[Federal Register Volume 88, Number 61 (Thursday, March 30, 2023)]
[Proposed Rules]
[Pages 19021-19024]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-06493]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2023-0656; Project Identifier MCAI-2022-01433-T]
RIN 2120-AA64
Airworthiness Directives; Airbus SAS Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for all Airbus SAS Model A350-941 and -1041 airplanes. This proposed AD
was prompted by reports of a non-full life clearance in the low-
pressure hydraulic pipes of the nose landing gear return line, due to
two quality escapes. This proposed AD would require replacing
[[Page 19022]]
the affected aluminum pipes with titanium pipes, as specified in a
European Union Aviation Safety Agency (EASA) AD, which is proposed for
incorporation by reference (IBR). This proposed AD would also prohibit
the installation of affected parts. The FAA is proposing this AD to
address the unsafe condition on these products.
DATES: The FAA must receive comments on this proposed AD by May 15,
2023.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to regulations.gov. Follow
the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket: You may examine the AD docket at regulations.gov under
Docket No. FAA-2023-0656; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this NPRM, the mandatory continuing airworthiness
information (MCAI), any comments received, and other information. The
street address for Docket Operations is listed above.
Material Incorporated by Reference:
For material that is proposed for IBR in this NPRM,
contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone
+49 221 8999 000; email [email protected]; website easa.europa.eu. You
may find this material on the EASA website at ad.easa.europa.eu. It is
also available at regulations.gov under Docket No. FAA-2023-0656.
You may view this service information at the FAA,
Airworthiness Products Section, Operational Safety Branch, 2200 South
216th Street, Des Moines, WA. For information on the availability of
this material at the FAA, call 206-231-3195.
FOR FURTHER INFORMATION CONTACT: Dat Le, Aerospace Engineer, Large
Aircraft Section, FAA, International Validation Branch, 2200 South
216th Street, Des Moines, WA 98198; telephone 516-228-7317; email:
[email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under ADDRESSES. Include ``Docket No. FAA-2023-0656; Project Identifier
MCAI-2022-01433-T'' at the beginning of your comments. The most helpful
comments reference a specific portion of the proposal, explain the
reason for any recommended change, and include supporting data. The FAA
will consider all comments received by the closing date and may amend
this proposal because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
regulations.gov, including any personal information you provide. The
agency will also post a report summarizing each substantive verbal
contact received about this NPRM.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to Dat
Le, Aerospace Engineer, Large Aircraft Section, FAA, International
Validation Branch, 2200 South 216th Street, Des Moines, WA 98198;
telephone 516-228-7317; email: [email protected]. Any commentary that
the FAA receives which is not specifically designated as CBI will be
placed in the public docket for this rulemaking.
Background
EASA, which is the Technical Agent for the Member States of the
European Union, has issued EASA AD 2022-0217R1, dated March 1, 2023
(EASA AD 2022-0217R1) (also referred to as the MCAI), to correct an
unsafe condition for all Airbus SAS Model A350-941 and -1041 airplanes.
The MCAI states Airbus received reports from the manufacturer of a non-
full life clearance in the low-pressure hydraulic pipes of the nose
landing gear return line, due to two separate quality escapes. One
quality escape occurred when after alodine process application on
aluminum pipes, black spots and stains caused by corrosion pitting were
found on inner and outer diameters. In a second quality escape,
aluminum pipes were identified with an average ovality value (which
measures the maximum and minimum outer diameter of the pipe) above the
admissible value. This condition, if not corrected, could lead to a
premature rupture in the yellow hydraulic line, which, in case of
additional independent system failures, could result in reduced
airplane controllability.
The FAA is proposing this AD to address the unsafe condition on
these products. You may examine the MCAI in the AD docket at
regulations.gov under Docket No. FAA-2023-0656.
Related Service Information Under 1 CFR Part 51
EASA AD 2022-0217R1 specifies procedures for replacing the affected
aluminum pipes with titanium pipes. EASA AD 2022-0217R1 also prohibits
the installation of affected parts.
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in ADDRESSES.
FAA's Determination
This product has been approved by the aviation authority of another
country and is approved for operation in the United States. Pursuant to
the FAA's bilateral agreement with the State of Design Authority, it
has notified the FAA of the unsafe condition described in the MCAI
described above. The FAA is issuing this NPRM after determining that
the unsafe condition described previously is likely to exist or develop
in other products of the same type designs.
Proposed AD Requirements in This NPRM
This proposed AD would require accomplishing the actions specified
in EASA AD 2022-0217R1 described previously, except for any differences
identified as exceptions in the regulatory text of this proposed AD.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA developed a process to use some civil aviation
authority (CAA) ADs as the primary source of information for compliance
with
[[Page 19023]]
requirements for corresponding FAA ADs. The FAA has been coordinating
this process with manufacturers and CAAs. As a result, the FAA proposes
to incorporate EASA AD 2922-0217R1 by reference in the FAA final rule.
This proposed AD would, therefore, require compliance with EASA AD
2022-0217R1 in its entirety through that incorporation, except for any
differences identified as exceptions in the regulatory text of this
proposed AD. Using common terms that are the same as the heading of a
particular section in EASA AD 2022-0217R1 does not mean that operators
need comply only with that section. For example, where the AD
requirement refers to ``all required actions and compliance times,''
compliance with this AD requirement is not limited to the section
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2022-
0217R1. Service information required by EASA AD 2022-0217R1 for
compliance will be available at regulations.gov under Docket No. FAA-
2023-0656 after the FAA final rule is published.
Costs of Compliance
The FAA estimates that this AD, if adopted as proposed, would
affect 24 airplanes of U.S. registry. The FAA estimates the following
costs to comply with this proposed AD:
Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
Labor cost Parts cost Cost per product Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Up to 130 work-hours x $85 per Up to $16,500............ Up to $27,550............ Up to $661,200.
hour = $11,050.
----------------------------------------------------------------------------------------------------------------
The FAA has included all known costs in its cost estimate.
According to the manufacturer, however, some or all of the costs of
this proposed AD may be covered under warranty, thereby reducing the
cost impact on affected operators.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Would not affect intrastate aviation in Alaska, and
(3) Would not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
Airbus SAS: Docket No. FAA-2023-0656; Project Identifier MCAI-2022-
01433-T.
(a) Comments Due Date
The FAA must receive comments on this airworthiness directive
(AD) by May 15, 2023.
(b) Affected ADs
None.
(c) Applicability
This AD applies to all Airbus SAS Model A350-0941 and -1041
airplanes, certificated in any category.
(d) Subject
Air Transport Association (ATA) of America Code: 29, Hydraulic
Power.
(e) Unsafe Condition
This AD was prompted by reports of a non-full life clearance in
the low-pressure hydraulic pipes of the nose landing gear return
line within the yellow hydraulic line system, due to two quality
escapes. The FAA is issuing this AD to address the quality escapes
in the manufacture of these pipes. The unsafe condition, if not
addressed, could result in premature rupture in the yellow hydraulic
line, which, in case of additional independent system failures,
could result in reduced airplane controllability.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, European Union Aviation Safety Agency (EASA) AD
2022-0217R1, dated March 1, 2023 (EASA AD 2022-0217R1).
(h) Exceptions to EASA AD 2022-0217R1
(1) Where EASA AD 2022-0217R1 refers to its effective date, this
AD requires using the effective date of this AD.
(2) This AD does not adopt the ``Remarks'' section of EASA AD
2022-0217R1.
(3) Where EASA AD 2022-0217R1 refers to November 18, 2022 (the
effective date of EASA AD 2022-0217), this AD requires using the
effective date of this AD.
(i) Additional AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Validation Branch, FAA, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19. In accordance with 14 CFR 39.19, send your request to your
principal inspector or responsible Flight Standards Office, as
appropriate. If sending information directly to the manager of the
certification office, send it to the attention of the person
identified in paragraph (j) of this AD.
[[Page 19024]]
Information may be emailed to: [email protected]. Before
using any approved AMOC, notify your appropriate principal
inspector, or lacking a principal inspector, the manager of the
responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions from a manufacturer, the instructions must be
accomplished using a method approved by the Manager, International
Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design
Organization Approval (DOA). If approved by the DOA, the approval
must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by
paragraph (i)(2) of this AD, if any service information contains
procedures or tests that are identified as RC, those procedures and
tests must be done to comply with this AD; any procedures or tests
that are not identified as RC are recommended. Those procedures and
tests that are not identified as RC may be deviated from using
accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC, provided
the procedures and tests identified as RC can be done and the
airplane can be put back in an airworthy condition. Any
substitutions or changes to procedures or tests identified as RC
require approval of an AMOC.
(j) Additional Information
For more information about this AD, contact Dat Le, Aerospace
Engineer, Large Aircraft Section, FAA, International Validation
Branch, 2200 South 216th Street, Des Moines, WA 98198; telephone 516
228 7317; email: [email protected].
(k) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless this AD specifies otherwise.
(i) European Union Aviation Safety Agency (EASA) AD 2022-0217R1,
dated March 1, 2023.
(ii) [Reserved]
(3) For EASA AD 2022-0217R1, contact EASA, Konrad-Adenauer-Ufer
3, 50668 Cologne, Germany; telephone +49 221 8999 000; email
[email protected]; website easa.europa.eu. You may find this EASA
AD on the EASA website at ad.easa.europa.eu.
(4) You may view this service information at the FAA,
Airworthiness Products Section, Operational Safety Branch, 2200
South 216th Street, Des Moines, WA. For information on the
availability of this material at the FAA, call 206-231-3195.
(5) You may view this service information that is incorporated
by reference at the National Archives and Records Administration
(NARA). For information on the availability of this material at
NARA, email [email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.
Issued on March 24, 2023.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft
Certification Service.
[FR Doc. 2023-06493 Filed 3-29-23; 8:45 am]
BILLING CODE 4910-13-P