[Federal Register Volume 87, Number 165 (Friday, August 26, 2022)]
[Notices]
[Pages 52614-52616]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-18417]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

National Highway Traffic Safety Administration

[Docket No. NHTSA-2022-0065; Notice 1]


Columbus Trading-Partners USA, Inc., Receipt of Petition for 
Decision of Inconsequential Noncompliance

AGENCY: National Highway Traffic Safety Administration (NHTSA), 
Department of Transportation (DOT).

ACTION: Receipt of petition.

-----------------------------------------------------------------------

SUMMARY: Columbus Trading-Partners USA, Inc., (CTP), has determined 
that certain Cybex child restraint systems distributed by CTP do not 
fully comply with Federal Motor Vehicle Safety Standard (FMVSS) No. 
213, Child Restraint Systems. CTP filed an original noncompliance 
report dated June 30, 2022. CTP petitioned NHTSA on July 5, 2022, and 
amended the petition on August 4, 2022, for a decision that the subject 
noncompliance is inconsequential as it relates to motor vehicle safety. 
This document announces receipt of CTP's petition.

DATES: Send comments on or before September 26, 2022.

ADDRESSES: Interested persons are invited to submit written data, 
views, and arguments on this petition. Comments must refer to the 
docket and notice number cited in the title of this notice and may be 
submitted by any of the following methods:
     Mail: Send comments by mail addressed to the U.S. 
Department of Transportation, Docket Operations, M-30, West Building 
Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 
20590.
     Hand Delivery: Deliver comments by hand to the U.S. 
Department of Transportation, Docket Operations, M-30, West Building 
Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 
20590. The Docket Section is open on weekdays from 10 a.m. to 5 p.m. 
except for Federal Holidays.
     Electronically: Submit comments electronically by logging 
onto the Federal Docket Management System (FDMS) website at https://www.regulations.gov/. Follow the online instructions for submitting 
comments.
     Comments may also be faxed to (202) 493-2251.
    Comments must be written in the English language, and be no greater 
than 15 pages in length, although there is no limit to the length of 
necessary attachments to the comments. If comments are submitted in 
hard copy form, please ensure that two copies are provided. If you wish 
to receive confirmation that comments you have submitted by mail were 
received, please enclose a stamped, self-addressed postcard with the 
comments. Note that all comments received will be posted without change 
to https://www.regulations.gov, including any personal information 
provided.
    All comments and supporting materials received before the close of 
business on the closing date indicated above will be filed in the 
docket and will be considered. All comments and supporting materials 
received after the closing date will also be filed and will be 
considered to the fullest extent possible.
    When the petition is granted or denied, notice of the decision will 
also be published in the Federal Register pursuant to the authority 
indicated at the end of this notice.
    All comments, background documentation, and supporting materials 
submitted to the docket may be viewed by anyone at the address and 
times given above. The documents may also be viewed on the internet at 
https://www.regulations.gov by following the online instructions for 
accessing the dockets. The docket ID number for this petition is shown 
in the heading of this notice.
    DOT's complete Privacy Act Statement is available for review in a 
Federal Register notice published on April 11, 2000 (65 FR 19477-78).

FOR FURTHER INFORMATION CONTACT: Kelley Adams-Campos, Safety Compliance 
Engineer, NHTSA, Office of Vehicle Safety Compliance, 
[email protected], (202) 366-7479.

SUPPLEMENTARY INFORMATION: 
    I. Overview: CTP has determined that certain child restraint 
systems manufactured under the brand name CYBEX and distributed by CTP 
do not fully comply with paragraph S5.4.1.2(b)(1) of FMVSS No. 213, 
Child Restraint Systems (49 CFR 571.213). CTP filed an original 
noncompliance report dated June 30, 2022, pursuant to 49 CFR part 573, 
Defect and Noncompliance Responsibility and Reports. CTP petitioned 
NHTSA on July 5, 2022, and amended the petition on August 4, 2022, for 
an exemption from the notification and remedy requirements of 49 U.S.C. 
chapter 301 on the basis that this noncompliance is inconsequential as 
it relates to motor vehicle safety, pursuant to 49 U.S.C. 30118(d) and 
30120(h) and 49 CFR part 556, Exemption for Inconsequential Defect or 
Noncompliance.
    This notice of receipt of CTP's petition is published under 49 
U.S.C. 30118 and 30120 and does not represent any agency decision or 
other exercise of judgment concerning the merits of the petition.
    II. Child Restraint Systems Involved: Approximately 31,080 Aton M, 
Aton 2, Aton, Aton Q, and Cloud Q model child restraint systems 
manufactured by CYBEX approximately between June 6, 2017,\1\ and 
November 1, 2020, are potentially involved.
---------------------------------------------------------------------------

    \1\ In its June 30, 2022, Part 573 submission, CTP reported 
production dates between March 7, 2017 and November 1, 2020.
---------------------------------------------------------------------------

    III. Rule Requirements: Paragraphs S5.4.1.2(a) and S5.4.1.2(b)(1) 
of FMVSS No. 213 include the requirements relevant to this petition. 
The webbing of belts provided with a child restraint system which are 
used to restrain the child within the system shall, after being 
subjected to abrasion as specified in S5.1(d) or S5.3(c) of FMVSS No. 
209 (Sec.  571.209), have a breaking strength of

[[Page 52615]]

not less than 75 percent of the new webbing strength when tested in 
accordance with S5.1(b) of FMVSS No. 209. ``New webbing'' means webbing 
that has not been exposed to abrasion, light, or micro-organisms as 
specified elsewhere in FMVSS No. 213.
    IV. Noncompliance: After being subjected to abrasion, the breaking 
strength of the adjuster webbing on the subject child restraint systems 
was less than 75 percent of the new webbing strength as required by 
S5.4.1.2(b)(1) of FMVSS No. 213.
    V. Summary of CTP's Petition: CTP explains that the adjuster 
webbing retained only 56.9 percent of the new webbing strength 
following the hex bar abrasion test \2\ as specified in S5.1(d) of 
FMVSS No. 209.\3\ CTP also acknowledges the noncompliance based on the 
``through-adjuster'' \4\ test methodology it employed towards 
satisfying S5.3(c) of FMVSS No. 209. The views and arguments provided 
by CTP are presented in this section, ``V. Summary of CTP's Petition.'' 
They have not been evaluated by the Agency and do not reflect the views 
of the Agency. CTP describes the subject noncompliance and contends 
that the noncompliance is inconsequential as it relates to motor 
vehicle safety.
---------------------------------------------------------------------------

    \2\ OVSC compliance test report available at https://static.nhtsa.gov/odi/ctr/9999/TRTR-647389-2020-001.pdf.
    \3\ In its petition, CTP mistakenly referred to FMVSS No. 209 as 
FMVSS No. 213.
    \4\ In its petition, CTP refers to S5.3(c) of FMVSS No. 209 
Resistance to buckle abrasion as through-adjuster test.
---------------------------------------------------------------------------

    After receiving a July 2021 Information Request from NHTSA relating 
to this noncompliance, CTP, together with its supplier Holmbergs, took 
certain investigative actions, including reviewing prior test results. 
CTP learned that Holmbergs did not have any historical test data for 
the hex bar or its through-adjuster abrasion testing pursuant to FMVSS 
No. 213 S5.4.1.2(b)(1).\5\ CTP retained webbing samples from 2018 
central adjuster webbing production that would have been used on the 
(US) Aton M child restraint systems and conducted testing on them, 
``pursuant to FMVSS 213, Sec.  5.4.1.2(b)(1).'' The results from this 
testing were that the webbing abraded using the hex bar test subceeded 
the required 75 percent of the new webbing breaking strength, averaging 
64 percent, and the webbing abraded using CTP's through-adjuster test 
exceeded the required 75 percent of the new webbing breaking strength. 
CTP shared the results with NHTSA, submitting that FMVSS No. 213 
S5.4.1.2(b)(1) provides two alternative abrasion test compliance 
options. The first, as provided in FMVSS No. 209 S5.1(d), (hex bar 
test) and the second, as provided in FMVSS No. 209 S5.3(c), (through-
adjuster test). CTP explains that in its investigation, NHTSA concluded 
that CTP's through-adjuster test methods were not an appropriate 
interpretation of FMVSS No. 209 S5.3(c). CTP acknowledges the 
noncompliances with S5.1(d) and S5.3(c) of FMVSS No. 209, and outlines 
its rationale for why ``any noncompliance'' is inconsequential to child 
safety.
---------------------------------------------------------------------------

    \5\ In section 2 of its petition, CTP mistakenly referred to 
S5.4.1.2(b)(1) of FMVSS No. 213 as S5.4.2.1(b)(1).
---------------------------------------------------------------------------

    CTP believes that the subject noncompliance with the hex bar test 
is inconsequential to motor vehicle safety based on results from 
overload dynamic crash tests it conducted on CYBEX Aton M child 
restraints assembled using abraded adjuster webbing from the samples 
averaging 64 percent retained breaking strength. CTP asserts that 
because the adjuster webbing loads in the dynamic tests were only a 
small fraction (11 percent) of the abraded webbing's retained strength, 
a significant safety margin is built into the central adjuster webbing 
making it ``sufficient for this application,'' (Aton M and similar). 
This difference, CTP explains, shows that significantly more 
degradation (of webbing strength) could be tolerated. According to 
internal crash test data collected from tests varying in configuration, 
ATDs, attachment methods and crash severities, CTP states that the peak 
central adjuster strap load recorded was 4745 N. CTP also states that 
the dynamic crash tests of the child restraints with the hex bar 
abraded webbing showed that structural integrity of the child restraint 
was maintained and that the occupant was retained.
    CTP notes that NHTSA's laboratory test procedure for FMVSS No. 209 
Seat Belt Assemblies \6\ ``specifies that for webbing resistance to 
abrasion tests performed pursuant to FMVSS Sec.  4.2(d), 5.1(d), and 
5.3(c) the assembly ``shall be subjected to the buckle abrasion test'' 
if the ``assembly contain [sic] a manual adjusting device'' with the 
emphasis applied, and explains its methodology for the through-adjuster 
testing it employed. FMVSS No. 209 S5.3(c) Resistance to buckle 
abrasion, requires, CTP states in part, that ``[t]he webbing shall be 
pulled back and forth through the buckle or manual adjusting device as 
shown schematically in Figure 7 . . .'' and ``[t]he webbing shall pass 
through the buckle. . .'' with the emphases applied. CTP contends that 
the referenced schematic in Figure 7 of Standard No. 209 ``should only 
be viewed as a general visual aid,'' and that the schematic 
``contradict[s] the plain language of the FMVSS.'' CTP states that 
although the schematic (in Figure 7 of Standard No. 209) does not 
appear to show the buckle or adjusting device opening and closing, 
``that action certainly must occur to meet the plain language and clear 
intent of the regulation.'' When CTP performed its through-adjuster 
testing on the 2018 production retained webbing samples, the webbing 
was cycled through the central adjuster containing a cam lock. CTP 
states that the cam lock ``must be opened during the lengthening 
stroke'' otherwise the adjuster will ``not allow webbing to move,'' 
i.e., pass through it. CTP investigated a variety of test conditions 
related to FMVSS No. 209 S5.3(c) ``varying the amount and timing of the 
central adjuster cam opening'' in each. CTP believes the through-
adjuster abrasion test it used accurately exposes the webbing to the 
abrading environment that exists in the real-world application. 
Nonetheless, CTP acknowledges the noncompliance of the central adjuster 
webbing using its test methodology, submitting it too is 
inconsequential ``as the language of the regulation, as well as the 
stated purpose of the regulation, should control the test methodology 
employed.''
---------------------------------------------------------------------------

    \6\ Dated December 7, 2007.
---------------------------------------------------------------------------

    Holmbergs provided to CTP evidence of its internal procedures and 
control plans designed to ensure all regulatory requirements are 
satisfied. CTP's Quality Management System (QMS) requires review and 
acceptance of Holmbergs' Control Plan prior to supplying the subject 
webbing to CTP. CTP explains it ``relies on its suppliers to self-
certify compliance to certain standards and requirements'' and that 
Holmbergs ``was following the Aton M US Control Plan'' based on CTP's 
On-going Quality Control (OQC) reports. CTP provided the Control Plan, 
OQC and other documents in its April 14, 2022, supplemental response to 
NHTSA.
    CTP claims it has implemented replacement central adjuster webbing 
on new child restraints manufactured beginning October 27, 2021, and 
that this webbing complies with all retained tensile strength 
requirements after having been subject to both hex bar and through-
adjuster testing. Additionally, CTP states it has clarified to its 
webbing supplier that the supplied webbing must comply with both 
available abrasion tests in its specificiations. Finally, CTP states 
that since 2017 no central adjuster webbing or central adjuster 
assembly issues have been observed.

[[Page 52616]]

    Details of CTP's investigation and testing can be found in its 
amended petition at https://www.regulations.gov/document/NHTSA-2022-0065-0001.
    CTP concludes by stating its belief that the subject noncompliance 
is inconsequential as it relates to motor vehicle safety and its 
petition to be exempted from providing notification of the 
noncompliance, as required by 49 U.S.C. 30118, and a remedy for the 
noncompliance, as required by 49 U.S.C. 30120, should be granted.
    NHTSA notes that the statutory provisions (49 U.S.C. 30118(d) and 
30120(h)) that permit manufacturers to file petitions for a 
determination of inconsequentiality allow NHTSA to exempt manufacturers 
only from the duties found in sections 30118 and 30120, respectively, 
to notify owners, purchasers, and dealers of a defect or noncompliance 
and to remedy the defect or noncompliance. Therefore, any decision on 
this petition only applies to the subject child restraints that CTP no 
longer controlled at the time it determined that the noncompliance 
existed. However, any decision on this petition does not relieve child 
restraint distributors and dealers of the prohibitions on the sale, 
offer for sale, or introduction or delivery for introduction into 
interstate commerce of the noncompliant child restraints under their 
control after CTP notified them that the subject noncompliance existed.

(Authority: 49 U.S.C. 30118, 30120: delegations of authority at 49 
CFR 1.95 and 501.8)

Otto G. Matheke III,
Director, Office of Vehicle Safety Compliance.
[FR Doc. 2022-18417 Filed 8-25-22; 8:45 am]
BILLING CODE 4910-59-P


