[Federal Register Volume 88, Number 43 (Monday, March 6, 2023)]
[Rules and Regulations]
[Pages 13671-13673]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-04466]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-1580; Project Identifier MCAI-2022-00808-T; 
Amendment 39-22354; AD 2023-04-07]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Airbus SAS Model A350-941 and -1041 airplanes. This AD was 
prompted by a determination that the surface protection is missing 
between certain aluminum brackets and the struts to which they are 
attached in the flight deck air distribution system. This AD requires 
applying surface protection to the affected aluminum brackets and 
struts, as specified in a European Union Aviation Safety Agency (EASA) 
AD, which is incorporated by reference. This AD also prohibits 
modifying an airplane using certain service information. The FAA is 
issuing this AD to address the unsafe condition on these products.

DATES: This AD is effective April 10, 2023.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of April 10, 
2023.

ADDRESSES: 
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2022-1580; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this final rule, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.
    Material Incorporated by Reference:
     For material incorporated by reference in this AD, contact 
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; website easa.europa.eu. You may 
find this material on the EASA website at ad.easa.europa.eu.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available in the AD docket at 
regulations.gov under Docket No. FAA-2022-1580.

FOR FURTHER INFORMATION CONTACT: Dat Le, Aerospace Engineer, Large 
Aircraft Section, FAA, International Validation Branch, 2200 South 
216th St., Des Moines, WA 98198; telephone 516-228-7317; email 
[email protected].

SUPPLEMENTARY INFORMATION:

Background

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to certain Airbus SAS 
Model A350-941 and -1041 airplanes. The NPRM published in the Federal 
Register on December 13, 2022 (87 FR 76160). The NPRM was prompted by 
AD 2022-0119, dated June 21, 2022, issued by EASA, which is the 
Technical Agent for the Member States of the European Union (EASA AD 
2022-0119) (also referred to as the MCAI). The MCAI states that the 
surface protection was determined to be missing between certain 
aluminum brackets and the struts to which they are attached in the 
flight deck air distribution system. The affected parts were installed 
either in production through Airbus modification 109229 or 109230, or 
in-service through accomplishing the original issue of Airbus Service 
Bulletin A350-21-P031; or the original issue of Airbus Service Bulletin 
A350-21-P032. This condition, if not corrected, could lead to rupture 
of the associated ducting, reducing the efficiency of the flight deck 
air distribution system, which, in combination with smoke in the flight 
deck, could result in impaired flightcrew capability to control the 
airplane.
    In the NPRM, the FAA proposed to require applying surface 
protection to the affected aluminum brackets and struts, as specified 
in EASA AD 2022-0119. The NPRM also proposed to prohibit modifying an 
airplane using certain service information. The FAA is issuing this AD 
to address the unsafe condition on these products.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2022-1580.

Discussion of Final Airworthiness Directive

Comments

    The FAA received a comment from The Air Line Pilots Association, 
International (ALPA) who supported the NPRM without change.

Conclusion

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA reviewed the relevant data, considered the 
comment received, and determined that air safety requires adopting this 
AD as proposed. Accordingly, the FAA is issuing this AD to address the 
unsafe condition on this product. Except for minor editorial changes, 
this AD is adopted as proposed in the NPRM. None of the changes will 
increase the economic burden on any operator.

Related Service Information Under 1 CFR Part 51

    EASA AD 2022-0119 specifies procedures for applying surface 
protection to aluminum brackets and struts at frame (FR) 22 and FR 24, 
as applicable, in zone C2-2 forward section. EASA AD 2020-0119 also 
prohibits modifying an airplane using certain service information. This 
material is reasonably available because the interested parties have 
access to it through their normal course of business or by the means 
identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 30 airplanes of U.S. 
registry. The

[[Page 13672]]

FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
8 work-hours x $85 per hour = $680...........................          $1,350           $2,030          $60,900
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2023-04-07 Airbus SAS: Amendment 39-22354; Docket No. FAA-2022-1580; 
Project Identifier MCAI-2022-00808-T.

(a) Effective Date

    This airworthiness directive (AD) is effective April 10, 2023.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A350-941 and -1041 
airplanes, certificated in any category, as identified in European 
Union Aviation Safety Agency (EASA) AD 2022-0119, dated June 21, 
2022 (EASA AD 2022-0119).

(d) Subject

    Air Transport Association (ATA) of America Code 21, Air 
conditioning.

(e) Unsafe Condition

    This AD was prompted by a determination that the surface 
protection is missing between certain aluminum brackets and the 
struts to which they are attached in the flight deck air 
distribution system. The FAA is issuing this AD to address missing 
aluminum bracket surface protection. This condition, if not 
corrected, could lead to rupture of the associated ducting, reducing 
the efficiency of the flight deck air distribution system, which, in 
combination with smoke in the flight deck, could result in impaired 
flightcrew capability to control the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2022-0119.

(h) Exceptions to EASA AD 2022-0119

    (1) Where EASA AD 2022-0119 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) This AD does not adopt the ``Remarks'' section of EASA AD 
2022-0119.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the International 
Validation Branch, send it to the attention of the person identified 
in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (i)(2) of this AD, if any service information contains 
procedures or tests that are identified as RC, those procedures and 
tests must be done to comply with this AD; any procedures or tests 
that are not identified as RC are recommended. Those procedures and 
tests that are not identified as RC may be deviated from using 
accepted methods in accordance with the operator's maintenance or 
inspection program without obtaining approval of an AMOC, provided 
the procedures and tests identified as RC can be done and the 
airplane can be put back in an airworthy condition. Any 
substitutions or changes to procedures or tests identified as RC 
require approval of an AMOC.

(j) Additional Information

    For more information about this AD, contact Dat Le, Aerospace 
Engineer, Large Aircraft Section, FAA, International Validation 
Branch, 2200 South 216th St., Des Moines, WA 98198; telephone 516-
228-7317; email [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.

[[Page 13673]]

    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2022-0119, 
dated June 21, 2022.
    (ii) [Reserved]
    (3) For EASA AD 2022-0119, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; website easa.europa.eu. You may find this EASA 
AD on the EASA website at ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on February 16, 2023.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2023-04466 Filed 3-3-23; 8:45 am]
BILLING CODE 4910-13-P


