
[Federal Register Volume 81, Number 228 (Monday, November 28, 2016)]
[Proposed Rules]
[Pages 85478-85488]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-28125]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

National Highway Traffic Safety Administration

49 CFR Part 575

[NHTSA-2015-0096]
RIN 2127-AL33


Vehicle Defect Reporting Requirements

AGENCY: National Highway Traffic Safety Administration (NHTSA), 
Department of Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: NHTSA is proposing to require placing a label on the passenger 
side sun visor of light-duty vehicles that provides information about 
how to submit a safety-related motor vehicle defect complaint to NHTSA. 
This rulemaking also proposes updating the required information in 49 
CFR 575.6 for defect reporting information in owner's manuals through 
the addition of the text developed for this proposal. This proposal 
responds to the mandate in the Moving Ahead for Progress in the 21st 
Century Act of 2012 (MAP-21) that manufacturers be required to affix, 
in the glove compartment or in another readily accessible location on 
the vehicle, a sticker, decal, or other device that provides, in simple 
and understandable language, information about how to submit a safety-
related motor vehicle defect complaint to NHTSA; and prominently print 
the information described above within the owner's manual.

DATES: Comments must be received on or before January 27, 2017. See the 
SUPPLEMENTARY INFORMATION section on ``Public Participation'' for more 
information about written comments.

ADDRESSES: You may submit your comments, identified by Docket ID No. 
NHTSA-2015-0096, by any of the following methods:
     http://www.regulations.gov: Follow the online instructions 
for submitting comments.
     Fax: NHTSA: (202) 493-2251.
     Mail:
    [cir] Docket Management Facility, M-30, U.S. Department of 
Transportation, 1200 New Jersey Avenue SE., West Building, Ground 
Floor, Rm. W12-140, Washington, DC 20590, Attention Docket ID No. 
NHTSA-2015-0096.
     Hand Delivery:
    [cir] Department of Transportation, 1200 New Jersey Avenue SE., 
West Building, Ground Floor, Rm. W12-140, Washington, DC 20590, 
Attention

[[Page 85479]]

Docket ID No. NHTSA-2015-0096 between 9 a.m. and 5 p.m. Eastern Time, 
Monday through Friday, except federal holidays.
    Instructions: Regardless of how you submit comments, you should 
mention Docket ID No. NHTSA-2015-0096 or the Regulatory Identification 
Number (RIN) for this rulemaking. You may call the Docket Management 
Facility at 202-366-9826. For detailed instructions on submitting 
comments and additional information on the rulemaking process, see the 
Public Participation heading of the SUPPLEMENTARY INFORMATION section 
of this document. Note that all comments received will be posted, 
except as noted below, without change to http://www.regulations.gov, 
including any personal information provided.
    Docket: All documents in the dockets are listed in the http://www.regulations.gov index. Although listed in the index, some 
information is not publicly available, e.g., confidential business 
information (CBI) or other information whose disclosure is restricted 
by statute. Publicly available docket materials are available either 
electronically in http://www.regulations.gov or in hard copy at the 
Docket Management Facility, M-30, U.S. Department of Transportation, 
1200 New Jersey Avenue SE., West Building, Ground Floor, Rm. W12-140, 
Washington, DC 20590. The Docket Management Facility is open between 9 
a.m. and 5 p.m. Eastern Time, Monday through Friday, except federal 
holidays.
    Privacy Act: Anyone is able to search the electronic form of all 
comments received in any of our dockets by the name of the individual 
submitting the comment (or signing the comment, if submitted on behalf 
of an association, business, labor union, etc.). You may review DOT's 
complete Privacy Act Statement in the Federal Register published on 
April 11, 2000 (65 FR 19477-78) or you may visit http://www.dot.gov/privacy.html.

FOR FURTHER INFORMATION CONTACT: For technical issues: Hisham Mohamed, 
National Highway Traffic Safety Administration, 1200 New Jersey Avenue 
SE., Washington, DC 20590. Telephone: (202) 366-0307.
    For legal issues: Ryan Hagen, National Highway Traffic Safety 
Administration, 1200 New Jersey Avenue SE., Washington, DC 20590. 
Telephone: (202) 366-2992.

SUPPLEMENTARY INFORMATION:

Table of Contents

I. Executive Summary
II. Statutory Mandate
III. Background
IV. Alternatives Considered and Proposed for the Label
V. Alternatives Considered and Proposed for the Owner's Manual 
Information
VI. Costs
VII. Benefits
VIII. Enforcement and Compliance
IX. Proposed Compliance Date
X. Public Participation
XI. Regulatory Notices and Analyses
XII. Proposed Regulatory Text

I. Executive Summary

    This rulemaking proposes to require placing a sticker, decal, or 
other device that provides, in simple and understandable language, 
information about how to submit a safety-related motor vehicle defect 
complaint to NHTSA on the passenger side sun visor. The agency believes 
that the sun visor is not only the most accessible of the locations 
considered, but also it is the most prominent location, which would 
allow for the most informational benefit to consumers. This rulemaking 
also proposes updating the defect reporting information manufactures 
are required to include in owner's manuals. This rulemaking proposes to 
move the requirement to a different section of the CFR.
    The benefits of the proposed rule, although not quantifiable, are 
anticipated to include: (1) improved messaging and information to 
consumers on how to submit a safety-related motor vehicle defect 
complaint to NHTSA; (2) increased consumer involvement in the motor 
vehicle defect reporting process; (3) reduced time between consumer 
awareness of a possible motor vehicle defect and industry response; (4) 
cost savings to the consumer through improved and timely defect-related 
response by the manufacturer; (5) reduction in the risk and incidence 
of injuries and fatalities attendant with the possible safety-related 
motor vehicle defect; (6) decreased motor vehicle property damage; (7) 
improvement in agency data-collection on potential safety problems in 
motor vehicles and motor vehicle equipment, and resultant decisions on 
whether to open an investigation; and, (8) cost savings to the industry 
by providing motor vehicle manufacturers with information that they may 
not yet have identified and gathered. While NHTSA believes that the 
benefits of this proposed rule would outweigh the costs, NHTSA notes 
that this rulemaking is required by statute and the agency is not 
required to determine that it is cost-beneficial.

II. Statutory Mandate

    The Moving Ahead for Progress in the 21st Century Act of 2012 (MAP-
21) \1\ requires that NHTSA develop a rule to provide consumers with 
information, in simple and understandable language, on how to submit a 
safety-related motor vehicle defect complaint to NHTSA. This 
information is to be placed on a sticker, decal or other device affixed 
to each new vehicle and printed within the owner's manual.
---------------------------------------------------------------------------

    \1\ Public Law 112-141.
---------------------------------------------------------------------------

    Section 31306 of MAP-21 amended section 32302(d) of Chapter 323, 
Title 49, of the United States Code (U.S.C.). Chapter 323 codifies 
consumer information requirements initially established by the Motor 
Vehicle Information and Cost Savings Act of 1972 (Pub. L. 92-513). 
Section 31306 of MAP-21 requires that NHTSA develop a rulemaking to 
require passenger motor vehicle manufacturers (1) to affix, in the 
glove compartment or in another readily accessible location on the 
vehicle, a sticker, decal, or other device that provides, in simple and 
understandable language, information about how to submit a safety-
related motor vehicle defect complaint to NHTSA; and (2) to prominently 
print the information described above by placing the text in Bold 
letters within the owner's manual. Section 31306 specifies that the 
above information must not be placed on the label required under 
section 3 of the Automobile Information Disclosure Act (15 U.S.C. 
1232).
    The agency has interpreted Section 31306 as directing DOT (by 
delegation, NHTSA) to determine a readily accessible location in a 
passenger motor vehicle for the required information to be affixed 
(considering the glove compartment as one option), and to ensure that 
the information is conveyed in simple and understandable language via a 
sticker, decal, or other device. NHTSA believes that the determinations 
of whether to require (1) a particular location for the sticker, decal, 
or other device, (2) specified language to be used by all 
manufacturers, or (3) a particular location for the information in the 
owner's manual, are left to the agency's discretion. We have 
interpreted the terms ``sticker, decal, or other device,'' to be 
various forms of the term ``label.'' Thus, we use the term ``label'' 
throughout this proposal to refer to the various ways a manufacturer 
could place the required information on the vehicle. We believe this 
could be fulfilled either through an adhesive method, such as a label 
generally refers to, or through a printing method, where

[[Page 85480]]

text would be directly applied to a surface.
    This rulemaking satisfies this mandate by proposing to require 
manufacturers to place a label on the passenger side sun visor that 
provides concise information on how to submit a safety-related defect 
complaint to NHTSA. This rulemaking also proposes to require 
manufacturers to print the same information in the owner's manual.

III. Background

    Motor vehicle safety is defined as ``the performance of a motor 
vehicle or motor vehicle equipment in a way that protects the public 
against unreasonable risk of accidents occurring because of the design, 
construction, or performance of a motor vehicle, and against 
unreasonable risk of death or injury in an accident, and includes non-
operational safety of a motor vehicle.'' \2\ A defect includes ``any 
defect in performance, construction, a component, or material of a 
motor vehicle or motor vehicle equipment.'' \3\ Generally, a safety 
defect is defined as a problem that exists in a motor vehicle or item 
of motor vehicle equipment that poses an unreasonable risk to motor 
vehicle safety, and may exist in a group of vehicles of the same design 
or manufacture, or items of equipment of the same type and manufacture.
---------------------------------------------------------------------------

    \2\ 49 U.S.C. 30101(a)(8).
    \3\ 49 U.S.C. 30101(a)(2).
---------------------------------------------------------------------------

    The National Traffic and Motor Vehicle Safety Act of 1966 \4\ (the 
Vehicle Safety Act) granted NHTSA the authority to investigate defects 
and to determine whether a defect exists. If a safety defect is 
discovered, the manufacturer must notify NHTSA, as well as vehicle or 
equipment owners, dealers, and distributors. If NHTSA determines that a 
defect creates an unreasonable safety risk, the agency may require a 
manufacturer to notify consumers, remedy a defect or issue a 
recall.5 6 The manufacturer is then required to remedy the 
problem at no charge to the owner. NHTSA monitors the manufacturer's 
corrective action to ensure successful completion of the recall 
campaign. Since the passage of the Vehicle Safety Act,\7\ 605 million 
cars, trucks, buses, recreational vehicles, motorcycles, and mopeds, as 
well as nearly 59 million tires, 91 million items of motor vehicle 
equipment, and 60 million child safety seats have been recalled to 
correct safety defects.\8\
---------------------------------------------------------------------------

    \4\ Codified at 15 U.S.C. 1381 et seq. and recodified in 1994 as 
Chapter 30, Title 49, of the United States Code.
    \5\ A manufacturer of a motor vehicle or motor vehicle equipment 
is required by 49 U.S.C. 30118(c) to notify the Secretary by 
certified mail, and the owners, purchasers, and dealers of the 
vehicle or equipment as provided in section 30119(d) of this 
section, if the manufacturer--
    (1) learns the vehicle or equipment contains a defect and 
decides in good faith that the defect is related to motor vehicle 
safety; or
    (2) decides in good faith that the vehicle or equipment does not 
comply with an applicable motor vehicle safety standard prescribed 
under this chapter.
    Section 30119(d) provides notification procedures. Section 
30120(a) of 49 U.S.C. provides that when notification is required 
under section 30118(c), the remedy shall be without charge when the 
vehicle or equipment is presented for remedy. NHTSA regulations at 
49 CFR part 573 ``Defects and noncompliance responsibility and 
reports,'' and Part 577 ``Defects and noncompliance notification'' 
implement these statutory requirements.
    Pursuant to 49 U.S.C. 30165, a manufacturer who violates any of 
the above-mentioned statutory or regulatory provisions is liable to 
the Government for a civil penalty. Until 1997 the maximum civil 
penalty was $1,000 per violation up to a maximum of $800,000 for a 
related series of violations. By a separate statutorily mandated 
regulation, since 1997 NHTSA has adjusted the Sec.  30165 civil 
penalties upward for inflation. 49 CFR part 578. The Transportation 
Recall Enhancement, Accountability, and Documentation (TREAD) Act, 
(Pub. L. 106-414), enacted in 2000 in light of the Firestone/Ford 
controversy, amended the Safety Act by, inter alia, raising those 
maximum civil penalties to $5,000 per violation and $15,000,000 for 
a related series of violations, and added criminal penalties (49 
U.S.C. 30170) for violations of reporting requirements. MAP-21, 
enacted in 2012, increased the maximum civil penalty for a related 
series of violations to $35,000,000. The Fixing America's Surface 
Transportation Act (FAST Act), Public Law 114-94 (Dec. 4, 2015), 
increased maximum civil penalties to $21,000 per violation and 
$105,000,000 for a related series of violations. The increases in 
maximum civil penalties in the FAST Act become effective on the date 
on which the Secretary of Transportation certifies that NHTSA has 
completed a rulemaking to provide an interpretation of the penalty 
factors in 49 U.S.C. 30165. The higher civil penalty maximums in the 
Part 578, MAP-21, and the FAST Act amendments are not retroactive to 
violations that occurred before their enactments.
    \6\ Under the 1974 amendments to the Motor Vehicle Safety Act, 
Congress gave NHTSA broad new power to enforce recall decisions. 
These included new reporting requirements, increased penalties for 
noncompliance, and subpoena and plant inspection authority.
    \7\ During the period 1966 to 2014.
    \8\ 2014 Recall Annual Report--NHTSA. See report at http://www.safercar.gov/staticfiles/safercar/pdf/2014-annual-recalls-report.pdf (last accessed September 18, 2015). This data includes 
recalls that take place because the vehicles and equipment do not 
meet the requirements of applicable safety standards set by NHTSA. 
Manufacturers voluntarily initiate most recalls.
---------------------------------------------------------------------------

    To obtain information about potential safety defects in vehicles 
and equipment, NHTSA's Office of Defects Investigation (ODI) receives 
data from a variety of sources including vehicle and equipment 
manufacturers, dealers, and consumer advocacy groups and forums. 
However, ODI relies heavily on information received from consumers who 
experience issues with their vehicles and equipment. ODI receives, on 
average, between 40,000 and 50,000 complaints from consumers each year.
    If a consumer thinks that his/her vehicle or equipment may have a 
safety-related defect, reporting it to NHTSA is an important first step 
to take to get the situation remedied and help make the nation's roads 
safer. If the agency receives similar reports from a number of 
consumers about the same product, this could indicate that a safety-
related defect exists that could warrant the opening of an 
investigation. However, an analysis of one complaint may also lead to 
an investigation depending on the type of defect that is reported. In 
order to make it convenient for consumers to report any suspected 
safety-related defects to NHTSA, the agency offers three ways to file 
such complaints.

Vehicle Safety Hotline

    NHTSA operates the United States Department of Transportation's 
Vehicle Safety Hotline telephone service to collect accurate and timely 
information from consumers on vehicle safety problems. Consumers can 
call 1-888-327-4236 or 1-800-424-9393 toll-free from anywhere in the 
United States, Puerto Rico, and the Virgin Islands to register 
complaints or receive recall information about a vehicle. The Hotline 
also has Spanish-speaking representatives and offers a dedicated 
number, 1-800-424-9153, for use by persons with hearing impairments.
    When a consumer calls the Hotline to report a vehicle-related 
safety issue, the consumer is asked to provide certain critical 
information that NHTSA technical staff needs to evaluate the 
problem.\9\ The information that the consumer provides is filed on a 
Vehicle Owner's Questionnaire (VOQ) form, entered into the agency's 
consumer-complaint database, and forwarded to NHTSA technical staff for 
evaluation. VOQs filed through the Hotline are mailed to consumers for 
verification of data. In addition, consumers receive an explanation of 
how their questionnaire will be used. NHTSA may provide information 
from the questionnaire to the vehicle manufacturer.
---------------------------------------------------------------------------

    \9\ The Privacy Act of 1974--Public Law 93-579, As Amended: This 
information is requested pursuant to the authority vested in the 
National Highway Traffic Safety Act and subsequent amendments. 
Consumers are under no obligation to respond to this questionnaire. 
Consumer response may be used to assist NHTSA in determining whether 
a manufacturer should take appropriate action to correct a safety 
defect. If NHTSA proceeds with administration enforcement or 
litigation against a manufacturer, consumer response, or statistical 
summary thereof, may be used in support of the agency's action.

---------------------------------------------------------------------------

[[Page 85481]]

Safercar.gov

    Consumers can also report a vehicle safety issue to NHTSA online at 
its vehicle safety Web site: www.safercar.gov. The consumer can select 
``Report Safety Problems'' within the Vehicle Owners section of the 
home page. The information that a consumer submits via the Web site is 
recorded in VOQ format, entered into NHTSA's consumer complaint 
database, and provided to NHTSA technical staff for evaluation. NHTSA 
may provide information from the questionnaire to the vehicle 
manufacturer.

U.S. Mail

    A consumer can also report a defect by sending a letter to the 
agency via U.S. mail.

SaferCar Mobile Application

    In March 2013, NHTSA launched its SaferCar mobile application that 
allows consumers to access important vehicle safety information from 
their mobile devices.\10\ To report a safety complaint to NHTSA through 
the SaferCar mobile application, a consumer who has a smart phone or a 
tablet can download the SaferCar application for free, scan in their 
vehicle identification number, and follow instructions to submit their 
complaint. The information collected through this mobile application is 
similar to that which is collected online at SaferCar.gov.
---------------------------------------------------------------------------

    \10\ The current SaferCar mobile application is available for 
the iOS and Android mobile operating systems.
---------------------------------------------------------------------------

    Manufacturers are currently required to include the following text 
in all passenger vehicle owner's manuals: \11\
---------------------------------------------------------------------------

    \11\ 49 CFR 575.6.

    If you believe that your vehicle has a defect which could cause 
a crash or could cause injury or death, you should immediately 
inform the National Highway Traffic Safety Administration (NHTSA) in 
addition to notifying [INSERT NAME OF MANUFACTURER].
    If NHTSA receives similar complaints, it may open an 
investigation, and if it finds that a safety defect exists in a 
group of vehicles, it may order a recall and remedy campaign. 
However, NHTSA cannot become involved in individual problems between 
you, your dealer, or [INSERT NAME OF MANUFACTURER].
    To contact NHTSA, you may call the Vehicle Safety Hotline toll-
free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh 
Street, SW., Washington, DC 20590. You can also obtain other 
information about motor vehicle safety from http://www.safercar.gov.

    NHTSA notes that this required text uses an outdated mailing 
address. The correct mailing address is: U.S. Department of 
Transportation, National Highway Traffic Safety Administration, Office 
of Defects Investigation (NEF-100), 1200 New Jersey Avenue SE., 
Washington, DC 20590.
    The currently required text also does not advise vehicle users of 
the ability to file a complaint on the safercar.org Web site, or 
through the new safercar.gov mobile application.

IV. Alternatives Considered and Proposed for the Label

    NHTSA first considered whether to require a particular location for 
the label containing defect reporting language, or whether to leave the 
location up to the manufacturer's discretion. Section 31306 does not 
specify whether the determination of location is to be made by the 
agency or the manufacturer. NHTSA acknowledges that differing vehicles 
designs may mean that the most accessible location for a label in a 
particular vehicle also differs. We also considered that there may be 
benefits to providing flexibility to manufacturers by allowing them to 
make the location determination. The agency believes that increased 
compliance flexibility often has the potential to lower costs while 
preserving manufacturer ability to design to consumer preferences. In 
this case, however, the benefits to increased manufacturer flexibility 
are believed to be minimal. The base estimated costs of implementing 
this proposal are believed to be low, and the agency does not believe 
that additional flexibility would be able to provide any significant 
further cost savings. In addition, the purpose of requiring such a 
label is to ensure that consumers encounter the information; to the 
extent that a manufacturer seeks to ``blend'' the label into 
preexisting vehicle designs, we believe this may detract from the 
purpose of the requirement.
    On the other hand, we believe a standardized location for defect 
reporting information would best further the purpose of Section 31306 
by increasing the accessibility of the information through repeat 
consumer exposure and expectations. We anticipate that once the 
consumer has encountered the information in a particular vehicle 
location, he or she would be more likely to associate the information 
with the location and be able to access it again at a point when it is 
sought (such as after a safety incident has occurred or a defect 
suspected). Therefore, we are proposing to require a particular 
location for placement of the language by all manufacturers.
    NHTSA identified five locations on a vehicle where the placement of 
a label is likely to be practicable and the information displayed 
likely to be accessible to a consumer. The five options thus considered 
in this proposal are: (1) the passenger's sun visor; (2) the glove 
compartment; (3) the edge of the driver's door; (4) the driver's side 
B-pillar, and (5) the headliner above the sun visor. Section 31306 of 
MAP-21 (``. . . affix, in the glove compartment or in another readily 
accessible location on the vehicle . . .'') appears to suggest that the 
glove compartment may be the best location for the label, however, the 
selection of the location is left to the agency's discretion.
    Merriam-Webster dictionary defines ``accessible'' as ``capable of 
being reached, easy to communicate, capable of being influenced, 
capable of being used or seen, or capable of being understood or 
appreciated.'' \12\ NHTSA notes that while Section 31306 does not 
mandate that the required location be determined to be the most 
accessible of all the options, Congress appears to have given the 
accessibility of the information the highest priority of potential 
factors. The agency notes that in the context of placing displays of 
information, the prominence of the placement directly influences the 
degree to which the information can be seen, and thus the degree to 
which the language can communicate and be understood. Prominence is 
thus an important element of accessibility when considering where to 
put a label. Therefore, NHTSA first focused its analysis on which 
prominent locations inside the vehicle could display information that 
would then be highly accessible to (i.e., reachable by) vehicle users.
---------------------------------------------------------------------------

    \12\ Merriam-Webster Online--http://www.merriam-webster.com/dictionary/accessible (last accessed January 23, 2013).
---------------------------------------------------------------------------

    First, NHTSA considered the glove compartment for prominence and 
accessibility, as this location was specifically suggested by Congress. 
We believe this location may have been suggested because of the common 
practice of storing documents such as the vehicle owner's manual, 
registration, and insurance information, which a driver is likely to 
reference in the event of an accident or problem with the vehicle. In 
addition, glove compartments face the vehicle occupants and are 
generally within a few feet of eye level, which may make information 
displayed within one more prominent than it would be in locations that 
are behind or to side of occupants, or further from eye level.
    However, the agency believes that the variety in current designs of 
glove

[[Page 85482]]

compartments may impact the degree of accessibility and prominence of 
information displayed within them. For example, we are aware of some 
designs that open on a simple hinge, similar to an envelope drop box, 
and others that open on a hinge that drops the compartment down below 
the dashboard. After consideration of the surface areas available for 
placement of a label within different glove compartment designs, we are 
concerned the variation in designs may make placement of a label inside 
the glove compartment more visible on some vehicles than others. Not 
all glove compartments appear to offer a prominent surface area on 
which to place a label with detailed reporting information. 
Additionally, we believe that consistency in visibility of the label 
across model types may make it more accessible and prominent to 
consumers through their past associations with labels in other 
vehicles.
    Next, NHTSA considered the passenger's side sun visor. This 
location was considered accessible and prominent, as it is situated in 
front of vehicle occupants not far from eye level. The suitability of 
this location for labels has previously been leveraged by the agency 
for both air bag labels and vehicle rollover labels.
    The air bag label, established under FMVSS 208 (Occupant Crash 
Protection), requires manufacturers to affix an air bag warning label 
to the sun visor at each seating position that is equipped with an 
inflatable restraint.\13\ 49 CFR part 575.105 (Vehicle Rollover) also 
requires that a rollover warning label be affixed at the driver's sun 
visor for utility vehicles.\14\ The rollover warning label may appear 
on either side of the visor, but if it appears on the same side as the 
air bag label, it must be separated from the air bag label by a certain 
distance. The air bag label may be affixed to either side of the sun 
visor. FMVSS 208 also specifies that no other information may appear on 
the same side of the sun visor to which the air bag warning label is 
affixed, except for the utility vehicle warning label, and no other 
information about the air bags or the need to wear seat belts may 
appear anywhere on sun visors.\15\
---------------------------------------------------------------------------

    \13\ Sec.  571.208, Standard No. 208; Occupant crash protection.
    S4.5.1(b) Sun visor air bag warning label. (1) Except as 
provided in S4.5.1(b)(2), each vehicle shall have a label 
permanently affixed to either side of the sun visor, at the 
manufacturer's option, at each front outboard seating position that 
is equipped with an inflatable restraint.
    \14\ Sec.  575.105 Vehicle rollover.
    c) Definitions. Utility vehicles means multipurpose passenger 
vehicles (other than those which are passenger car derivatives) 
which have a wheelbase of 110 inches or less and special features 
for occasional off-road operation.
    \15\ Sec.  571.208.
    S4.5.1(b)(5) Limitations on additional labels. (i) Except for 
the information on an air bag maintenance label placed on the sun 
visor pursuant to S4.5.1(a) of this standard, or on a utility 
vehicle warning label placed on the sun visor that conforms in 
content, form, and sequence to the label shown in Figure 1 of 49 CFR 
575.105, no other information shall appear on the same side of the 
sun visor to which the sun visor air bag warning label is affixed.
    (ii) Except for the information in an air bag alert label placed 
on the sun visor pursuant to S4.5.1(c) of this standard, or on a 
utility vehicle warning label placed on the sun visor that conforms 
in content, form, and sequence to the label shown in Figure 1 of 49 
CFR 575.105, no other information about air bags or the need to wear 
seat belts shall appear anywhere on the sun visor.
---------------------------------------------------------------------------

    NHTSA considered that the label for information on how to contact 
NHTSA with a vehicle safety defect complaint could be affixed on the 
passenger's sun visor on the opposite side from the air bag warning 
label, which would allow for sufficient separation of the two labels. 
As each label would contain concise information, we believe that such 
separation from the pictogram of the air bag label would be sufficient 
to ensure that both labels display information prominently. We note 
that a similar setup exists on the driver side sun visor of utility 
vehicles, which bears either the air bag label on one side and the 
rollover warning label on the other side of the visor, or both labels 
on the same side. The agency is not aware of any negative impacts from 
the placement of two labels on one visor on those vehicles.
    NHTSA next considered the driver's side b-pillar or edge of the 
driver's door. In its tire safety information final rule,\16\ the 
agency agreed with manufacturers that there is a concern about the 
sufficiency of the space for the placement of the vehicle placard and 
tire inflation label in the door edge or B-pillar for some vehicles. As 
a result, in that rule, NHTSA added other alternative requirements to 
the requirement that the vehicle placard and tire inflation pressure 
label be located on the driver's side B-pillar.\17\ The agency remains 
concerned that the relatively limited space in these locations, 
combined with design variations, may detract from the prominence of a 
label with detailed reporting information. We also believe that the 
current vehicle placard and tire inflation pressure label are 
relatively technically specific, and by adding another label may crowd 
the messaging on how to reach NHTSA with a potential vehicle safety 
complaint.
---------------------------------------------------------------------------

    \16\ 67 FR 69600, at 69617-69618.
    \17\ Id. at 69617.
---------------------------------------------------------------------------

    Finally, NHTSA considered the headliner above the sun visor. Like 
the sun visor, the headliner is a relatively accessible and prominent 
location, being in front of the vehicle occupants and not far from eye 
level. A label on either the headliner or the ``back'' side of the 
visor would only be visible when the visor was in the ``open'' (not 
stowed) position. As the headliner currently does not contain labels, a 
potential benefit to using this space for the defect label would be to 
avoid any confusion or crowding of information.\18\ The ability to 
require the label on the driver's side headliner, as opposed to the 
passenger's side sun visor may carry additional accessibility benefits 
by bringing the information closer to the driver, who is more likely to 
need or use the information.
---------------------------------------------------------------------------

    \18\ Related, the headliner may provide for more consistency in 
label placement if manufacturers frequently vary whether to place 
the air bag label on the front or back side of the label. However, 
NHTSA believes that the variation in air bag label placement is 
likely due to manufacturer desire to limit the label visibility to 
when the visor is in the open position, and requiring a label on 
each side of the visor would make that concern irrelevant.
---------------------------------------------------------------------------

    However, a label on the back side of the visor would appear closer 
to eye level when the visor was in the open position. NHTSA is also 
concerned that the potential use of the driver's side headliner may 
introduce a crowding issue in utility vehicles, which would now have 
three informational labels in the same area on the driver's side (this 
could defeat any spacing benefit assumed for avoiding the use of the 
sun visor). In addition, the use of the visor for existing label 
requirements may make it more likely that a vehicle occupant would 
associate the visor with vehicle safety-related reference information 
and thus check it in the event of a safety problem. For these reasons, 
the agency believes a label on the headliner may be less prominent than 
one on the visor itself.
    For the above reasons, of the five locations considered, the 
agency's preferred alternative for placement of the sticker, decal, or 
other device is the passenger side sun visor. The agency also 
recognizes that the headliner above the sun visor may have similar 
benefits to the visor without some of the disadvantages of the visor. 
Therefore, the headliner is currently considered a close second to the 
preferred alternative.
    NHTSA invites comments on whether the passenger side sun visor is 
indeed the best easily accessible location for a label, as well as 
whether the agency should have considered additional locations within 
the vehicle. Commenters should provide detail on

[[Page 85483]]

which location is best and why. If additional locations are suggested, 
commenters are requested to provide information on the accessibility, 
prominence, and practicability of the suggested location. NHTSA also 
invites comments on whether its assumptions and assessment of the 
preferred location are reasonable. Commenters are requested to provide 
supporting information for their suggestions.
Specified Language
    NHTSA also considered whether to require specified language to be 
printed on the label, or whether to leave the choice of language up to 
the vehicle manufacturer. Section 31306 of MAP-21 does not specify 
whether the choice of actual content is to be made by the agency or by 
the manufacturer. Given that information on how to submit a safety-
related defect complaint is relatively straightforward, and does not 
vary by vehicle type or design, we do not see a benefit to leaving the 
choice of language up to the manufacturer. Conversely, we believe that 
requiring standardized language could prevent confusion or inaccuracies 
that customized language could produce. Further, standardized language 
may have the benefit of creating a phrase association for vehicle users 
that could help them remember which agency to contact with a safety-
related concern whether or not they remember where the contact 
information is located within their vehicle. For these reasons, NHTSA 
is proposing standardized language for the decal, label, or other 
device.
    Next, NHTSA considered proposed content for the labels. Information 
on how to reach NHTSA with potential vehicle safety defect complaints 
is currently written in all passenger vehicle owner's manuals. 
Manufacturers are currently required to include the following text in 
all passenger vehicle owner's manuals: \19\
---------------------------------------------------------------------------

    \19\ 49 CFR 575.6.

    If you believe that your vehicle has a defect which could cause 
a crash or could cause injury or death, you should immediately 
inform the National Highway Traffic Safety Administration (NHTSA) in 
addition to notifying [INSERT NAME OF MANUFACTURER].
    If NHTSA receives similar complaints, it may open an 
investigation, and if it finds that a safety defect exists in a 
group of vehicles, it may order a recall and remedy campaign. 
However, NHTSA cannot become involved in individual problems between 
you, your dealer, or [INSERT NAME OF MANUFACTURER].
    To contact NHTSA, you may call the Vehicle Safety Hotline toll-
free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh 
Street SW., Washington, DC 20590. You can also obtain other 
information about motor vehicle safety from http://www.safercar.gov.

    Section 31306 of MAP-21 states that the label information must be 
``in simple and understandable language.'' Given the currently required 
language, NHTSA interprets one purpose of the new requirement as 
relaying the same basic information to vehicle users in a more 
straightforward and condensed manner appropriate for a sticker or 
label. With that in mind, NHTSA developed the following proposed 
language for the consumer information label:

Do you believe your vehicle has a safety-related problem?

    The National Highway Traffic Safety Administration (NHTSA) NEEDS to 
know.
    File your complaint with NHTSA today! Filing a complaint is easy:

Online: http://www.safercar.gov
Toll-free Hotline: 1-888-327-4236 (TTY: 1-800-424-9153)
Mail: U.S. Department of Transportation, NHTSA, Office of Defects 
Investigation, NEF-100, 1200 New Jersey Avenue SE., Washington, DC 
20077-9382.

    Information about how to keep your vehicle safe can be found at 
www.SaferCar.gov.

    NHTSA believes the above proposed language would be easily readable 
and comprehensible, and that by sticking to brief, standardized 
content, the proposed device would effectively inform consumers of how 
to file a potential vehicle safety defect. The agency believes that 
longer strings of information in this context are unnecessary, and may 
detract from a vehicle user's ability to internalize the information 
presented. The simple listing format above is intended to make it less 
likely that a vehicle user would miss the key message of the label or 
device.
    NHTSA requests comment on the language, including whether it 
provides the necessary information on how to contact NHTSA with vehicle 
safety-related complaints, and whether it is simple and understandable. 
Should the commenter have additional or revised language to propose, 
the agency requests detail as to what additional or revised language is 
recommended and how it is likely to fulfill the statutory purpose 
better than the proposed text.
Label Design
    NHTSA believes the intent of Section 31306 of MAP-21 was to provide 
consumers with easily accessible and understandable information on how 
to contact the agency with any vehicle safety-related defects and 
complaints. NHTSA does not believe that the requirements under this 
rule are intended to increase a manufacturer burden beyond 
communicating the basic information on how to contact the agency with a 
vehicle safety-related defect complaint.
    With that in mind, NHTSA is proposing the following simple design 
requirements for the label, which are similar to the design 
requirements of the air bag warning label and the rollover warning 
label: \20\
---------------------------------------------------------------------------

    \20\ See 49 CFR part 571.208; 49 CFR part 575.105, Vehicle 
Rollover.
---------------------------------------------------------------------------

     The title must be in a bold black text.
     The message area must be white with black text.
     The pictograms must be black with a white background.
     The label must be appropriately sized so that it is 
legible, visible and prominent to the driver.
    NHTSA believes that these requirements communicate the information 
as intended in the statute in an accessible, readable, and 
comprehensive manner. NHTSA believes that a simple black and white 
label would effectively communicate the necessary information, and that 
requiring color on labels could create an unnecessary financial burden 
to some manufacturers. In regard to the font for the label, NHTSA is 
not proposing either a particular font face, font size, or case for the 
label. In existing label requirements (e.g., tire, rollover, and air 
bag), the agency has not encountered issues with leaving the font 
specifications up to manufacturers. However, NHTSA is proposing to 
specify that the text on the label be ``legible, visible, and 
prominent'' to the driver.\21\ NHTSA is also not proposing to specify a 
size, shape, or dimension for the label, in order to provide 
manufacturers the flexibility to design the placard and label in a 
manner that can be configured to each vehicle design. This flexibility 
is similar to that provided in other label requirements.\22\ A sample 
of the proposed label is as follows:
---------------------------------------------------------------------------

    \21\ See 67 FR 69617.
    \22\ Id.

---------------------------------------------------------------------------

[[Page 85484]]

[GRAPHIC] [TIFF OMITTED] TP28NO16.007

    NHTSA seeks comments on the proposed design of the label, including 
the current recommendation to keep the label in black and white without 
additional colors. If a comment requests that the labels have color, 
either on the background and/or in the content including text, the 
commenter should provide a detailed explanation as to the benefit such 
changes would provide to the consumer. NHTSA also seeks comment on the 
proposed content, as to whether the information is adequate to inform 
consumers on what actions to take should they feel they have a safety-
related problem with their vehicle, and whether there is any undue 
burden that vehicle manufacturers may face under this proposal that the 
agency should consider.

V. Alternatives Considered and Proposal for the Owner's Manual 
Information

    NHTSA considered whether to develop unique language for owner's 
manuals on how to submit a defect complaint, whether to use the same 
language in the manual as is required for the label, or whether to 
simply update the currently required owner's manual information with 
NHTSA's new address and SaferCar mobile application.
    NHTSA believes that the clearest way to read Section 31306(d)(1)(B) 
of MAP-21 (``prominently print the information described in [the label 
requirement] within the owner's manual'') is that Congress intended for 
the same essential information displayed in the label to be available 
in the owner's manual, but not necessarily that the label be exactly 
reproduced in the owner's manual. If Congress had intended for the 
label to be printed in both places, we believe it would have indicated 
so more directly by combining the two requirements, rather than refer 
to the required information more broadly as that ``described in'' the 
label requirement. Further, we believe that the greater space offered 
in owner's manuals allows for additional explanatory statements that 
may be useful to a consumer seeking more information on the defects 
reporting process.
    For the above reasons, NHTSA is proposing the following language 
for the owner's manual requirement:

    If you believe that your vehicle has a defect which could cause 
a crash or could cause injury or death, you should immediately 
inform the National Highway Traffic Safety Administration (NHTSA) in 
addition to notifying [INSERT NAME OF MANUFACTURER].
    If NHTSA receives similar complaints, it may open an 
investigation, and if it finds that a safety defect exists in a 
group of vehicles, it may order a recall and remedy campaign. 
However, NHTSA cannot become involved in individual problems between 
you, your dealer, or [INSERT NAME OF MANUFACTURER].
    To contact NHTSA, you may call the Vehicle Safety Hotline toll-
free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; download the SaferCar mobile application; or write 
to: Administrator, NHTSA, 1200 New Jersey Ave. SE., Washington, DC 
20590. You can also obtain other information about motor vehicle 
safety from http://www.safercar.gov.

    NHTSA is not proposing design requirements for the owner's manual 
information, beyond that it must be printed in a font size no smaller 
than 10 point type. NHTSA is also not proposing to require the owner's 
manual information to be printed in a particular section of the manual. 
We recognize that there may be some increased consumer exposure benefit 
to requiring the information to be printed in a standard design, and/or 
on a particular page of the manual. However, in the event of a safety-
related issue with their vehicle, we believe it is common for a vehicle 
user to consult the table of contents within the manual for direction 
on their particular issue, and thus would be informed of where to find 
the information on how to submit a defect complaint. We also believe 
that manufacturers would be capable of fulfilling the statutory 
requirement to print the information prominently without the potential 
burden of redesigning their manual layouts to incorporate a 
standardized placement.
    NHTSA is also proposing to move the required language currently 
located in 49 CFR part 575.6 to 49 CFR 575.501 in order keep these like 
requirements in the same place. This section will provide manufacturers 
with the required safety-related defect reporting information in the 
owner's manual. As noted above, the current requirement does not 
include the most up-to-date reporting information, including the 
Safercar mobile application, and we believe that Congress developed the 
new owner's manual requirement with the intent that it would subsume 
the existing regulation.
    NHTSA requests comment on the proposal to use an updated version of 
the currently required owner's manual information, including whether 
this

[[Page 85485]]

would fulfill the statutory requirement. NHTSA also requests comment on 
whether to require specific design requirements and whether to require 
the owner's manual information in a particular section of the manual, 
and whether our assessment of the limited benefits of such additional 
requirements is accurate. Commenters are requested to provide detailed 
explanations for any recommendations.

VI. Costs

    In determining estimated industry costs associated with this 
proposal, the agency investigated potential ``ball-park'' production 
cost and labor cost for labels and owner's manual information.
    For purposes of the label cost estimate, NHTSA estimates the one-
time cost and recurring annual cost associated with producing a new, 
adhesive-type label that is separate from existing labels. NHTSA 
estimates that the one-time cost per manufacturer for development of 
the label is $22.67, assuming one hour of labor. The labor cost 
estimate is based on the Bureau of Labor Statistics Motor Vehicle 
Manufacturing average hourly wage of production workers.\23\ See Table 
1. The total one-time industry cost to 22 manufacturers of passenger 
cars and light trucks is estimated at $586.74.
---------------------------------------------------------------------------

    \23\ http://www.bls.gov/oes/current/oes519199.htm.

                             Table 1--Estimated One-Time Manufacturer Cost for Label
                                                 [2012 Dollars]
----------------------------------------------------------------------------------------------------------------
                                                               Estimated labor  Estimated labor      Cost per
                    One-time startup costs                         rate/hour          hours        manufacturer
----------------------------------------------------------------------------------------------------------------
Motor Vehicle Manufacturing Production Worker................          $26.67                1           $26.67
----------------------------------------------------------------------------------------------------------------

    We estimate the annual costs for producing the label as follows. 
NHTSA assumes a per-label cost of $0.04 and a labor value of $0.09 per 
label. To arrive at a labor value of $0.09, we estimate the average 
assembly line worker salary \24\ ($21.14) divided by 60 minutes, 
divided by 60 seconds = $0.0059 per second. We estimate that affixing 
the label on the sun visor would take approximately 15 seconds, based 
on the amount of time we assumed the average worker would take to open 
the vehicle door, position the sun visor, and affix the label. This 
also assumes that, like the VIN numbers, the label would be affixed to 
the vehicle after it is assembled. We assume that 16.5 million 
passenger vehicles will be sold per year.\25\ Based on the above, we 
estimate that the total annual industry cost for the label, including 
printing and labor, is $2.15 million. See Table 2.
---------------------------------------------------------------------------

    \24\ http://www.bls.gov/oes/current/oes512099.htm.
    \25\ See 78 FR 55138.

                               Table 2--Estimated Total Label Annual Industry Cost
                                                 [2012 Dollars]
----------------------------------------------------------------------------------------------------------------
                                                    Labor value     Cost w/out                       Industry
       Number of vehicles          Cost of label     per label         labor          $ Labor       annual cost
----------------------------------------------------------------------------------------------------------------
16.5 million....................           $0.04           $0.09        $660,000      $1,485,000  ..............
                                 -------------------------------------------------------------------------------
    Total cost..................  ..............  ..............  ..............  ..............      $2,145,000
----------------------------------------------------------------------------------------------------------------

    NHTSA developed the following cost estimates for the development 
and printing in simple and understandable language within the owner's 
manual, information about how to submit a safety-related motor vehicle 
defect complaint to the National Highway Traffic Safety Administration. 
See Table 3. The cost of printing the page the size of the required 
text is estimated at $0.04. Multiplying $0.04 by 16.5 million vehicles 
results in an estimated annual cost to vehicle manufacturers of 
$660,000 for printing the page in the owner's manual. The one-time cost 
to manufacturers for the information in the owner's manual is 
negligible.

                           Table 3--Estimated Owner's Manual Information Printing Cost
                                                 [2012 Dollars]
----------------------------------------------------------------------------------------------------------------
                          Annual costs                                 Rate            Pages           Cost
----------------------------------------------------------------------------------------------------------------
Printing--per page..............................................           $0.04               1           $0.04
16.5 million number of vehicles.................................  ..............  ..............         660,000
----------------------------------------------------------------------------------------------------------------

    The estimated total annual recurring cost to vehicle manufacturers 
is $2.8 million ($2.15 million label cost + $0.66 million owner's 
manual cost).

VII. Benefits

    As information on the effects of making defect reporting 
information more accessible to vehicle users is not available, the 
benefits of this proposed rule are not quantifiable. However, NHTSA 
believes that there would be several qualitative benefits of this 
action. Some of the anticipated benefits would fall to vehicle users. 
These benefits could be direct (improved consumer awareness and 
involvement) or indirect (fewer vehicle safety incidents or accidents 
across particular model types on account of an expanded or quickened 
defect reporting and response process). Other anticipated benefits 
would fall to agency and the industry in the form of efficiencies 
gained by closing information gaps. The anticipated benefits of this 
proposal include:

[[Page 85486]]

    (1) Improved messaging and information to consumers on how to 
submit a safety-related motor vehicle defect complaint to NHTSA;
    (2) increased consumer involvement in the motor vehicle defect 
reporting process;
    (3) reduced time between consumer awareness of a possible motor 
vehicle defect and industry response;
    (4) cost savings to the consumer through improved and timely 
defect-related response by the manufacturer;
    (5) reduction in the risk and incident of injuries and fatalities 
attendant with the possible safety-related motor vehicle defect;
    (6) decrease in motor vehicle property damage;
    (7) improvement in agency data-collection on potential safety 
problems in motor vehicles and motor vehicle equipment, and resultant 
decisions on whether to open an investigation; and,
    (8) cost savings to the industry by providing motor vehicle 
manufacturers with information that they may not yet have identified 
and gathered.
    The agency believes that the benefits of this proposal would be 
higher than the costs. NHTSA requests comment on the benefits described 
here, and on any additional benefits and/or ways to quantify benefits.

VIII. Compliance and Penalties

    In adding the 32302(d) requirements under MAP-21, Congress did not 
amend the existing compliance and civil penalty provisions in 49 U.S.C. 
Chapter 323; therefore, NHTSA tentatively concludes that those 
provisions apply for regulations promulgated under 32302(d).
    49 U.S.C. 32308(a) states, in relevant part, that a person commits 
a violation of Chapter 323 if that person fails to provide the 
Secretary of Transportation (by delegation, the Administrator of NHTSA) 
with information requested in carrying out Chapter 323, or fails to 
comply with the applicable regulations prescribed under Chapter 323. 
32308(b) prescribes a civil penalty of not more than $1,000 for each 
violation of 32308(a).

IX. Proposed Compliance Date

    The proposed compliance date for label and owner's manual 
requirements is the first model year that occurs more than one year 
following the publication date of a final rule implementing this 
proposal. The compliance date adheres to the provision in Section 
31306(d)(2) of MAP-21, which states that the above requirements ``shall 
apply to passenger motor vehicles manufactured in any model year 
beginning more than 1 year after the date on which a final rule is 
published.'' NHTSA believes the lead time proposed for the label may be 
necessary; however, early compliance would be encouraged. With regard 
to owner's manual information, NHTSA believes this amount of lead time 
is more than necessary. First, the agency is proposing standardized 
language. Additionally, in most cases, owner's manual information is 
developed, reviewed, and approved in an entirely digital environment, 
which significantly reduces lead time. Moreover, the agency is aware 
that some manufacturers have moved, or are in the process of moving, to 
full digital delivery of owner's manual information, where owner's 
manual information is delivered via a digital video disc (DVD) or some 
other digital format.\26\ In some of these cases, official vehicle 
manufacturer owner's manual information is available via the internet 
for reference; one manufacturer currently provides vehicle owners 
information via an electronic tablet device as the primary information 
source, with a more traditional paper version as a secondary 
method.\27\
---------------------------------------------------------------------------

    \26\ ``Chrysler Phases Out Paper Owner's Manual'' http://wheels.blogs.nytimes.com/2009/09/23/chrysler-does-away-with-paper-owners-manual/ (last accessed June 17, 2015).
    \27\ ``2012 Hyundai Equus Continues To Redefine Intelligent 
Luxury,'' http://www.hyundainews.com/us/en-us/Media/PressRelease.aspx?mediaid=32732&title=2012-hyundai-equus-continues-to-redefine-intelligent-luxury (last accessed February 5, 2016).
---------------------------------------------------------------------------

    NHTSA seeks comment on whether the proposed lead time is 
reasonable. If a commenter wishes the agency to provide additional lead 
time, NHTSA requests that the commenter provide specific explanations 
for why more lead time might be needed for which elements of the 
proposal. For example, if a commenter sought more lead time for the 
owner's manual requirements, NHTSA seeks any relevant details of the 
owner's manual publication process and associated timing, along with 
current and future media that would be used for the owner's manual 
information.

X. Public Participation

    NHTSA requests comment on all aspects of this proposed rule. This 
section describes how you can participate in this process.

A. How do I prepare and submit comments?

1. Further instructions for submitting comments to the NHTSA docket are 
described below:
    Your comments must be written and in English. To ensure that your 
comments are correctly filed in the docket, please include the Docket 
Number NHTSA-2015-0096 in your comments. Your comments must not be more 
than 15 pages long.\28\ NHTSA established this limit to encourage you 
to write your primary comments in a concise fashion. However, you may 
attach necessary additional documents, which are not subject to the 
page limit, to your comments.
---------------------------------------------------------------------------

    \28\ 49 CFR 553.21.
---------------------------------------------------------------------------

    If you are submitting comments electronically as a PDF (Adobe) 
file, we ask that the documents submitted be scanned using the Optical 
Character Recognition (OCR) process, thus allowing the agency to search 
and copy certain portions of your submissions.\29\ Please note that 
pursuant to the Data Quality Act, in order for the substantive data to 
be relied upon and used by the agencies, it must meet the information 
quality standards set forth in the OMB and DOT Data Quality Act 
guidelines.
---------------------------------------------------------------------------

    \29\ Optical character recognition (OCR) is the process of 
converting an image of text, such as a scanned paper document or 
electronic fax file, into computer-editable text.
---------------------------------------------------------------------------

    Accordingly, we encourage you to consult the guidelines in 
preparing your comments. OMB's guidelines may be accessed at http://www.whitehouse.gov/omb/fedreg_reproducible (last accessed January 2, 
2014), and DOT's guidelines may be accessed at http://regs.dot.gov 
(last accessed January 2, 2014).
2. Tips for Preparing Your Comments
    When submitting comments, please remember to:
     Identify the rulemaking by docket numbers and other 
identifying information (subject heading, Federal Register date and 
page number).
     Follow directions--the agencies may ask you to respond to 
specific questions or organize comments by referencing a Code of 
Federal Regulations (CFR) part or section number.
     Explain why you agree or disagree, suggest alternatives, 
and substitute language for your requested changes.
     Describe any assumptions and provide any technical 
information and/or data that you used.
     If you estimate potential costs or burdens, explain how 
you arrived at your estimate in sufficient detail to allow for it to be 
reproduced.
     Provide specific examples to illustrate your concerns and 
suggest alternatives.
     Explain your views as clearly as possible, avoiding the 
use of profanity or personal threats.
    Make sure to submit your comments by the comment period deadline 
identified in the DATES section above.

[[Page 85487]]

XI. Regulatory Notices and Analyses

A. Executive Orders 12866 and 13563

    NHTSA has considered the impact of this rulemaking action under 
Executive Orders 12866 and 13563 and the Department of Transportation's 
regulatory policies and procedures. This action is not significant and 
therefore was not subject to review by OMB under Executive Order 12866. 
The benefits and costs of this proposal are described above. Because 
the proposed rule would, if adopted, would not be economically 
significant, the agency has not prepared a separate Preliminary 
Regulatory Evaluation.

B. Regulatory Flexibility Act

    We estimate these proposed requirements would cost each small 
vehicle manufacturer approximately $0.13 per vehicle, or far less than 
1% of the cost of one of these vehicles, and would therefore not appear 
to constitute a significant economic impact. Thus, NHTSA certifies that 
this rule, if adopted, would not have a significant impact on a 
substantial number of small entities.

C. Executive Order 13132

    NHTSA does not believe that there would be sufficient federalism 
implications to warrant the preparation of a federalism assessment.

D. Executive Order 12988 (Civil Justice Reform)

    Pursuant to Executive Order 12988, ``Civil Justice Reform,'' \30\ 
NHTSA has considered whether this rulemaking would have any retroactive 
effect. This proposed rule does not have any retroactive effect.
---------------------------------------------------------------------------

    \30\ 61 FR 4729 (Feb. 7, 1996).
---------------------------------------------------------------------------

E. National Environmental Policy Act (NEPA)

    For the purposes of the National Environmental Policy Act, NHTSA 
has determined that implementation of this rulemaking action would not 
have any significant impact on the quality of the human environment.

F. Paperwork Reduction Act

    The proposed rule does not implicate any information collection 
requirements under the Paperwork Reduction Act of 1995 (44 U.S.C. 3501-
3520).

G. Unfunded Mandates Reform Act of 1995

    NHTSA has determined that the requirements of Title II of the 
Unfunded Mandates Reform Act of 1995 do not apply to this rulemaking.

H. National Technology Transfer Advancement Act

    Section 12(d) of the National Technology Transfer and Advancement 
Act (NTTAA) requires NHTSA to evaluate and use existing voluntary 
consensus standards in its regulatory activities unless doing so would 
be inconsistent with applicable law (e.g., the statutory provisions 
regarding NHTSA's vehicle safety authority) or otherwise impractical. 
NHTSA has not identified any existing voluntary consensus standards 
that could be used for this proposal.

I. Plain Language

    Executive Orders 12866 and 13563 require each agency to write all 
rules in plain language. Application of the principles of plain 
language includes consideration of the following questions:
     Have we organized the material to suit the public's needs?
     Are the requirements in the rule clearly stated?
     Does the rule contain technical language or jargon that is 
not clear?
     Would a different format (grouping and order of sections, 
use of headings, paragraphing) make the rule easier to understand?
     Would more (but shorter) sections be better?
     Could we improve clarity by adding tables, lists, or 
diagrams?
     What else could we do to make the rule easier to 
understand?

If you have any responses to these questions, please include them in 
your comments on this proposal.

J. Privacy Act

    Anyone is able to search the electronic form for all comments 
received into any of our dockets by the name of the individual 
submitting the comments (or signing the comment, if submitted on behalf 
of an association, business, labor union, etc.). For more information 
on DOT's implementation of the Privacy Act, please visit: http://www.dot.gov/privacy. You may review DOT's complete Privacy Act 
statement in the Federal Register published on April 11, 2000 (Volume 
65, Number 70; Pages 19477-78).

List of Subjects in 49 CFR Part 575

    Consumer protection, Motor vehicle safety, Reporting and 
recordkeeping requirements, Tires.

Proposed Regulatory Text

    For the foregoing reasons, NHTSA proposes to amend 49 CFR part 575 
as follows:

PART 575--CONSUMER INFORMATION

0
1. The authority citation for part 575 is revised to read as follows:

    Authority:  49 U.S.C. 32302, 32304A, 30111, 30115, 30117, 30123, 
30166, 30181, 30182, 30183, and 32908, Pub. L. 104-414, 114 Stat. 
1800, Pub. L. 109-59, 119 Stat. 1144, Pub. L. 110-140, 121 Stat. 
1492, Pub. L. 112-141, 126 Stat. 405, 15 U.S.C. 1232(g); delegation 
of authority at 49 CFR 1.95.
0
2. Amend Sec.  575.6 by removing paragraph (a)(2) and redesignating 
paragraphs (a)(3) through (5) as paragraphs (a)(2) through (4).
0
3. Add Subpart F to read as follows:

Subpart F--Moving Ahead for Progress in the 21st Century Act; 
Consumer Information

    Authority:  49 U.S.C. 30101 et. seq., Sec. 31306, Pub. L. 112-
141, 126 Stat. 405, delegation of authority at 49 CFR 1.95.


Sec.  575.501   Safety defect reporting

    (a) Purpose and scope. This section requires manufacturers of 
passenger motor vehicles to affix a label that describes the process 
for submitting a complaint about a safety-related motor vehicle defect 
to the National Highway Traffic Safety Administration. This section 
also requires manufacturers to include the same information in the 
owner's manual.
    (b) Application. This section applies to passenger motor vehicles 
under 10,000 lbs GVWR.
    (c) Required information-- (1) Label. (i) Each passenger motor 
vehicle must have a label permanently affixed to the passenger's sun 
visor. The label must not appear on the same side of the sun visor to 
which the sun visor air bag warning label is affixed, as required by 
S4.5.1(b)(5) of 49 CFR 571.208. The label must conform in content, 
form, and sequence to the label shown in Figure 1 of this section, and 
must comply with the following requirements:
    (A) The title must be in a bold black text.
    (B) The message area must have a white background and black text.
    (C) The pictograms must be black with a white background.
    (D) The label must be appropriately sized so that it is legible, 
visible, and prominent to the driver.
    (ii) When the safety defect reporting label required by paragraph 
(c)(1)(i) of this section and the air bag alert label required by 
S4.5.1(c) of 49 CFR 571.208 are affixed to the same side of the 
passenger's sun visor, the pictogram of the air bag alert label must be 
separated

[[Page 85488]]

from the pictograms of the safety defect reporting label by text and:
    (A) The labels must be located such that the shortest distance from 
any of the lettering or graphics on the safety defect reporting label 
to any of the lettering or graphics on the air bag alert label is not 
less than 3 cm, or
    (B) If the safety defect reporting and air bag alert labels are 
each surrounded by a continuous solid-lined border, the shortest 
distance from the border of the safety defect reporting label to the 
border of the air bag alert label must be not less than 1 cm.
    (iii) At the option of the manufacturer, the requirement in 
paragraph (c)(1)(i) of this section for a permanently affixed label may 
instead be met by permanent marking and molding of the required 
information onto the specified location.
    (2) Owner's Manual. (i) The manufacturer of each passenger motor 
vehicle must provide to the purchaser, in writing in the English 
language and not less than 10 point type, the following statement in 
the owner's manual, or, if there is no owner's manual or the owner's 
manual is electronic, on a one-page document:
    If you believe that your vehicle has a defect which could cause a 
crash or could cause injury or death, you should immediately inform the 
National Highway Traffic Safety Administration (NHTSA) in addition to 
notifying [INSERT NAME OF MANUFACTURER]. To contact NHTSA, you may call 
the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-
9153); go to http://www.safercar.gov; download the SaferCar mobile 
application; or write to: Administrator, NHTSA, 1200 New Jersey Ave. 
SE., Washington, DC 20590. You can also obtain other information about 
motor vehicle safety from http://www.safercar.gov.
    If NHTSA receives similar complaints, it may open an investigation, 
and if it finds that a safety defect exists in a group of vehicles, it 
may order a recall and remedy campaign. However, NHTSA cannot become 
involved in individual problems between you, your dealer, or [INSERT 
NAME OF MANUFACTURER].
    (ii) The manufacturer must specify in the table of contents of the 
owner's manual the location of the statement required in paragraph 
(c)(2)(i). The heading in the table of contents must state ``Reporting 
Safety Defects.''
[GRAPHIC] [TIFF OMITTED] TP28NO16.008


    Issued in Washington, DC.
Raymond R. Posten,
Associate Administrator for Rulemaking.
[FR Doc. 2016-28125 Filed 11-25-16; 8:45 am]
 BILLING CODE 4910-59-P


