-Operated
 Bandsaw.                                            Electric Tools--
                                                     Safety--Part 2-20:
                                                     Particular
                                                     Requirements For
                                                     Band Saws (see Note
                                                     3 below).
UL 745-2-34 Particular        Withdrawn...........  UL 60745-2-18 Hand-
 Requirements for Strapping                          Held Motor-Operated
 Tools.                                              Electric Tools--
                                                     Safety--Part 2-18:
                                                     Particular
                                                     Requirements For
                                                     Strapping Tools
                                                     (see Note 3 below).
UL 746A Polymeric Materials   No requirement for    NA.
 Short Term Property           NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746B Polymeric Materials   No requirement for    NA.
 Long Term Property            NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746C Polymeric Materials-- No requirement for    NA.
 Use in Electrical Equipment   NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746E Polymeric Materials-- No requirement for    NA.
 Industrial Laminates,         NRTL approval
 Filament Wound Tubing,        because the
 Vulcanized Fibre, and         standard covers
 Materials Used in Printed-    components that are
 Wiring Boards.                not appropriate for
                               use as end-use
                               products.
UL 781 Portable Electric      Withdrawn...........  UL 844 Electric
 Lighting Units for Use in                           Lighting Fixtures
 Hazardous (Classified)                              for Use in
 Locations.                                          Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 796 Printed[dash]Wiring    No requirement for    NA.
 Boards.                       NRTL approval
                               because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products..
UL 877 Circuit Breakers and   Withdrawn...........  UL 1203 Explosion
 Circuit Breaker Enclosures                          Proof and Dust
 for Use in Hazardous                                Ignition Proof
 (Classified) Locations (UL                          Electrical
 1203).                                              Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 886 Outlet Boxes and       Withdrawn...........  UL 1203 Explosion
 Fittings for Use in                                 Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 894 Switches for Use in    Withdrawn...........  UL 1203 Explosion
 Hazardous (Classified)                              Proof and Dust
 Locations.                                          Ignition Proof
                                                     Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 983 Surveillance Camera    Withdrawn...........  No replacement.
 Units.
UL 1002 Electrically          Withdrawn...........  UL 1203 Explosion
 Operated Valves for Use in                          Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 1005 Electric Flatirons..  Withdrawn...........  UL 60335-2-3
                                                     Household and
                                                     Similar Electrical
                                                     Appliances, Part 2:
                                                     Particular
                                                     Requirements for
                                                     Electric Irons (see
                                                     Note 3 below).
UL 1010 Receptacle Plug       Withdrawn...........  UL 1203 Explosion
 Combinations for Use in                             Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).

[[Page 38401]]

 
UL 1075 Gas-Fired Cooking     Withdrawn...........  No replacement.
 Appliances for Recreational
 Vehicles.
UL 1097 Double Insulation     No requirement for    NA.
 Systems for Use in            NRTL approval
 Electrical Equipment.         because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1411 Transformers and      No requirement for    NA.
 Motor Transformers for Use    NRTL approval
 In Audio-, Radio-, and        because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1412 Fusing Resistors and  No requirement for    NA.
 Temperature-Limited           NRTL approval
 Resistors for Radio- and      because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1413 High Voltage          No requirement for    NA.
 Components for Television     NRTL approval
 Type Appliances.              because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1414 Across-the-Line,      No requirement for    NA.
 Antenna-Coupling, and Line-   NRTL approval
 by-Pass Capacitors for        because the
 Radio- and Television-Type    standard covers
 Appliances.                   components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1416 Overcurrent and       No requirement for    NA.
 Overtemperature Protectors    NRTL approval
 for Radio- and Television-    because the
 Type Appliances.              standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1417 Special Fuses for     No requirement for    NA.
 Radio- and Television-Type    NRTL approval
 Appliances.                   because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1433 Control Centers for   Withdrawn...........  No replacement.
 Changing Message Type
 Electric Signs.
UL 1445 Electric Water Bed    Withdrawn...........  No replacement.
 Heaters.
UL 1604 Electrical Equipment  Withdrawn...........  ANSI/ISA--12.12.01-
 for Use in Class I and II,                          2012 Nonincendive
 Division 2 and Class III                            Electrical
 Hazardous (Classified)                              Equipment for Use
 Locations.                                          in Class I and II,
                                                     Division 2 and
                                                     Class III,
                                                     Divisions 1 and 2
                                                     Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 1664 Immersion Detection   Withdrawn...........  No replacement.
 Circuit Interrupters.
UL 1666 Test for Flame        Test method;          NA.
 Propagation Height of         therefore, not an
 Electrical and Optical        appropriate test
 Fiber Cables Installed        standard.
 Vertically in Shafts.
UL 1694 Tests for             No requirement for    NA.
 Flammability of Small         NRTL approval
 Polymeric Component           because the
 Materials.                    standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 2106 Field Erected Boiler  No requirement for    NA.
 Assemblies.                   NRTL approval in
                               OSHA requirements;
                               test standard
                               applies to boilers
                               burning fuel.
UL 60691 Thermal-Links-       No requirement for    NA.
 Requirements and              NRTL approval
 Application Guide.            because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
------------------------------------------------------------------------


    Note 2: OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Moreover, OSHA already 
includes the proposed replacement test standard in the NRTL's scope 
of recognition. Therefore, no further demonstration of capability is 
necessary at this time.


    Note 3: OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Therefore, OSHA proposes 
to incorporate the replacement test standard into the NRTLs' scopes 
of recognition without requiring the NRTL to further demonstrate 
capability, as specified by 29 CFR 1910.7(b)(1).


Table 6--Test Standards OSHA Proposes To Delete From or Incorporate Into
           the Scope of Recognition of MET Laboratories, Inc.
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed  test standard(s) (if
          standard                  deletion             applicable)
------------------------------------------------------------------------
UL 187 X Ray Equipment......  Withdrawn...........  UL 60601-1 Medical
                                                     Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 2
                                                     below).
UL 544 Medical and Dental     Withdrawn...........  UL 60601-1 Medical
 Equipment.                                          Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 2
                                                     below).

[[Page 38402]]

 
UL 698 Industrial Control     Withdrawn...........  UL 1203 Explosion
 Equipment for Use in                                Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 745-2-2 Particular         Withdrawn...........  UL 60745-2-2 Hand-
 Requirements for                                    Held Motor-Operated
 Screwdrivers and Impact                             Electric Tools--
 Wrenches.                                           Safety--Part 2-2:
                                                     Particular
                                                     Requirements for
                                                     Screwdrivers and
                                                     Impact Wrenches
                                                     (see Note 3 below).
UL 745-2-4 Particular         Withdrawn...........  UL 60745-2-4 Hand-
 Requirements for Sanders.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-4:
                                                     Particular
                                                     Requirements for
                                                     Sanders and
                                                     Polishers Other
                                                     Than Disk Type (see
                                                     Note 3 below).
UL 745-2-6 Particular         Withdrawn...........  UL 60745-2-6 Hand-
 Requirements for Hammers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-6:
                                                     Particular
                                                     Requirements for
                                                     Hammers (see Note 3
                                                     below).
UL 745-2-8 Particular         Withdrawn...........  UL 60745-2-8 Hand-
 Requirements for Shears and                         Held Motor-Operated
 Nibblers.                                           Electric Tools
                                                     Safety--Part 2-8:
                                                     Particular
                                                     Requirements for
                                                     Shears and Nibblers
                                                     (see Note 3 below).
UL 745-2-9 Particular         Withdrawn...........  UL 60745-2-9 Hand-
 Requirements for Tappers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-9:
                                                     Particular
                                                     Requirements for
                                                     Tappers (see Note 3
                                                     below).
UL 745-2-11 Particular        Withdrawn...........  UL 60745-2-11 Hand-
 Requirements for                                    Held Motor-Operated
 Reciprocating Saws.                                 Electric Tools--
                                                     Safety--Part 2-11:
                                                     Particular
                                                     Requirements for
                                                     Reciprocating Saws
                                                     (see Note 3 below).
UL 745-2-12 Particular        Withdrawn...........  UL 60745-2-12 Hand-
 Requirements for Concrete                           Held Motor-Operated
 Vibrators.                                          Electric Tools--
                                                     Safety--Part 2-12:
                                                     Particular
                                                     Requirements For
                                                     Concrete Vibrators
                                                     (see Note 3 below).
UL 745-2-30 Particular        Withdrawn...........  UL 60745-2-16 Hand-
 Requirements for Staplers.                          Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-16:
                                                     Particular
                                                     Requirements for
                                                     Tackers (see Note 3
                                                     below).
UL 745-2-33 Particular        Withdrawn...........  UL 60745-2-20 Hand-
 Requirements for Portable                           Held Motor-Operated
 Bandsaw.                                            Electric Tools--
                                                     Safety--Part 2-20:
                                                     Particular
                                                     Requirements For
                                                     Band Saws (see Note
                                                     3 below).
UL 745-2-34 Particular        Withdrawn...........  UL 60745-2-18 Hand-
 Requirements for Strapping                          Held Motor-Operated
 Tools.                                              Electric Tools--
                                                     Safety--Part 2-18:
                                                     Particular
                                                     Requirements For
                                                     Strapping Tools
                                                     (see Note 3 below).
UL 886 Outlet Boxes and       Withdrawn...........  UL 1203 Explosion
 Fittings for Use in                                 Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 983 Surveillance Camera    Withdrawn...........  No replacement.
 Units.
UL 1005 Electric Flatirons..  Withdrawn...........  UL 60335-2-3
                                                     Household and
                                                     Similar Electrical
                                                     Appliances, Part 2:
                                                     Particular
                                                     Requirements for
                                                     Electric Irons (see
                                                     Note 3 below).
UL 1411 Transformers and      No requirement for    NA.
 Motor Transformers for Use    NRTL approval
 In Audio-, Radio-, and        because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1433 Control Centers for   Withdrawn...........  No replacement.
 Changing Message Type
 Electric Signs.
UL 1604 Electrical Equipment  Withdrawn...........  ANSI/ISA--12.12.01-
 for Use in Class I and II,                          2012 Nonincendive
 Division 2 and Class III                            Electrical
 Hazardous (Classified)                              Equipment for Use
 Locations.                                          in Class I and II,
                                                     Division 2 and
                                                     Class III,
                                                     Divisions 1 and 2
                                                     Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     3 below).
------------------------------------------------------------------------


    Note 2: OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Moreover, OSHA already 
includes the proposed replacement test standard in the NRTL's scope 
of recognition. Therefore, no further demonstration of capability is 
necessary at this time.


    Note 3: OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Therefore, OSHA proposes 
to incorporate the

[[Page 38403]]

replacement test standard into the NRTLs' scopes of recognition 
without requiring the NRTL to further demonstrate capability, as 
specified by 29 CFR 1910.7(b)(1).


Table 7--Test Standards OSHA Proposes To Delete From or Incorporate Into
              the Scope of Recognition of NSF International
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed  test standard(s) (if
          standard                  deletion             applicable)
------------------------------------------------------------------------
UL 651B Continuous Length     Withdrawn...........  UL 651A Schedule 40
 HDPE Conduit.                                       and 80 High Density
                                                     Polyethylene (HDPE)
                                                     Conduit (see Note 2
                                                     below).
------------------------------------------------------------------------


    Note 2: OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Moreover, OSHA already 
includes the proposed replacement test standard in the NRTL's scope 
of recognition. Therefore, no further demonstration of capability is 
necessary at this time.


Table 8--Test Standards OSHA Proposes To Delete From or Incorporate Into
       the Scope of Recognition of SGS U.S. Testing Company, Inc.
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed  test standard(s) (if
          standard                  deletion             applicable)
------------------------------------------------------------------------
UL 544 Medical and Dental     Withdrawn...........  UL 60601-1 Medical
 Equipment.                                          Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 2
                                                     below).
UL 632 Electrically-Actuated  Withdrawn...........  No replacement.
 Transmitters.
UL 1604 Electrical Equipment  Withdrawn...........  ANSI/ISA--12.12.01-
 for Use in Class I and II,                          2012 Nonincendive
 Division 2 and Class III                            Electrical
 Hazardous (Classified)                              Equipment for Use
 Locations.                                          in Class I and II,
                                                     Division 2 and
                                                     Class III,
                                                     Divisions 1 and 2
                                                     Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     3 below).
------------------------------------------------------------------------


    Note 2: OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Moreover, OSHA already 
includes the proposed replacement test standard in the NRTL's scope 
of recognition. Therefore, no further demonstration of capability is 
necessary at this time.


    Note 3:  OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Therefore, OSHA proposes 
to incorporate the replacement test standard into the NRTLs' scopes 
of recognition without requiring the NRTL to further demonstrate 
capability, as specified by 29 CFR 1910.7(b)(1).


    Table 9--Test Standard OSHA Proposes To Delete From the Scope of
               Recognition of Southwest Research Institute
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed  test standard(s) (if
          standard                  deletion             applicable)
------------------------------------------------------------------------
ASTM E2074 Standard Test      Withdrawn...........  No replacement.
 Method for Fire Tests of
 Door Assemblies, Including
 Positive Pressure Testing
 of Side-Hinged and Pivoted
 Swinging Door Assemblies.
------------------------------------------------------------------------


  Table 10--Test Standards OSHA Proposes To Delete From or Incorporate
           Into the Scope of Recognition of TUV America, Inc.
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed  test standard(s) (if
          standard                  deletion             applicable)
------------------------------------------------------------------------
UL 745-2-2 Particular         Withdrawn...........  UL 60745-2-2 Hand-
 Requirements for                                    Held Motor-Operated
 Screwdrivers and Impact                             Electric Tools--
 Wrenches.                                           Safety--Part 2-2:
                                                     Particular
                                                     Requirements for
                                                     Screwdrivers and
                                                     Impact Wrenches
                                                     (see Note 3 below).
UL 745-2-4 Particular         Withdrawn...........  UL 60745-2-4 Hand-
 Requirements for Sanders.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-4:
                                                     Particular
                                                     Requirements for
                                                     Sanders and
                                                     Polishers Other
                                                     Than Disk Type (see
                                                     Note 3 below).
UL 745-2-6 Particular         Withdrawn...........  UL 60745-2-6 Hand-
 Requirements for Hammers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-6:
                                                     Particular
                                                     Requirements for
                                                     Hammers (see Note 3
                                                     below).

[[Page 38404]]

 
UL 745-2-8 Particular         Withdrawn...........  UL 60745-2-8 Hand-
 Requirements for Shears and                         Held Motor-Operated
 Nibblers.                                           Electric Tools
                                                     Safety--Part 2-8:
                                                     Particular
                                                     Requirements for
                                                     Shears and Nibblers
                                                     (see Note 3 below).
UL 745-2-9 Particular         Withdrawn...........  UL 60745-2-9 Hand-
 Requirements for Tappers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-9:
                                                     Particular
                                                     Requirements for
                                                     Tappers (see Note 3
                                                     below).
UL 745-2-11 Particular        Withdrawn...........  UL 60745-2-11 Hand-
 Requirements for                                    Held Motor-Operated
 Reciprocating Saws.                                 Electric Tools--
                                                     Safety--Part 2-11:
                                                     Particular
                                                     Requirements for
                                                     Reciprocating Saws
                                                     (see Note 3 below).
UL 745-2-12 Particular        Withdrawn...........  UL 60745-2-12 Hand-
 Requirements for Concrete                           Held Motor-Operated
 Vibrators.                                          Electric Tools--
                                                     Safety--Part 2-12:
                                                     Particular
                                                     Requirements For
                                                     Concrete Vibrators
                                                     (see Note 3 below).
UL 745-2-30 Particular        Withdrawn...........  UL 60745-2-16 Hand-
 Requirements for Staplers.                          Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-16:
                                                     Particular
                                                     Requirements for
                                                     Tackers (see Note 3
                                                     below).
UL 745-2-33 Particular        Withdrawn...........  UL 60745-2-20 Hand-
 Requirements for Portable                           Held Motor-Operated
 Bandsaw.                                            Electric Tools--
                                                     Safety--Part 2-20:
                                                     Particular
                                                     Requirements For
                                                     Band Saws (see Note
                                                     3 below).
UL 745-2-34 Particular        Withdrawn...........  UL 60745-2-18 Hand-
 Requirements for Strapping                          Held Motor-Operated
 Tools.                                              Electric Tools--
                                                     Safety--Part 2-18:
                                                     Particular
                                                     Requirements For
                                                     Strapping Tools
                                                     (see Note 3 below).
UL 1005 Electric Flatirons..  Withdrawn...........  UL 60335-2-3
                                                     Household and
                                                     Similar Electrical
                                                     Appliances, Part 2:
                                                     Particular
                                                     Requirements for
                                                     Electric Irons (see
                                                     Note 2 below).
UL 1097 Double Insulation     No requirement for    NA.
 Systems for Use in            NRTL approval
 Electrical Equipment.         because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1411 Transformers and      No requirement for    NA.
 Motor Transformers for Use    NRTL approval
 In Audio-, Radio-, and        because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
------------------------------------------------------------------------


    Note 2: OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Moreover, OSHA already 
includes the proposed replacement test standard in the NRTL's scope 
of recognition. Therefore, no further demonstration of capability is 
necessary at this time.


    Note 3: OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Therefore, OSHA proposes 
to incorporate the replacement test standard into the NRTLs' scopes 
of recognition without requiring the NRTL to further demonstrate 
capability, as specified by 29 CFR 1910.7(b)(1).


  Table 11--Test Standards OSHA Proposes To Delete From or Incorporate
       Into the Scope of Recognition of TUV Product Services GmbH
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed  test standard(s) (if
          standard                  deletion             applicable)
------------------------------------------------------------------------
UL 745-2-2 Particular         Withdrawn...........  UL 60745-2-2 Hand-
 Requirements for                                    Held Motor-Operated
 Screwdrivers and Impact                             Electric Tools--
 Wrenches.                                           Safety--Part 2-2:
                                                     Particular
                                                     Requirements for
                                                     Screwdrivers and
                                                     Impact Wrenches
                                                     (see Note 3 below).
UL 745-2-4 Particular         Withdrawn...........  UL 60745-2-4 Hand-
 Requirements for Sanders.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-4:
                                                     Particular
                                                     Requirements for
                                                     Sanders and
                                                     Polishers Other
                                                     Than Disk Type (see
                                                     Note 3 below).
UL 745-2-6 Particular         Withdrawn...........  UL 60745-2-6 Hand-
 Requirements for Hammers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-6:
                                                     Particular
                                                     Requirements for
                                                     Hammers (see Note 3
                                                     below).
UL 745-2-8 Particular         Withdrawn...........  UL 60745-2-8 Hand-
 Requirements for Shears and                         Held Motor-Operated
 Nibblers.                                           Electric Tools
                                                     Safety--Part 2-8:
                                                     Particular
                                                     Requirements for
                                                     Shears and Nibblers
                                                     (see Note 3 below).

[[Page 38405]]

 
UL 745-2-9 Particular         Withdrawn...........  UL 60745-2-9 Hand-
 Requirements for Tappers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-9:
                                                     Particular
                                                     Requirements for
                                                     Tappers (see Note 3
                                                     below).
UL 745-2-11 Particular        Withdrawn...........  UL 60745-2-11 Hand-
 Requirements for                                    Held Motor-Operated
 Reciprocating Saws.                                 Electric Tools--
                                                     Safety--Part 2-11:
                                                     Particular
                                                     Requirements for
                                                     Reciprocating Saws
                                                     (see Note 3 below).
UL 745-2-12 Particular        Withdrawn...........  UL 60745-2-12 Hand-
 Requirements for Concrete                           Held Motor-Operated
 Vibrators.                                          Electric Tools--
                                                     Safety--Part 2-12:
                                                     Particular
                                                     Requirements For
                                                     Concrete Vibrators
                                                     (see Note 3 below).
UL 745-2-30 Particular        Withdrawn...........  UL 60745-2-16 Hand-
 Requirements for Staplers.                          Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-16:
                                                     Particular
                                                     Requirements for
                                                     Tackers (see Note 3
                                                     below).
UL 745-2-33 Particular        Withdrawn...........  UL 60745-2-20 Hand-
 Requirements for Portable                           Held Motor-Operated
 Bandsaw.                                            Electric Tools--
                                                     Safety--Part 2-20:
                                                     Particular
                                                     Requirements For
                                                     Band Saws (see Note
                                                     3 below).
UL 745-2-34 Particular        Withdrawn...........  UL 60745-2-18 Hand-
 Requirements for Strapping                          Held Motor-Operated
 Tools.                                              Electric Tools--
                                                     Safety--Part 2-18:
                                                     Particular
                                                     Requirements For
                                                     Strapping Tools
                                                     (see Note 3 below).
UL 1005 Electric Flatirons..  Withdrawn...........  UL 60335-2-3
                                                     Household and
                                                     Similar Electrical
                                                     Appliances, Part 2:
                                                     Particular
                                                     Requirements for
                                                     Electric Irons (see
                                                     Note 3 below).
UL 1411 Transformers and      No requirement for    NA.
 Motor Transformers for Use    NRTL approval
 In Audio-, Radio-, and        because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
------------------------------------------------------------------------


    Note 3: OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Therefore, OSHA proposes 
to incorporate the replacement test standard into the NRTLs' scopes 
of recognition without requiring the NRTL to further demonstrate 
capability, as specified by 29 CFR 1910.7(b)(1).


  Table 12--Test Standards OSHA Proposes To Delete From or Incorporate
  Into the Scope of Recognition of TUV Rheinland of North America, Inc.
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed  test standard(s) (if
          standard                  deletion             applicable)
------------------------------------------------------------------------
ANSI A90.1 Safety Standard    29 CFR 1910.68 does   NA.
 for Belt Manlifts.            not require testing
                               and certification
                               for covered
                               product(s); also
                               not an appropriate
                               test standard
                               because it covers
                               primarily the
                               manufacture,
                               installation,
                               maintenance,
                               inspection, and
                               operation of
                               manlifts, not
                               safety testing.
UL 745-2-2 Particular         Withdrawn...........  UL 60745-2-2 Hand-
 Requirements for                                    Held Motor-Operated
 Screwdrivers and Impact                             Electric Tools--
 Wrenches.                                           Safety--Part 2-2:
                                                     Particular
                                                     Requirements for
                                                     Screwdrivers and
                                                     Impact Wrenches
                                                     (see Note 3 below).
UL 745-2-4 Particular         Withdrawn...........  UL 60745-2-4 Hand-
 Requirements for Sanders.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-4:
                                                     Particular
                                                     Requirements for
                                                     Sanders and
                                                     Polishers Other
                                                     Than Disk Type (see
                                                     Note 3 below).
UL 745-2-6 Particular         Withdrawn...........  UL 60745-2-6 Hand-
 Requirements for Hammers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-6:
                                                     Particular
                                                     Requirements for
                                                     Hammers (see Note 3
                                                     below).
UL 745-2-8 Particular         Withdrawn...........  UL 60745-2-8 Hand-
 Requirements for Shears and                         Held Motor-Operated
 Nibblers.                                           Electric Tools
                                                     Safety--Part 2-8:
                                                     Particular
                                                     Requirements for
                                                     Shears and Nibblers
                                                     (see Note 3 below).
UL 745-2-9 Particular         Withdrawn...........  UL 60745-2-9 Hand-
 Requirements for Tappers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-9:
                                                     Particular
                                                     Requirements for
                                                     Tappers (see Note 3
                                                     below).

[[Page 38406]]

 
UL 745-2-11 Particular        Withdrawn...........  UL 60745-2-11 Hand-
 Requirements for                                    Held Motor-Operated
 Reciprocating Saws.                                 Electric Tools--
                                                     Safety--Part 2-11:
                                                     Particular
                                                     Requirements for
                                                     Reciprocating Saws
                                                     (see Note 3 below).
UL 745-2-12 Particular        Withdrawn...........  UL 60745-2-12 Hand-
 Requirements for Concrete                           Held Motor-Operated
 Vibrators.                                          Electric Tools--
                                                     Safety--Part 2-12:
                                                     Particular
                                                     Requirements For
                                                     Concrete Vibrators
                                                     (see Note 3 below).
UL 745-2-30 Particular        Withdrawn...........  UL 60745-2-16 Hand-
 Requirements for Staplers.                          Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-16:
                                                     Particular
                                                     Requirements for
                                                     Tackers (see Note 3
                                                     below).
UL 745-2-33 Particular        Withdrawn...........  UL 60745-2-20 Hand-
 Requirements for Portable                           Held Motor-Operated
 Bandsaw.                                            Electric Tools--
                                                     Safety--Part 2-20:
                                                     Particular
                                                     Requirements For
                                                     Band Saws (see Note
                                                     3 below).
UL 745-2-34 Particular        Withdrawn...........  UL 60745-2-18 Hand-
 Requirements for Strapping                          Held Motor-Operated
 Tools.                                              Electric Tools--
                                                     Safety--Part 2-18:
                                                     Particular
                                                     Requirements For
                                                     Strapping Tools
                                                     (see Note 3 below).
UL 983 Surveillance Camera    Withdrawn...........  No replacement.
 Units.
UL 1005 Electric Flatirons..  Withdrawn...........  UL 60335-2-3
                                                     Household and
                                                     Similar Electrical
                                                     Appliances, Part 2:
                                                     Particular
                                                     Requirements for
                                                     Electric Irons (see
                                                     Note 3 below),
UL 1097 Double Insulation     No requirement for    NA.
 Systems for Use in            NRTL approval
 Electrical Equipment.         because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1411 Transformers and      No requirement for    NA.
 Motor Transformers for Use    NRTL approval
 In Audio-, Radio-, and        because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1414 Across-the-Line,      No requirement for    NA.
 Antenna-Coupling, and Line-   NRTL approval
 by-Pass Capacitors for        because the
 Radio- and Television-Type    standard covers
 Appliances.                   components that are
                               not appropriate for
                               use as end-use
                               products.
UL 2106 Field Erected Boiler  No requirement for    NA.
 Assemblies.                   NRTL approval in
                               OSHA requirements;
                               test standard
                               applies to boilers
                               burning fuel.
------------------------------------------------------------------------


    Note 3:  OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Therefore, OSHA proposes 
to incorporate the replacement test standard into the NRTLs' scopes 
of recognition without requiring the NRTL to further demonstrate 
capability, as specified by 29 CFR 1910.7(b)(1).


  Table 13--Test Standards OSHA Proposes To Delete From or Incorporate
     Into the Scope of Recognition of Underwriters Laboratories Inc.
------------------------------------------------------------------------
                                                    Proposed replacement
    Proposed deleted test      Reason for proposed    test standard(s)
          standard                  deletion           (if applicable)
------------------------------------------------------------------------
ANSI/NFPA 20 Installation of  Not an appropriate    NA.
 Stationary Fire Pumps for     test standard
 Fire Protection.              because it covers
                               primarily the
                               selection and
                               installation of
                               these pumps, not
                               safety testing.
UL 94 Tests for Flammability  No requirement for    NA.
 of Plastic Materials for      NRTL approval
 Parts in Devices and          because the
 Appliances.                   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 187 X Ray Equipment......  Withdrawn...........  UL 60601-1 Medical
                                                     Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 2
                                                     below).
UL 207 Refrigerant-           No requirement for    NA.
 Containing Components and     NRTL approval
 Accessories, Nonelectrical.   because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 343 Pumps for Oil-Burning  No requirement for    NA.
 Appliances.                   NRTL approval of
                               this type of pump.
UL 512 Fuseholders..........  Withdrawn...........  UL 4248-1
                                                     Fuseholders--Part
                                                     1: General
                                                     Requirements.
                                                    UL 4248-4
                                                     Fuseholders--Part
                                                     4: Class CC.
                                                    UL 4248-5
                                                     Fuseholders--Part
                                                     5: Class G.
                                                    UL 4248-6
                                                     Fuseholders--Part
                                                     6: Class H.
                                                    UL 4248-8
                                                     Fuseholders--Part
                                                     8: Class J.
                                                    UL 4248-9--
                                                     Fuseholders--Part
                                                     9: Class K.

[[Page 38407]]

 
                                                    UL 4248-11
                                                     Fuseholders--Part
                                                     11: Type C (Edison
                                                     Base) and Type S
                                                     Plug Fuse.
                                                    UL 4248-12
                                                     Fuseholders--Part
                                                     12: Class R.
                                                    UL 4248-15
                                                     Fuseholders--Part
                                                     15: Class T (for
                                                     all replacement
                                                     standards, see Note
                                                     3 below).
UL 544 Medical and Dental     Withdrawn...........  UL 60601-1 Medical
 Equipment.                                          Electrical
                                                     Equipment, Part 1:
                                                     General
                                                     Requirements for
                                                     Safety (see Note 2
                                                     below).
UL 651B Continuous Length     Withdrawn...........  UL 651A Schedule 40
 HDPE Conduit.                                       and 80 High Density
                                                     Polyethylene (HDPE)
                                                     Conduit (see Note 2
                                                     below).
UL 698 Industrial Control     Withdrawn...........  UL 1203 Explosion
 Equipment for Use in                                Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 745-2-2 Particular         Withdrawn...........  UL 60745-2-2 Hand-
 Requirements for                                    Held Motor-Operated
 Screwdrivers and Impact                             Electric Tools--
 Wrenches.                                           Safety--Part 2-2:
                                                     Particular
                                                     Requirements for
                                                     Screwdrivers and
                                                     Impact Wrenches
                                                     (see Note 2 below).
UL 745-2-4 Particular         Withdrawn...........  UL 60745-2-4 Hand-
 Requirements for Sanders.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-4:
                                                     Particular
                                                     Requirements for
                                                     Sanders and
                                                     Polishers Other
                                                     Than Disk Type (see
                                                     Note 2 below).
UL 745-2-6 Particular         Withdrawn...........  UL 60745-2-6 Hand-
 Requirements for Hammers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-6:
                                                     Particular
                                                     Requirements for
                                                     Hammers (see Note 2
                                                     below).
UL 745-2-8 Particular         Withdrawn...........  UL 60745-2-8 Hand-
 Requirements for Shears and                         Held Motor-Operated
 Nibblers.                                           Electric Tools
                                                     Safety--Part 2-8:
                                                     Particular
                                                     Requirements for
                                                     Shears and Nibblers
                                                     (see Note 2 below).
UL 745-2-9 Particular         Withdrawn...........  UL 60745-2-9 Hand-
 Requirements for Tappers.                           Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-9:
                                                     Particular
                                                     Requirements for
                                                     Tappers (see Note 2
                                                     below).
UL 745-2-11 Particular        Withdrawn...........  UL 60745-2-11 Hand-
 Requirements for                                    Held Motor-Operated
 Reciprocating Saws.                                 Electric Tools--
                                                     Safety--Part 2-11:
                                                     Particular
                                                     Requirements for
                                                     Reciprocating Saws
                                                     (see Note 2 below).
UL 745-2-12 Particular        Withdrawn...........  UL 60745-2-12 Hand-
 Requirements for Concrete                           Held Motor-Operated
 Vibrators.                                          Electric Tools--
                                                     Safety--Part 2-12:
                                                     Particular
                                                     Requirements For
                                                     Concrete Vibrators
                                                     (see Note 2 below).
UL 745-2-30 Particular        Withdrawn...........  UL 60745-2-16 Hand-
 Requirements for Staplers.                          Held Motor-Operated
                                                     Electric Tools--
                                                     Safety--Part 2-16:
                                                     Particular
                                                     Requirements for
                                                     Tackers (see Note 3
                                                     below).
UL 745-2-33 Particular        Withdrawn...........  UL 60745-2-20 Hand-
 Requirements for Portable                           Held Motor-Operated
 Bandsaw.                                            Electric Tools--
                                                     Safety--Part 2-20:
                                                     Particular
                                                     Requirements For
                                                     Band Saws (see Note
                                                     2 below).
UL 745-2-34 Particular        Withdrawn...........  UL 60745-2-18 Hand-
 Requirements for Strapping                          Held Motor-Operated
 Tools.                                              Electric Tools--
                                                     Safety--Part 2-18:
                                                     Particular
                                                     Requirements For
                                                     Strapping Tools
                                                     (see Note 2 below).
UL 746A Polymeric Materials   No requirement for    NA.
 Short Term Property           NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746B Polymeric Materials   No requirement for    NA.
 Long Term Property            NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746C Polymeric Materials-- No requirement for    NA.
 Use in Electrical Equipment   NRTL approval
 Evaluations.                  because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 746E Polymeric Materials-- No requirement for    NA.
 Industrial Laminates,         NRTL approval
 Filament Wound Tubing,        because the
 Vulcanized Fibre, and         standard covers
 Materials Used in Printed-    components that are
 Wiring Boards.                not appropriate for
                               use as end-use
                               products.

[[Page 38408]]

 
UL 781 Portable Electric      Withdrawn...........  UL 844 Electric
 Lighting Units for Use in                           Lighting Fixtures
 Hazardous (Classified)                              for Use in
 Locations.                                          Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 796 Printed-Wiring Boards  No requirement for    NA.
                               NRTL approval
                               because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 877 Circuit Breakers and   Withdrawn...........  UL 1203 Explosion
 Circuit Breaker Enclosures                          Proof and Dust
 for Use in Hazardous                                Ignition Proof
 (Classified) Locations (UL                          Electrical
 1203).                                              Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 886 Outlet Boxes and       Withdrawn...........  UL 1203 Explosion
 Fittings for Use in                                 Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 894 Switches for Use in    Withdrawn...........  UL 1203 Explosion
 Hazardous (Classified)                              Proof and Dust
 Locations.                                          Ignition Proof
                                                     Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 983 Surveillance Camera    Withdrawn...........  No replacement.
 Units.
UL 1002 Electrically          Withdrawn...........  UL 1203 Explosion
 Operated Valves for Use in                          Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 1005 Electric Flatirons..  Withdrawn...........  UL 60335-2-3
                                                     Household and
                                                     Similar Electrical
                                                     Appliances, Part 2:
                                                     Particular
                                                     Requirements for
                                                     Electric Irons (see
                                                     Note 3 below).
UL 1010 Receptacle Plug       Withdrawn...........  UL 1203 Explosion
 Combinations for Use in                             Proof and Dust
 Hazardous (Classified)                              Ignition Proof
 Locations.                                          Electrical
                                                     Equipment for Use
                                                     in Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 1075 Gas-Fired Cooking     Withdrawn...........  No replacement.
 Appliances for Recreational
 Vehicles.
UL 1097 Double Insulation     No requirement for    NA.
 Systems for Use in            NRTL approval
 Electrical Equipment.         because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1411 Transformers and      No requirement for    NA.
 Motor Transformers for Use    NRTL approval
 In Audio-, Radio-, and        because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1412 Fusing Resistors and  No requirement for    NA.
 Temperature-Limited           NRTL approval
 Resistors for Radio-, and     because the
 Television-Type Appliances.   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1413 High Voltage          No requirement for    NA.
 Components for Television     NRTL approval
 Type Appliances.              because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1414 Across-the-Line,      No requirement for    NA.
 Antenna-Coupling, and Line-   NRTL approval
 by-Pass Capacitors for        because the
 Radio- and Television-Type    standard covers
 Appliances.                   components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1416 Overcurrent and       No requirement for    NA.
 Overtemperature Protectors    NRTL approval
 for Radio- and Television-    because the
 Type Appliances.              standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1417 Special Fuses for     No requirement for    NA.
 Radio- and Television-Type    NRTL approval
 Appliances.                   because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1433 Control Centers for   Withdrawn...........  No replacement.
 Changing Message Type
 Electric Signs.
UL 1445 Electric Water Bed    Withdrawn...........  No replacement.
 Heaters.
UL 1604 Electrical Equipment  Withdrawn...........  ANSI/ISA--12.12.01-
 for Use in Class I and II,                          2012 Nonincendive
 Division 2 and Class III                            Electrical
 Hazardous (Classified)                              Equipment for Use
 Locations.                                          in Class I and II,
                                                     Division 2 and
                                                     Class III,
                                                     Divisions 1 and 2
                                                     Hazardous
                                                     (Classified)
                                                     Locations (see Note
                                                     2 below).
UL 1664 Immersion Detection   Withdrawn...........  No replacement.
 Circuit Interrupters.
UL 1666 Test for Flame        Test method;          NA.
 Propagation Height of         therefore, not an
 Electrical and Optical        appropriate test
 Fiber Cables Installed        standard.
 Vertically in Shafts.

[[Page 38409]]

 
UL 1684 Reinforced            Withdrawn...........  UL 2420 Belowground
 Thermosetting Resin Conduit                         Reinforced
 (RTRC) and Fittings.                                Thermosetting Resin
                                                     Conduit (RTRC) and
                                                     Fittings and UL
                                                     2515 Aboveground
                                                     Reinforced
                                                     Thermosetting Resin
                                                     Conduit (RTRC) and
                                                     Fittings (for both
                                                     replacement
                                                     standards, see Note
                                                     3 below).
UL 1686 Pin and Sleeve        Not an appropriate    NA.
 Configurations.               test standard; does
                               not specify safety
                               requirements for
                               covered devices;
                               provides the
                               physical dimensions
                               for covered devices
                               only.
UL 1692 Polymeric Materials   No requirement for    NA.
 Coil Forms.                   NRTL approval
                               because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 1694 Tests for             No requirement for    NA.
 Flammability of Small         NRTL approval
 Polymeric Component           because the
 Materials).                   standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
UL 2106 Field Erected Boiler  No requirement for    NA.
 Assemblies.                   NRTL approval in
                               OSHA requirements;
                               test standard
                               applies to boilers
                               burning fuel.
UL 60691 Thermal-Links-       No requirement for    NA.
 Requirements and              NRTL approval
 Application Guide.            because the
                               standard covers
                               components that are
                               not appropriate for
                               use as end-use
                               products.
------------------------------------------------------------------------


    Note 2:  OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Moreover, OSHA already 
includes the proposed replacement test standard in the NRTL's scope 
of recognition. Therefore, no further demonstration of capability is 
necessary at this time.


    Note 3:  OSHA believes the proposed replacement test standard is 
comparable to the withdrawn test standard. Therefore, OSHA proposes 
to incorporate the replacement test standard into the NRTLs' scopes 
of recognition without requiring the NRTL to further demonstrate 
capability, as specified by 29 CFR 1910.7(b)(1).

V. Authority and Signature

    David Michaels, Ph.D., MPH, Assistant Secretary of Labor for 
Occupational Safety and Health, 200 Constitution Avenue NW., 
Washington, DC 20210, authorized the preparation of this notice. 
Accordingly, the Agency is issuing this notice pursuant to 29 U.S.C. 
657(g)(2)), Secretary of Labor's Order No. 1-2012 (77 FR 3912, Jan. 25, 
2012), and 29 CFR 1910.7.

    Signed at Washington, DC, on June 20, 2013.
David Michaels,
Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2013-15228 Filed 6-25-13; 8:45 am]
BILLING CODE 4510-26-P


