[Federal Register Volume 88, Number 67 (Friday, April 7, 2023)]
[Rules and Regulations]
[Pages 20741-20743]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-07092]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-1651; Project Identifier MCAI-2022-00893-T; 
Amendment 39-22360; AD 2023-04-13]
RIN 2120-AA64


Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is superseding Airworthiness Directive (AD) 2021-04-
02, which applied to certain Dassault Aviation Model FALCON 2000EX 
airplanes. AD 2021-04-02 required revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations. This AD was prompted by a 
determination that new or more restrictive airworthiness limitations 
are necessary. This AD continues to require the actions in AD 2021-04-
02, and also requires revising the existing maintenance or inspection 
program, as applicable, to incorporate new or more restrictive 
airworthiness limitations, as specified in a European Union Aviation 
Safety Agency (EASA) AD, which is incorporated by reference (IBR). The 
FAA is issuing this AD to address the unsafe condition on these 
products.

DATES: This AD is effective May 12, 2023.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of May 12, 
2023.
    The Director of the Federal Register approved the incorporation by 
reference of a certain other publication listed in this AD as of March 
30, 2021 (86 FR 10738, February 23, 2021).

ADDRESSES: 
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2022-1651; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this final rule, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.
    Material Incorporated by Reference:
     For material incorporated by reference in this AD, contact 
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; website easa.europa.eu. You may 
find this material on the EASA website at ad.easa.europa.eu.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available in the AD docket at 
regulations.gov under Docket No. FAA-2022-1651.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
Large Aircraft Section, International Validation Branch, FAA, 2200 
South 216th St., Des Moines, WA 98198; telephone 206-231-3226; email 
[email protected].

SUPPLEMENTARY INFORMATION: 

Background

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 to supersede AD 2021-04-02, Amendment 39-21423 (86 FR 
10738, February 23, 2021) (AD 2021-04-02). AD 2021-04-02 applied to 
certain Dassault Aviation Model FALCON 2000EX airplanes. AD 2021-04-02 
required revising the existing maintenance or inspection program, as 
applicable, to incorporate new or more restrictive airworthiness 
limitations. The FAA issued AD 2021-04-02 to address reduced structural 
integrity of the airplane. AD 2021-04-02 specified that accomplishing 
the revision required by paragraph (g) or (i) of that AD terminates the 
requirements of paragraph (g)(1) of AD 2010-26-05, Amendment 39-16544 
(75 FR 79952, December 21, 2010), for Dassault Aviation Model FALCON 
2000EX airplanes.
    The NPRM published in the Federal Register on December 23, 2022 (87 
FR 78878). The NPRM was prompted by AD 2022-0136, dated July 6, 2022, 
issued by EASA, which is the Technical Agent for the Member States of 
the European Union (EASA AD 2022-0136) (referred to after this as the 
MCAI). The MCAI states that new or more restrictive airworthiness 
limitations have been developed.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2022-1651.
    In the NPRM, the FAA proposed to continue to require the actions in 
AD 2021-04-02, and to require revising the existing maintenance or 
inspection program, as applicable, to incorporate additional new or 
more restrictive airworthiness limitations, as specified in EASA AD 
2022-0136.

Discussion of Final Airworthiness Directive

Comments

    The FAA received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA reviewed the relevant data and determined 
that air safety requires adopting this AD as proposed. Accordingly, the 
FAA is issuing this AD to address the unsafe condition on this product. 
Except for minor editorial changes, this AD is adopted as proposed in 
the NPRM. None of the changes will increase the economic burden on any 
operator.

Related Service Information Under 1 CFR Part 51

    EASA AD 2022-0136 specifies new or more restrictive airworthiness 
limitations for airplane structures and safe life limits.
    This AD also requires EASA AD 2020-0114, dated May 20, 2020, which 
the Director of the Federal Register approved for incorporation by 
reference as of March 30, 2021 (86 FR 10738, February 23, 2021).
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 245 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:
    The FAA estimates the total cost per operator for the retained 
actions from AD 2021-04-02 to be $7,650 (90 work-hours x $85 per work-
hour).
    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-

[[Page 20742]]

hours per operator, although the agency recognizes that this number may 
vary from operator to operator. In the past, the agency has estimated 
that this action takes 1 work-hour per airplane. Since operators 
incorporate maintenance or inspection program changes for their 
affected fleet(s), the FAA has determined that a per-operator estimate 
is more accurate than a per-airplane estimate.
    The FAA estimates the total cost per operator for the new actions 
to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by:
0
a. Removing Airworthiness Directive (AD) 2021-04-02, Amendment 39-21423 
(86 FR 10738, February 23, 2021); and
0
b. Adding the following new AD:

2023-04-13 Dassault Aviation: Amendment 39-22360; Docket No. FAA-
2022-1651; Project Identifier MCAI-2022-00893-T.

(a) Effective Date

    This airworthiness directive (AD) is effective May 12, 2023.

(b) Affected ADs

    (1) This AD replaces AD 2021-04-02, Amendment 39-21423 (86 FR 
10738, February 23, 2021) (AD 2021-04-02).
    (2) This AD affects AD 2010-26-05, Amendment 39-16544 (75 FR 
79952, December 21, 2010) (AD 2010-26-05).

(c) Applicability

    This AD applies to Dassault Aviation Model FALCON 2000EX 
airplanes, certificated in any category, with an original 
airworthiness certificate or original export certificate of 
airworthiness issued on or before January 15, 2022.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Unsafe Condition

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
issuing this AD to address reduced structural integrity of the 
airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Retained Maintenance or Inspection Program Revision, With No 
Changes

    This paragraph restates the requirements of paragraph (i) of AD 
2021-04-02, with no changes. For airplanes with an original 
airworthiness certificate or original export certificate of 
airworthiness issued on or before February 15, 2020, except as 
specified in paragraph (h) of this AD: Comply with all required 
actions and compliance times specified in, and in accordance with, 
European Union Aviation Safety Agency (EASA) AD 2020-0114, dated May 
20, 2020 (EASA AD 2020-0114). Accomplishing the revision of the 
existing maintenance or inspection program required by paragraph (j) 
of this AD terminates the requirements of this paragraph.

(h) Retained Exceptions to EASA AD 2020-0114, With No Changes

    This paragraph restates the exceptions specified in paragraph 
(j) of AD 2021-04-02, with no changes.
    (1) The requirements specified in paragraphs (1) and (2) of EASA 
AD 2020-0114 do not apply to this AD.
    (2) Paragraph (3) of EASA AD 2020-0114 specifies revising ``the 
approved AMP'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, to incorporate the ``limitations, tasks and 
associated thresholds and intervals'' specified in paragraph (3) of 
EASA AD 2020-0114 within 90 days after March 30, 2021 (the effective 
date of AD 2021-04-02).
    (3) The initial compliance time for doing the tasks specified in 
paragraph (3) of EASA AD 2020-0114 is at the applicable ``associated 
thresholds'' specified in paragraph (3) of EASA AD 2020-0114, or 
within 90 days after the March 30, 2021 (the effective date of AD 
2021-04-02), whichever occurs later.
    (4) The provisions specified in paragraphs (4) and (5) of EASA 
AD 2020-0114 do not apply to this AD.
    (5) The ``Remarks'' section of EASA AD 2020-0114 does not apply 
to this AD.

(i) Retained Provision: No Alternative Actions or Intervals, With a New 
Exception

    This paragraph restates the requirements of paragraph (k) of AD 
2021-04-02, with a new exception. Except as required by paragraph 
(j) of this AD, after the existing maintenance or inspection program 
has been revised as required by paragraph (g) of this AD, no 
alternative actions (e.g., inspections) or intervals may be used 
unless they are approved as specified in the provisions of the 
``Ref. Publications'' section of EASA AD 2020-0114.

(j) New Maintenance or Inspection Program Revision

    Except as specified in paragraph (k) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2022-0136, dated July 6, 2022 (EASA AD 
2022-0136). Accomplishing the revision of the existing maintenance 
or inspection program required by this paragraph terminates the 
requirements of paragraph (g) of this AD.

(k) Exceptions to EASA AD 2022-0136

    (1) The requirements specified in paragraphs (1) and (2) of EASA 
AD 2022-0136 do not apply to this AD.
    (2) Paragraph (3) of EASA AD 2022-0136 specifies revising ``the 
approved AMP'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, within 90 days after the effective date of this AD.

[[Page 20743]]

    (3) The initial compliance time for doing the tasks specified in 
paragraph (3) of EASA AD 2022-0136 is at the applicable 
``limitation'' and ``associated thresholds'' as incorporated by the 
requirements of paragraph (3) of EASA AD 2022-0136, or within 90 
days after the effective date of this AD, whichever occurs later.
    (4) The provisions specified in paragraphs (4) and (5) of EASA 
AD 2022-0136 do not apply to this AD.
    (5) The ``Remarks'' section of EASA AD 2022-0136 does not apply 
to this AD.

(l) New Provisions for Alternative Actions and Intervals

    After the maintenance or inspection program has been revised as 
required by paragraph (j) of this AD, no alternative actions (e.g., 
inspections), and intervals are allowed unless they are approved as 
specified in the provisions of the ``Ref. Publications'' section of 
EASA AD 2022-0136.

(m) Terminating Action for Certain Actions in AD 2010-26-05

    Accomplishing the actions required by paragraph (g) or (j) of 
this AD terminates the requirements of paragraph (g)(1) of AD 2010-
26-05, for Dassault Aviation Model FALCON 2000EX airplanes only.

(n) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the International 
Validation Branch, send it to the attention of the person identified 
in paragraph (o) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Dassault Aviation's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.

(o) Additional Information

    For more information about this AD, contact Tom Rodriguez, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
206-231-3226; email [email protected].

(p) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (3) The following service information was approved for IBR on 
May 12, 2023.
    (i) European Union Aviation Safety Agency (EASA) AD 2022-0136, 
dated July 6, 2022.
    (ii) [Reserved]
    (4) The following service information was approved for IBR on 
March 30, 2021 (86 FR 10738, February 23, 2021).
    (i) European Union Aviation Safety Agency (EASA) AD 2020-0114, 
dated May 20, 2020.
    (ii) [Reserved]
    (5) For EASA ADs 2020-0114 and 2022-0136, contact EASA, Konrad-
Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; 
email [email protected]; website easa.europa.eu. You may find these 
EASA ADs on the EASA website at ad.easa.europa.eu.
    (6) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (7) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on February 17, 2023.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2023-07092 Filed 4-6-23; 8:45 am]
BILLING CODE 4910-13-P


