[Federal Register Volume 87, Number 238 (Tuesday, December 13, 2022)]
[Proposed Rules]
[Pages 76158-76160]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-26933]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-1417; Project Identifier AD-2022-00731-T]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for all The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. 
This proposed AD was prompted by reports of a loss of water pressure 
during flight and water leaks that affected multiple pieces of 
electronic equipment. This proposed AD would require a detailed visual 
inspection of all door 1 and door 3 lavatory and galley potable water 
systems for any missing or incorrectly installed clamshell couplings 
and applicable on-condition actions. The FAA is proposing this AD to 
address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by January 27, 
2023.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2022-1417; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, any comments received, and other 
information. The street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For service information identified in this NPRM, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; website myboeingfleet.com. It is also available 
at regulations.gov by searching for and locating Docket No. FAA-2022-
1417.
     You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Courtney Tuck, Aerospace Engineer, 
Cabin Safety and Environmental Systems Section, FAA, Seattle ACO 
Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206-
231-3986; email: [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2022-1417; Project Identifier 
AD-2022-00731-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Courtney Tuck, Aerospace Engineer, Cabin Safety and Environmental 
Systems Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des 
Moines, WA 98198; phone and fax: 206-231-3986; email: 
[email protected]. Any commentary that the FAA receives that is 
not specifically designated as CBI will be placed in the public docket 
for this rulemaking.

Background

    The FAA has received reports of a loss of water pressure during 
flight and water leaks that affected multiple pieces of electronic 
equipment. One operator reported a significant water leak due to a 
loose potable water system hose caused by an incorrectly installed 
clamshell coupling within the lavatory. Another operator reported a 
water leak due to a detached clamshell coupling below the Door 1 
forward center galley countertop adjacent to the gray water interface 
valve (GWIV) maintenance access compartment. The findings include a 
loss of water pressure during flight and a potable water system leak, 
discovered after landing, that caused water to migrate into the forward 
electronic equipment (EE) bay and affect multiple pieces of electronic 
equipment. In addition, water pressure was lost during flight. 
Incorrectly installed or missing lavatory and galley clamshell 
couplings, if not addressed, could result in water leaks and water 
migration to critical flight equipment, which may affect the continued 
safe flight and landing of the airplane.

FAA's Determination

    The FAA is issuing this NPRM after determining that the unsafe 
condition described previously is likely to exist or develop on other 
products of the same type design.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Boeing Alert Requirements Bulletin B787-81205-
SB380021-00 RB, Issue 001, dated August 12, 2022. This service 
information specifies procedures for a detailed visual inspection of 
all door 1

[[Page 76159]]

and door 3 lavatory and galley potable water systems for any missing or 
incorrectly installed clamshell couplings and applicable on-condition 
actions. On-condition actions include installing clamshell couplings, 
doing a leak test, and performing corrective actions until the leak 
test is passed.
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in ADDRESSES.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in the service information already described except for any differences 
identified as exceptions in the regulatory text of this proposed AD. 
For information on the procedures and compliance times, see this 
service information at regulations.gov by searching for and locating 
Docket No. FAA-2022-1417.

Interim Action

    The FAA considers that this proposed AD would be an interim action. 
If a final action is later identified, the FAA might consider further 
rulemaking.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 134 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
              Action U.S.                      Labor cost           Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Detailed visual inspection (DVI) (per   1 work-hour x $85 per                 $0             $85         $11,390
 lavatory or galley).                    hour = $85.
----------------------------------------------------------------------------------------------------------------

    The FAA has received no definitive data on which to base the cost 
estimates for the on-condition actions specified in this proposed AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

The Boeing Company: Docket No. FAA-2022-1417; Project Identifier AD-
2022-00731-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by January 27, 2023.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all The Boeing Company Model 787-8, 787-9, 
and 787-10 airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 38, Water/waste.

(e) Unsafe Condition

    This AD was prompted by reports of a loss of water pressure 
during flight and water leaks that affected multiple pieces of 
electronic equipment. The FAA is issuing this AD to address 
incorrectly installed or missing lavatory and galley clamshell 
couplings that could lead to water leaks and water migration to 
critical flight equipment, which may affect the continued safe 
flight and landing of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as specified by paragraph (h) of this AD: At the 
applicable times specified in the ``Compliance'' paragraph of Boeing 
Alert Requirements Bulletin B787-81205-SB380021-00 RB, Issue 001, 
dated August 12, 2022, do all applicable actions identified in, and 
in accordance with, the Accomplishment Instructions of Boeing Alert 
Requirements Bulletin B787-81205-SB380021-00 RB, Issue 001, dated 
August 12, 2022.
    Note 1 to paragraph (g): Guidance for accomplishing the actions 
required by this AD can be found in Boeing Alert Service Bulletin 
B787-81205-SB380021-00, Issue 001, dated August 12, 2022, which is 
referred to in Boeing Alert Requirements Bulletin B787-81205-
SB380021-00 RB, Issue 001, dated August 12, 2022.

(h) Exceptions to Service Information Specifications

    Where the Compliance Time columns of the table in the 
``Compliance'' paragraph of Boeing Alert Requirements Bulletin B787-
81205-SB380021-00 RB, Issue 001, dated August 12, 2022, uses the 
phrase ``the Issue 001 date of Requirements Bulletin B787-81205-
SB380021-00 RB,'' this AD requires using ``the effective date of 
this AD.''

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO Branch, FAA, has the authority to 
approve AMOCs

[[Page 76160]]

for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the manager of the 
certification office, send it to the attention of the person 
identified in paragraph (j) of this AD. Information may be emailed 
to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the responsible Flight Standards Office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by The Boeing Company Organization Designation 
Authorization (ODA) that has been authorized by the Manager, Seattle 
ACO Branch, FAA, to make those findings. To be approved, the repair 
method, modification deviation, or alteration deviation must meet 
the certification basis of the airplane, and the approval must 
specifically refer to this AD.

(j) Related Information

    For more information about this AD, contact Courtney Tuck, 
Aerospace Engineer, Cabin Safety and Environmental Systems Section, 
FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; 
phone and fax: 206-231-3986; email: [email protected]

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Boeing Alert Requirements Bulletin B787-81205-SB380021-00 
RB, Issue 001, dated August 12, 2022.
    (ii) [Reserved]
    (3) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; website myboeingfleet.com.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, [email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on November 3, 2022.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2022-26933 Filed 12-12-22; 8:45 am]
BILLING CODE 4910-13-P


