[Federal Register Volume 85, Number 218 (Tuesday, November 10, 2020)]
[Notices]
[Pages 71713-71717]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-24866]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

National Highway Traffic Safety Administration

[Docket No. NHTSA-2017-0097; Notice 2]


General Motors, LLC, Denial of Petition for Decision of 
Inconsequential Noncompliance

AGENCY: National Highway Traffic Safety Administration (NHTSA), U.S. 
Department of Transportation (DOT).

ACTION: Denial of petition.

-----------------------------------------------------------------------

SUMMARY: General Motors, LLC (GM), has determined that the seat belt 
assemblies in certain model year (MY) 2017-2018 Chevrolet Silverado 
heavy duty and GMC Sierra heavy duty motor vehicles do not fully comply 
with Federal Motor Vehicle Safety Standard (FMVSS) No. 209, Seat Belt 
Assemblies. GM filed a noncompliance report dated September 14, 2017, 
and later amended it on September 22, 2017. GM also petitioned NHTSA on 
October 6, 2017, for a decision that the subject noncompliance is 
inconsequential as it relates to motor vehicle safety. This document 
announces the denial of GM's petition.

FOR FURTHER INFORMATION CONTACT: Mr. Stephen Hench, Office of Chief 
Counsel, telephone 202-366-2262, facsimile 202-366-3820, or Mr. Jack 
Chern, Office of Vehicle Safety Compliance, NHTSA, telephone 202-366-
0661, facsimile 202-366-3081.

SUPPLEMENTARY INFORMATION:

I. Overview:

    GM has determined that the seat belt assemblies in certain MY 2017-
2018 Chevrolet Silverado heavy duty and GMC Sierra heavy duty motor 
vehicles do not fully comply with paragraphs S4.4(b)(5) of FMVSS No. 
209, Seat Belt Assemblies (49 CFR 571.209). GM filed a noncompliance 
report dated September 14, 2017, and amended it on September 22, 2017, 
pursuant to 49 CFR part 573, Defect and Noncompliance Responsibility 
and Reports. GM also petitioned NHTSA on October 6, 2017, for an 
exemption from the notification and remedy requirements of 49 U.S.C. 
Chapter 301 on the basis that this noncompliance is inconsequential as 
it relates to motor vehicle safety, pursuant to 49 U.S.C. 30118(d) and 
30120(h) and 49 CFR part 556, Exemption for Inconsequential Defect or 
Noncompliance.
    Notice of receipt of GM's petition was published, with a 30-day 
public comment period, on January 10, 2018, in the Federal Register (83 
FR 1282). No comments were received. To view the petition and all 
supporting documents, log onto the Federal Docket Management System 
(FDMS) website at: http://www.regulations.gov/. Then follow the online 
search instructions to locate docket number ``NHTSA-2017-0097.''

II. Vehicles Involved

    This petition concerns approximately 38,048 MY 2017-2018 Chevrolet 
Silverado heavy duty and GMC Sierra heavy duty (Gross Vehicle Weight 
Rating (GVWR) of 9,300-13,400 lbs) motor vehicles, manufactured between 
July 18, 2016, and August 7, 2017. The double cab versions of the 
subject vehicles are not included in this petition.

III. Noncompliance

    GM explains the noncompliance as seat belt assemblies that do not 
conform to the upper-torso seat belt elongation requirements specified 
in paragraph S4.4(b)(5) of FMVSS No. 209. Specifically, the seat belt 
assemblies were built with load-limiting torsion bars measuring 9.5 mm 
in diameter on the driver side and 8.0 mm on the passenger side, 
instead of 12 mm for both sides as specified by GM.

[[Page 71714]]

IV. Rule Requirements

    Paragraph S4.4(b)(5) of FMVSS No. 209, includes the requirements 
relevant to this petition. Except as provided in paragraph S4.5 of 
FMVSS No. 209, when tested by the procedure specified in paragraph 
S5.3(b), the length of the upper torso restraint between anchorages 
shall not increase more than 508 mm when subjected to a force of 11,120 
N.

V. Summary of GM's Petition

    GM stated that smaller diameter torsion bars in the noncompliant 
trucks are regularly used in retractor assemblies in other full-size 
trucks, including variants of the subject vehicles. Due to their 
smaller size and weight rating, these similar variants are subject to 
S5.1 of FMVSS No. 208, and exempt from S4.4(b)(5) of FMVSS No. 209.\1\ 
GM contends that the seat belt retractors with undersized torsion bars 
inadvertently installed in the subject vehicles provide at least the 
same level of occupant protection in frontal crashes while optimizing 
belt force-deflection characteristics. However, the subject vehicles 
were not certified to S5.1 of FMVSS No. 208 and, accordingly, were not 
intended to be equipped with these smaller diameter torsion bars 
because they were required to meet the elongation requirements of 
S4.4(b)(5) of FMVSS No. 209.
---------------------------------------------------------------------------

    \1\ S4.5 of FMVSS No. 209 exempts load-limited seat belts 
installed at a designated seating position subject to S5.1 of FMVSS 
No. 208 from the elongation requirements.
---------------------------------------------------------------------------

    GM described the subject noncompliance and stated its belief that 
the noncompliance is inconsequential as it relates to motor vehicle 
safety. In support of its petition, GM submitted the following 
reasoning:

1. GM Indicates the Subject Vehicles Meet the Belted Frontal Crash 
Performance Testing Requirements of S5.1 of FMVSS No. 208

    GM has conducted dynamic frontal crash testing on 2500 series 
vehicles that it describes as substantially similar to the subject 
vehicles and equipped with the same load-limiting seat belt retractors 
with the lower-diameter torsion bars (the ``Tested Vehicles'').\2\ 
According to GM, the tested vehicles comply with the belted frontal 
crash performance testing requirements under S5.1.1(a) of FMVSS No. 
208.\3\ The petition also states that the tested vehicles performed 
below the injury assessment reference limits specified in S5.1.1(a) 
even when tested at 35 mph, which subjects the vehicle to 36 percent 
more energy than at the 30 mph testing standard provided in the 
regulation. GM contends that the tested vehicles were also rated by 
NHTSA with an overall 4-Star NCAP score.
---------------------------------------------------------------------------

    \2\ The subject vehicles and tested vehicles share the same 
frame, body structure, powertrains and under-hood crush space; 
instrument panel, steering column and wheel, seats, seat-belt 
anchorages, and general interior vehicle layout/spatial 
relationships; and driver and passenger frontal airbags. In similar 
configurations, the subject vehicles and test vehicles have similar 
mass.
    \3\ S5.1.1(a) of FMVSS No. 208 specifies the belted barrier test 
requirements for certain vehicles not certified to S14 of FMVSS No. 
208 (i.e., those with a GVW >8,500 lbs. or an unloaded weight >5,500 
lbs).
---------------------------------------------------------------------------

    GM expects that the subject vehicles will perform nearly the same 
as the tested vehicles in dynamic frontal crash testing and would 
therefore also meet all of the belted barrier test requirements 
specified by S5.1.1(a) of FMVSS No. 208.
    GM cites statements made by NHTSA in prior rulemaking notices \4\ 
to support its position that the dynamic belted frontal barrier crash 
testing of S5.1.1(a) of FMVSS No. 208 is a more appropriate means to 
evaluate occupant protection than the static seat belt elongation 
testing requirements of S4.4(b)(5) of FMVSS No. 209 for vehicles with 
seat belts equipped with load limiters.
---------------------------------------------------------------------------

    \4\ In its 1991 rulemaking modifying FMVSS No. 209 to exclude 
certain dynamically tested seat belts from some of the static seat-
belt testing requirements, NHTSA acknowledged that it ``has long 
believed it more appropriate to evaluate the occupant protection 
afforded by vehicles by conducting dynamic testing . . .'' versus 
static tests such as the elongation requirements in S4.4(b)(5) of 
FMVSS No. 209. Final Rule, 56 FR 15295, 15295 (April 16, 1991). 
Further, ``[s]ince the dynamic test measures the actual occupant 
protection which the belt provides during a crash, there is no 
apparent need to subject that belt to static testing procedures that 
are surrogate and less direct measures of the protection which the 
belt would provide to its occupant during a crash.'' Notice of 
Proposed Rulemaking, 55 FR 1681 (January 18, 1990). GM believes 
NHTSA's rationale for creating these exemptions applies to the 
subject vehicles even though they may not all technically be 
``subject to'' S5.1 of FMVSS No. 208 and therefore exempt from FMVSS 
No. 209's elongation requirements.
---------------------------------------------------------------------------

2. GM Believes the Subject Vehicles Will Provide No Less Protection to 
Occupants in a Frontal Crash Than Vehicles Equipped With Seat Belt 
Retractors Utilizing the 12 mm Torsion Bars

    GM believes that replacing the retractors installed in the subject 
vehicles with retractors that have the larger torsion bars would not 
result in an added safety benefit to the occupants of these vehicles in 
frontal crashes. The petition contends that the subject vehicles will 
provide no less occupant protection than vehicles built with the larger 
12 mm diameter torsion bars that meet the elongation requirements of 
S4.4(b)(5) of FMVSS No. 209. Further, GM states that seat belt 
retractors equipped with the lower-diameter torsion bars may reduce 
upper torso injury potential in frontal crashes as compared to 
retractors with the larger-diameter torsion bars.

3. GM Believes NHTSA Precedent Supports Granting the Petition

    GM states that NHTSA has previously ruled that failure to comply 
with certain FMVSS No. 209 static testing requirements can be 
inconsequential to motor vehicle safety, where the manufacturer 
demonstrates by dynamic testing that the noncompliant seat belt 
assembly performs similarly to a compliant assembly. On May 3, 2002, GM 
submitted an inconsequentiality petition to NHTSA relating to certain 
trucks and SUVs that were built with damaged and inoperative ``vehicle-
sensitive'' emergency-locking retractors (ELRs), which lock the seat 
belts under rapid deceleration. Notwithstanding the noncompliance with 
FMVSS No. 209 caused by this condition, GM asserted that the failure 
was inconsequential to vehicle safety because the ELRs in these 
vehicles also had a redundant ``webbing-sensitive'' mechanism, which 
locks the belts when the webbing is rapidly extracted. GM contends it 
presented dynamic testing data (including some data developed using the 
test procedures set forth in FMVSS No. 208) demonstrating that the 
webbing-sensitive system ``offered a level of protection nearly 
equivalent to that provided by a compliant ELR.''
    GM states that NHTSA granted GM's petition, in part, and ruled the 
noncompliance in certain of the vehicles subject to the petition was 
inconsequential to motor vehicle safety:

    On the basis of the sled test and simulation data provided by 
GM, the agency has concluded that GM has adequately demonstrated 
that the potential safety consequences of the failure of the 
vehicle-sensitive locking mechanisms in the ELRs in the C/K vehicles 
to function properly are inconsequential. While the webbing-
sensitive systems in these vehicles do allow slightly increased belt 
payout compared to a functional vehicle-sensitive system, and lock 
slightly later in crash event, these differences do not appear to 
expose a vehicle occupant to a significantly greater risk of injury.

    General Motors Corporation, Ruling on Petition for Determination of 
Inconsequential Noncompliance, 69 FR 19897, 19900 (April 14, 2004). In 
its decision, NHTSA also noted that ``the dummy injury measurements did 
not increase significantly and were well below the maximum values 
permitted under FMVSS No. 208.''

[[Page 71715]]

    Here, GM argues that the subject vehicles will provide no less 
protection to occupants in the designated seating positions in frontal 
crashes than vehicles equipped with seat belt retractors conforming to 
S4.4(b)(5) of FMVSS No. 209.

4. GM Is Not Aware of any Injuries or Customer Complaints Associated 
With the Condition

    As of September 22, 2017, after searching VOQ, TREAD and internal 
GM databases, GM stated it was not aware of any crashes, injuries, or 
customer complaints associated with this condition.

5. GM Has Corrected the Noncompliance in Production Vehicles and 
Service Part Inventory

    GM states that it has corrected the noncompliance in production. 
According to GM, vehicles produced after August 7, 2017, have seat belt 
assemblies containing retractor torsion bars that meet GM's original 
specifications and comply with S4.4(b)(5) of FMVSS No. 209. The 
petition also states that retractor assemblies with this condition that 
were manufactured as service parts are no longer available for sale and 
all affected inventory has been purged. Further, GM contends that any 
such seat belt assembly previously sold as a service part could only 
have been installed on a subject vehicle because these seat belt 
assemblies are not compatible with prior model year (i.e., 2015 or 
2016) versions of the Silverado or Sierra HD, due to a different type 
of wiring connector used.
    GM concludes by expressing the belief that the subject 
noncompliance is inconsequential as it relates to motor vehicle safety, 
and that its petition to be exempted from providing notification of the 
noncompliance, as required by 49 U.S.C. 30118, and a remedy for the 
noncompliance, as required by 49 U.S.C. 30120, should be granted.

VI. NHTSA's Analysis

1. General Principles

    Congress passed the National Traffic and Motor Vehicle Safety Act 
of 1966 (the ``Safety Act'') with the express purpose of reducing motor 
vehicle accidents, deaths, injuries, and property damage. 49 U.S.C. 
30101. To this end, the Safety Act empowers the Secretary of 
Transportation to establish and enforce mandatory FMVSS 49 U.S.C. 
30111. The Secretary has delegated this authority to NHTSA. 49 CFR 
1.95.
    NHTSA adopts an FMVSS only after the agency has determined that the 
performance requirements are objective, practicable, and meet the need 
for motor vehicle safety. See 49 U.S.C. 30111(a). Thus, there is a 
general presumption that the failure of a motor vehicle or item of 
motor vehicle equipment to comply with an FMVSS increases the risk to 
motor vehicle safety beyond the level deemed appropriate by NHTSA 
through the rulemaking process. To protect the public from such risks, 
manufacturers whose products fail to comply with an FMVSS are normally 
required to conduct a safety recall under which they must notify 
owners, purchasers, and dealers of the noncompliance and provide a free 
remedy. 49 U.S.C. 30118-30120. However, Congress has recognized that, 
under some limited circumstances, a noncompliance could be 
``inconsequential'' to motor vehicle safety. It, therefore, established 
a procedure under which NHTSA may consider whether it is appropriate to 
exempt a manufacturer from its notification and remedy (i.e., recall) 
obligations. 49 U.S.C. 30118(d) & 30120(h). The agency's regulations 
governing the filing and consideration of petitions for 
inconsequentiality exemptions are set out at 49 CFR part 556.
    Under the Safety Act and Part 556, inconsequentiality exemptions 
may be granted only in response to a petition from a manufacturer, and 
then only after notice in the Federal Register and an opportunity for 
interested members of the public to present information, views, and 
arguments on the petition. In addition to considering public comments, 
the agency will draw upon its own understanding of safety-related 
systems and its experience in deciding the merits of a petition. An 
absence of opposing argument and data from the public does not require 
NHTSA to grant a manufacturer's petition.
    Neither the Safety Act nor Part 556 defines the term 
``inconsequential.'' The agency determines whether a particular 
noncompliance is inconsequential to motor vehicle safety based upon the 
specific facts before it in a particular petition. In some instances, 
NHTSA has determined that a manufacturer met its burden of 
demonstrating that a noncompliance is inconsequential to safety. For 
example, a label intended to provide safety advice to an owner or 
occupant may have a misspelled word, or it may be printed in the wrong 
format or the wrong type size. Where a manufacturer has shown that the 
discrepancy with the safety requirement should not lead to any 
misunderstanding, NHTSA has granted an inconsequentiality exemption, 
especially where other sources of correct information are available. 
See, e.g., General Motors, LLC, Grant of Petition for Decision of 
Inconsequential Noncompliance, 81 FR 92963 (Dec. 20, 2016).
    The burden of establishing the inconsequentiality of a failure to 
comply with a performance requirement in a standard--as opposed to a 
labeling requirement--is more substantial and difficult to meet. 
Accordingly, the Agency has not found many such noncompliances 
inconsequential.\5\ Potential performance failures of safety-critical 
equipment, like seat belts or air bags, are rarely deemed 
inconsequential.
---------------------------------------------------------------------------

    \5\ Cf. Gen. Motors Corporation; Ruling on Petition for 
Determination of Inconsequential Noncompliance, 69 FR 19897, 19899 
(Apr. 14, 2004) (citing prior cases where noncompliance was expected 
to be imperceptible, or nearly so, to vehicle occupants or 
approaching drivers).
---------------------------------------------------------------------------

    An important issue to consider in determining inconsequentiality 
based upon NHTSA's prior decisions on noncompliance issues was the 
safety risk to individuals who experience the type of event against 
which the recall would otherwise protect.\6\ NHTSA also does not 
consider the absence of complaints or injuries to show that the issue 
is inconsequential to safety. ``Most importantly, the absence of a 
complaint does not mean there have not been any safety issues, nor does 
it mean that there will not be safety issues in the future.'' \7\ 
``[T]he fact that in past reported cases good luck and swift reaction 
have prevented many serious injuries does not mean that good luck will 
continue to work.'' \8\
---------------------------------------------------------------------------

    \6\ See Gen. Motors, LLC; Grant of Petition for Decision of 
Inconsequential Noncompliance, 78 FR 35355 (June 12, 2013) (finding 
noncompliance had no effect on occupant safety because it had no 
effect on the proper operation of the occupant classification system 
and the correct deployment of an air bag); Osram Sylvania Prods. 
Inc.; Grant of Petition for Decision of Inconsequential 
Noncompliance, 78 FR 46000 (July 30, 2013) (finding occupant using 
noncompliant light source would not be exposed to significantly 
greater risk than occupant using similar compliant light source).
    \7\ Morgan 3 Wheeler Limited; Denial of Petition for Decision of 
Inconsequential Noncompliance, 81 FR 21663, 21666 (Apr. 12, 2016).
    \8\ United States v. Gen. Motors Corp., 565 F.2d 754, 759 (D.C. 
Cir. 1977) (finding defect poses an unreasonable risk when it 
``results in hazards as potentially dangerous as sudden engine fire, 
and where there is no dispute that at least some such hazards, in 
this case fires, can definitely be expected to occur in the 
future'').
---------------------------------------------------------------------------

    Arguments that only a small number of vehicles or items of motor 
vehicle equipment are affected have also not justified granting an 
inconsequentiality petition.\9\ Similarly, NHTSA has

[[Page 71716]]

rejected petitions based on the assertion that only a small percentage 
of vehicles or items of equipment are likely to actually exhibit a 
noncompliance. The percentage of potential occupants that could be 
adversely affected by a noncompliance does not determine the question 
of inconsequentiality. Rather, the issue to consider is the consequence 
to an occupant who is exposed to the consequence of that 
noncompliance.\10\ These considerations are also relevant when 
considering whether a defect is inconsequential to motor vehicle 
safety.
---------------------------------------------------------------------------

    \9\ See Mercedes-Benz, U.S.A., L.L.C.; Denial of Application for 
Decision of Inconsequential Noncompliance, 66 FR 38342 (July 23, 
2001) (rejecting argument that noncompliance was inconsequential 
because of the small number of vehicles affected); Aston Martin 
Lagonda Ltd.; Denial of Petition for Decision of Inconsequential 
Noncompliance, 81 FR 41370 (June 24, 2016) (noting that situations 
involving individuals trapped in motor vehicles--while infrequent--
are consequential to safety); Morgan 3 Wheeler Ltd.; Denial of 
Petition for Decision of Inconsequential Noncompliance, 81 FR 21663, 
21664 (Apr. 12, 2016) (rejecting argument that petition should be 
granted because the vehicle was produced in very low numbers and 
likely to be operated on a limited basis).
    \10\ See Gen. Motors Corp.; Ruling on Petition for Determination 
of Inconsequential Noncompliance, 69 FR 19897, 19900 (Apr. 14, 
2004); Cosco Inc.; Denial of Application for Decision of 
Inconsequential Noncompliance, 64 FR 29408, 29409 (June 1, 1999).
---------------------------------------------------------------------------

Response to GM's Arguments
    NHTSA has considered GM's arguments and determined that the load-
limiting retractor installed with torsion bars measuring 9.5 mm in 
diameter on the driver side and 8.0 mm on the passenger side, instead 
of 12 mm as specified by GM, is not inconsequential to motor vehicle 
safety. NHTSA, therefore, denies GM's request for an inconsequentiality 
determination, for the following reasons:
a. NHTSA Does Not Find the Dynamic Testing of Similar Vehicles 
Compelling in This Case
    GM believes that the noncompliance of load limiters, mistakenly 
installed with torsion bars measuring 9.5 and 8.0 mm in diameter on the 
driver and passenger side instead of 12 mm as specified by GM, is 
inconsequential to motor vehicle safety. A load limiter is a seat belt 
assembly component that controls tension on the seat belt and modulates 
the forces imparted to a vehicle occupant during a crash. Load limiters 
are intended primarily to reduce upper torso injuries caused by the 
compressive force applied by the relatively narrow seat belt. They may 
work in concert with an air bag system to optimize occupant protection 
in a crash and provide overall crash energy management. Section S4.5 of 
FMVSS No. 209 exempts a belt with a load limiter from the standard's 
elongation requirements if it is installed at a seating position 
subject to the requirements of S5.1 of Standard No. 208--that is, 
``subject to'' a belted crash test specified in FMVSS No. 208.
    GM argues that the crash testing it performed on the 2500 series 
vehicles that were substantially similar to the subject vehicles and 
were equipped with the same load-limiting seat belt retractors with the 
lower-diameter torsion bars shows that the noncompliant seat belts in 
the subject vehicles will provide no less protection to occupants in 
the designated seating positions in frontal crashes than vehicles 
equipped with seat belt retractors conforming to S4.5 of FMVSS No. 209. 
GM also cites a prior grant of an inconsequentiality petition for 
certain of the FMVSS No. 209 static requirements based, in part, on 
dynamic test data.
    The agency disagrees with GM's assessment. NHTSA has more recently 
considered this issue, its putative inconsequentiality, and whether 
testing supporting compliance with FMVSS No. 208 may support finding a 
noncompliance with FMVSS No. 209 inconsequential. See BMW of North 
America, LLC; Jaguar Land Rover North America, LLC; and Autoliv, Inc.; 
Decisions of Petitions for Inconsequential Noncompliance, 84 FR 19994 
(May 7, 2019). In any case, the petition cited by GM as precedent, 
General Motors Corporation, Ruling on Petition for Determination of 
Inconsequential Noncompliance, 69 FR 19897, 19900 (April 14, 2004), 
concerns a different requirement in FMVSS No. 209: Lock up within 25 mm 
versus elongation. The petition states that ``GM expects that the 
Subject Vehicles will perform nearly the same as the Tested Vehicles in 
dynamic frontal crash testing, and would therefore also meet all of the 
belted barrier test requirements specified by S5.1.1 (a) of FMVSS No. 
208.'' However, whether the subject vehicles would be capable of 
meeting the test requirements of FMVSS No. 208 S5.1.1(a) is not at 
issue. This is not a compliance requirement or option for the front 
outboard seats in the subject vehicles. Rather, the issue is whether 
the subject vehicles' noncompliance with FMVSS No. 209 S4.4(b)(5) is 
inconsequential to safety. We do not agree that the test results for 
the tested vehicles are sufficient for this showing. We explain our 
reasoning below.
    The subject vehicles were neither subject to, nor tested to, 
S5.1.1(a) of FMVSS No. 208. GM contends, however, that the belted 
frontal barrier impact data used to certify compliance of certain 
variants of the 2500 vehicles is a valid surrogate for the subject 
vehicles with the smaller diameter torsion bars. GM indicated that the 
tested vehicles were ``substantially similar'' to the subject vehicles. 
However, a simple examination of the GVWR comparison between the two 
sets of vehicles indicates that this is a questionable conclusion. The 
tested vehicles were 2500 series and the subject vehicles were 2500, 
3500, and 3600 series. As reported by GM, the 2500 series have a GVWR 
range of 9,300-10,000 lbs. The 3500 and 3600 are encompassed in a GVWR 
range of 10,000-13,400 lbs.
    GM's argument seems to be predicated on the assumption that if the 
subject vehicles were tested using the FMVSS No. 208 procedure, the 
tested weight of the subject vehicles would be similar to the tested 
weight of the tested vehicles. We have no reason to believe that GM has 
not optimized the sharing of the occupant restraint contribution from 
the seat belt for the tested vehicles to the parameters required by the 
FMVSS No. 208 barrier impacts. However, just as important for the 
agency's consideration of this issue is the difference in the GVWR 
range for the subject and tested vehicles. GM contends that ``[t]he 
primary difference between the Subject Vehicles and Tested Vehicles is 
that the Subject Vehicles have increased capacity suspension 
components, which do not affect the vehicles' crash performance.'' This 
statement seems to ignore that with these differences in the subject 
vehicles comes the much greater GVWR range of subject vehicles compared 
to the tested vehicles. With this much greater fully loaded mass would 
potentially come much different frontal crash dynamics.
    Although GM states the subject and tested vehicles share many of 
the same structural components related to crash energy management, the 
fact remains that the subject vehicles may require much more energy to 
be managed because of the GVWR differences. For example, it could be 
theorized that this additional mass may extend the crash pulse 
duration. Similarly, managing this additional energy could mean 
additional vehicle crush, essentially changing the shape of the crash 
pulse. Differences in pulse shape and duration may change the optimal 
sharing of restraint between the seat belt and air bag. This change in 
crash pulse may also affect the air bag deployment timing.
    In summary, we are not convinced that the crash test data provided 
in the GM submission is sufficient to show that the smaller torsion bar 
placed in the

[[Page 71717]]

subject vehicles would be inconsequential to safety. In real-world 
frontal crashes, with subject vehicles loaded near the GVWR, we believe 
the crash pulse duration and shape may differ from what would be seen 
in an FMVSS No. 208 frontal barrier test, affecting the optimization of 
the occupant restraint system that includes the lower diameter torsion 
bars in the seat belt load limiters.
    More generally, GM's assessment also ignores the crucial role that 
the static testing requirements of FMVSS No. 209 play in acting as a 
safety backstop for crash scenarios that are not accounted for in 
dynamic tests such as those conducted by GM. Dynamic tests are meant to 
assess whether a vehicle's occupant protection systems work cohesively 
in certain representative crashes. However, there are countless crash 
and pre-crash scenarios that these sorts of tests do not cover, which 
is why static requirements of FMVSS No. 209 are intended to ``fill in 
the gaps'' to ensure that the vehicle's seat belt equipment maintains a 
minimum level of performance in untested scenarios.
    For example, dynamic tests do not account for the fact that a seat 
belt assembly is intended to protect occupants even when they are out-
of-position. The agency believes it is essential to ensure seat belt 
assemblies perform their important safety function of not exceeding the 
permitted maximum webbing pay-out/elongation, to protect occupants who 
may be out-of-position during a crash, and the resulting increased risk 
of that occupant striking the vehicle's interior structure.
b. The Absence of Complaints Does Not Support GM's Petition
    GM stated that they received no complaints and knew of no reported 
injuries related to the noncompliance when they filed this petition in 
September of 2017. NHTSA does not consider the absence of complaints or 
injuries to show that the issue is inconsequential to safety; the 
absence of a complaint does not mean there have been no safety issues, 
nor that there will not be any in the future. In any event, three 
injuries involving 2500 series vehicles' seat belt assemblies were 
reported in the Early Warning Reporting database in the second quarter 
of 2018.
c. That GM Has Corrected the Noncompliance for Vehicles Produced After 
August 7, 2017, Does Not Support the Merits of Its Petition
    Manufacturers are legally obligated to correct new vehicle 
production. See 49 U.S.C. 30112(a); 30115(a). A manufacturer cannot 
certify or manufacture for sale a vehicle it knows to be noncompliant. 
Id. The fact that new vehicle production has been corrected simply 
informs the agency that the noncompliance is limited to the affected 
vehicles described in the petition. Therefore, the fact that new 
vehicle production has been corrected does not factor into our analysis 
of whether the noncompliance is inconsequential and will not justify 
our granting an inconsequentiality petition.

VII. NHTSA's Decision

    In consideration of the foregoing, NHTSA finds that GM has not met 
its burden of persuasion that the subject FMVSS No. 209 noncompliance 
in the subject vehicles is inconsequential to motor vehicle safety. 
Accordingly, NHTSA hereby denies GM's petition. GM is therefore 
obligated to provide notification of, and a free remedy for, that 
noncompliance in accordance with 49 U.S.C. 30118 through 30120.

(Authority: 49 U.S.C. 30118, 30120: delegations of authority at 49 
CFR 1.95 and 501.8)

Jeffrey Mark Giuseppe,
Associate Administrator for Enforcement.
[FR Doc. 2020-24866 Filed 11-9-20; 8:45 am]
BILLING CODE 4910-59-P


