
[Federal Register Volume 88, Number 233 (Wednesday, December 6, 2023)]
[Proposed Rules]
[Pages 84764-84767]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-26664]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2023-2230; Project Identifier MCAI-2023-00861-T]
RIN 2120-AA64


Airworthiness Directives; Deutsche Aircraft GmbH (Type 
Certificate Previously Held by 328 Support Services GmbH; AvCraft 
Aerospace GmbH; Fairchild Dornier GmbH; Dornier Luftfahrt GmbH) 
Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for all Deutsche Aircraft GmbH Model 328-100 and -300 airplanes. This 
proposed AD was prompted by operator reports of worn and ruptured 
bonding straps inside the feeder wing tanks and in both outer and inner 
wing tanks. This proposed AD would require a one-time detailed 
inspection of each affected part, and applicable corrective actions, as 
specified in a European Union Aviation Safety Agency (EASA) AD, which 
is proposed for incorporation by reference (IBR). The FAA is proposing 
this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by January 22, 
2024.

ADDRESSES: You may send comments, using the procedures found in 14 CFR

[[Page 84765]]

11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2023-2230; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For EASA material that is proposed for IBR in this AD, 
contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone 
+49 221 8999 000; email [email protected]; website easa.europa.eu. You 
may find this material on the EASA website at ad.easa.europa.eu. It is 
also available at regulations.gov under Docket No. FAA-2023-2230.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aviation Safety 
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone 206-231-3228; email [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2023-2230; Project Identifier 
MCAI-2023-00861-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to Todd 
Thompson, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 
410, Westbury, NY 11590; telephone 206-231-3228; email 
[email protected]. Any commentary that the FAA receives which is 
not specifically designated as CBI will be placed in the public docket 
for this rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2023-0137, dated July 12, 2023 (EASA 
AD 2023-0137) (also referred to as the MCAI), to correct an unsafe 
condition for all Deutsche Aircraft GmbH (Type Certificate previously 
held by 328 Support Services GmbH; AvCraft Aerospace GmbH; Fairchild 
Dornier GmbH; Dornier Luftfahrt GmbH) Model 328-100 and 328-300 
airplanes. The MCAI states that operators reported findings of damaged 
affected parts. The extent of the detected damage of the affected parts 
did not ensure that appropriately low electrical impedance is obtained 
and maintained through the affected bonding path. The unsafe condition, 
which if not detected and corrected, could lead to the loss of bonding 
function and, in combination with a lightning strike, create a source 
of ignition in a fuel tank, possibly resulting in a fire or explosion.
    The FAA is proposing this AD to address the unsafe condition.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2023-2230.

Related Service Information Under 1 CFR Part 51

    EASA AD 2023-0137 specifies procedures for a one-time detailed 
inspection of each affected part for worn and ruptured bonding straps, 
and applicable corrective actions (replacing the affected parts). This 
material is reasonably available because the interested parties have 
access to it through their normal course of business or by the means 
identified in ADDRESSES.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this NPRM after determining that 
the unsafe condition described previously is likely to exist or develop 
in other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2023-0137 described previously, except for any differences 
identified as exceptions in the regulatory text of this proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to incorporate EASA AD 2023-0137 by reference in the FAA 
final rule. This proposed AD would, therefore, require compliance with 
EASA AD 2023-0137 in its entirety through that incorporation, except 
for any differences identified as exceptions in the regulatory text of 
this proposed AD. Using common terms that are the same as the heading 
of a particular section in EASA AD 2023-0137 does not mean that 
operators need to comply only with that section. For example, where the 
AD requirement refers to ``all required actions and compliance times,''

[[Page 84766]]

compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2023-
0137. Service information required by EASA AD 2023-0137 for compliance 
will be available at regulations.gov under Docket No. FAA-2023-2230 
after the FAA final rule is published.

Interim Action

    The FAA considers that this proposed AD would be an interim action. 
If final action is later identified, the FAA might consider further 
rulemaking then.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 35 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
44 work-hours x $85 per hour = $3,740........................              $0           $3,740         $130,900
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary on-
condition actions that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need these on-condition actions:
    The FAA has received no definitive data on which to base the cost 
estimates for the on-condition actions specified in this proposed AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Deutsche Aircraft GmbH (Type Certificate Previously Held by 328 
Support Services GmbH; AvCraft Aerospace GmbH; Fairchild Dornier 
GmbH; Dornier Luftfahrt GmbH): Docket No. FAA-2023-2230; Project 
Identifier MCAI-2023-00861-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by January 22, 2024.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Deutsche Aircraft GmbH (Type Certificate 
previously held by 328 Support Services GmbH; AvCraft Aerospace 
GmbH; Fairchild Dornier GmbH; Dornier Luftfahrt GmbH) Model 328-100 
and 328-300 airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 28, Fuel.

(e) Unsafe Condition

    This AD was prompted by operator reports of worn and ruptured 
bonding straps inside the feeder wing tanks and in both outer and 
inner wing tanks. The FAA is issuing this AD to address damaged 
bonding straps. The unsafe condition, if not addressed, could result 
in the loss of bonding function and, in combination with a lightning 
strike, create a source of ignition in a fuel tank, possibly 
resulting in a fire or explosion and consequent loss of the 
airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2023-0137, dated July 12, 2023 (EASA AD 
2023-0137).

(h) Exceptions to EASA AD 2023-0137

    (1) Where EASA AD 2023-0137 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) This AD does not adopt the ``Remarks'' section of EASA AD 
2023-0137.
    (3) Where paragraph (2) of EASA AD 2023-0137 specifies if ``any 
damage is detected as defined in the ASB,'' this AD requires 
replacing those words with ``any worn or ruptured bonding strap is 
detected.''

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the manager of the 
International Validation Branch, mail it to the address identified 
in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify

[[Page 84767]]

your appropriate principal inspector, or lacking a principal 
inspector, the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Deutsche Aircraft GmbH's EASA 
Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.

(j) Additional Information

    For more information about this AD, contact Todd Thompson, 
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 206-231-3228; email 
[email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2023-0137, 
dated July 12, 2023.
    (ii) [Reserved]
    (3) For EASA AD 2023-0137, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; website easa.europa.eu. You may find this EASA 
AD on the EASA website at ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (5) You may view this material at the National Archives and 
Records Administration (NARA). For information on the availability 
of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected].

    Issued on November 29, 2023.
Victor Wicklund,
Deputy Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2023-26664 Filed 12-5-23; 8:45 am]
BILLING CODE 4910-13-P


