[Federal Register Volume 88, Number 134 (Friday, July 14, 2023)]
[Proposed Rules]
[Pages 45121-45123]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-14879]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2023-1493; Project Identifier MCAI-2022-01105-T]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc., Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Bombardier, Inc., Model BD-700-2A12 airplanes. This 
proposed AD was prompted by a report that some of the multi-function 
spoiler (MFS) anti-rotation plates failed in-service due to a thin wall 
design. This proposed AD would require replacing the MFS anti-rotation 
plates, inspecting the MFS anti-rotation plates for cracking and hinge 
bolts for evidence of rotation, accomplishing applicable corrective 
actions, and performing a functional test of the multi-function spoiler 
control surfaces. The FAA is proposing this AD to address the unsafe 
condition on these products.

DATES: The FAA must receive comments on this proposed AD by August 28, 
2023.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2023-1493; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For service information identified in this NPRM, contact 
Bombardier Business Aircraft Customer Response Center, 400 C[ocirc]te-
Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, Canada; telephone 514-
855-2999; email bombardier.com">[email protected]bombardier.com; website bombardier.com.
     You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th Street, Des Moines, WA. For information on the availability of 
this material at the FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Yaser Osman, Aviation Safety Engineer, 
FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-
228-7300; email [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2023-1493; Project Identifier 
MCAI-2022-01105-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
the proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

[[Page 45122]]

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to Yaser 
Osman, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 516-228-7300; email [email protected]. Any commentary that the FAA receives which is not 
specifically designated as CBI will be placed in the public docket for 
this rulemaking.

Background

    Transport Canada, which is the aviation authority for Canada, has 
issued Transport Canada AD CF-2022-47R1, dated October 11, 2022 
(Transport Canada AD CF-2022-47R1) (also referred to after this as the 
MCAI), to correct an unsafe condition on certain Bombardier, Inc., 
Model BD-700-2A12 airplanes. The MCAI states that a report was received 
that some of the MFS anti-rotation plates failed in-service due to a 
thin wall design. The MFS anti-rotation plates were designed with 
overlapping tolerances on the inside and outside diameters, which 
allows for an extremely thin wall thickness once machined.
    The FAA is proposing this AD to address MFS anti-rotation plate 
failures. The unsafe condition, if not addressed, could result in wear 
and failure of the inboard and outboard spoiler hinge pins possibly 
resulting in a hinge no longer supporting the load, or unintended 
asymmetrical spoiler deployment, leading to reduced controllability of 
the airplane, or loss of control of the airplane.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2023-1493.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Bombardier Service Bulletin 700-27-7504, Revision 
01, dated July 11, 2022. This service information specifies procedures 
for replacing the left and right MFS No. 1, MFS No. 2, and MFS No. 3 
anti-rotation plate part number (P/N) G05770140-103 and P/N G05770160-
101 with P/N G05770140-105. In addition, one of the procedural steps is 
to inspect the MFS anti-rotation plates for cracking and the hinge bolt 
for any evidence of rotation, and repair or replacement. This service 
information also specifies procedures for performing a functional test 
(stop-to-stop check) of the multi-function spoiler control-surfaces.
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with this State of Design Authority, 
it has notified the FAA of the unsafe condition described in the MCAI 
and service information described above. The FAA is issuing this NPRM 
after determining that the unsafe condition described previously is 
likely to exist or develop on other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in the service information already described. This proposed AD would 
also prohibit the installation of affected parts.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 42 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
3 work-hours x $85 per hour = $255...........................          $2,000           $2,255          $94,710
----------------------------------------------------------------------------------------------------------------

    The FAA has received no definitive data on which to base the cost 
estimates for the on-condition repairs or replacements specified in 
this proposed AD.
    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this proposed AD may be covered under warranty, thereby reducing the 
cost impact on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative,

[[Page 45123]]

on a substantial number of small entities under the criteria of the 
Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Bombardier, Inc.: Docket No. FAA-2023-1493; Project Identifier MCAI-
2022-01105-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by August 28, 2023.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc., Model BD-700-2A12 
airplanes, certificated in any category, serial numbers 70006 
through 70129 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code: 27, Flight 
controls.

(e) Unsafe Condition

    This AD was prompted by a report that some of the multi-function 
spoiler (MFS) anti-rotation plates failed in-service due to a thin 
wall design. The FAA is issuing this AD to address MFS anti-rotation 
plate failures. The unsafe condition, if not addressed, could result 
in wear and failure of the inboard and outboard spoiler hinge pins, 
possibly resulting in a hinge no longer supporting the load, or 
unintended asymmetrical spoiler deployment, leading to reduced 
controllability of the airplane, or loss of control of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Replacement and Inspection

    (1) Within 36 months after the effective date of this AD, 
replace the left and right MFS No. 1, MFS No. 2, and MFS No. 3 anti-
rotation plate part number (P/N) G05770140-103 and P/N G05770160-101 
with P/N G05770140-105, including inspecting the MFS anti-rotation 
plates for any cracking and the hinge bolts for any evidence of 
rotation, in accordance with the Part 2.B. of the Accomplishment 
Instructions of Bombardier Service Bulletin 700-27-7504, Revision 
01, dated July 11, 2022. If any cracking or evidence of rotation is 
found, before further flight, repair using a method approved in 
accordance with the procedures specified in paragraph (i)(1) of this 
AD.
    (2) Before further flight after accomplishing the actions 
specified in paragraph (g)(1) of this AD: Perform a functional test 
(stop-to-stop check) of the multi-function spoiler control-surfaces 
in accordance with the Step 2.C. (3) of the Accomplishment 
Instructions of Bombardier Service Bulletin 700-27-7504, Revision 
01, dated July 11, 2022.

(h) Credit for Previous Actions

    This paragraph provides credit for actions required by paragraph 
(g) of this AD, if those actions were performed before the effective 
date of this AD using Bombardier Service Bulletin 700-27-7504, dated 
March 2, 2022.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York ACO Branch, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or responsible Flight Standards Office, as appropriate. If 
sending information directly to the manager of the New York ACO 
Branch, mail it to ATTN: Program Manager, Continuing Operational 
Safety, at the address identified in paragraph (j)(2) of this AD or 
email to: [email protected]. If mailing information, also 
submit information by email. Before using any approved AMOC, notify 
your appropriate principal inspector, or lacking a principal 
inspector, the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, New York ACO 
Branch, FAA; or Transport Canada or Bombardier, Inc.'s Transport 
Canada Design Approval Organization (DAO). If approved by the DAO, 
the approval must include the DAO-authorized signature.

(j) Additional Information

    (1) Refer to Transport Canada AD CF-2022-47R1, dated October 11, 
2022, for related information. This Transport Canada AD may be found 
in the AD docket at regulations.gov under Docket No. FAA-2023-1493.
    (2) For more information about this AD, contact Yaser Osman, 
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 516-228-7300; email [email protected].
    (3) Service information identified in this AD that is not 
incorporated by reference is available at the addresses specified in 
paragraphs (k)(3) and (4) of this AD.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Service Bulletin 700-27-7504, Revision 01, dated 
July 11, 2022.
    (ii) [Reserved]
    (3) For service information identified in this AD, contact 
Bombardier Business Aircraft Customer Response Center, 400 
C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, Canada; 
telephone 514-855-2999; email bombardier.com">[email protected]bombardier.com; website 
bombardier.com.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th Street, Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, email [email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on July 8, 2023.
Michael Linegang,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2023-14879 Filed 7-13-23; 8:45 am]
BILLING CODE 4910-13-P


