[Federal Register Volume 87, Number 180 (Monday, September 19, 2022)]
[Rules and Regulations]
[Pages 57139-57142]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-20146]



 ========================================================================
 Rules and Regulations
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains regulatory documents 
 having general applicability and legal effect, most of which are keyed 
 to and codified in the Code of Federal Regulations, which is published 
 under 50 titles pursuant to 44 U.S.C. 1510.
 
 The Code of Federal Regulations is sold by the Superintendent of Documents. 
 
 ========================================================================
 

  Federal Register / Vol. 87, No. 180 / Monday, September 19, 2022 / 
Rules and Regulations  

[[Page 57139]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-1156; Project Identifier MCAI-2021-01024-T; 
Amendment 39-22175; AD 2022-19-06]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Airbus SAS Model A310 series airplanes. This AD was prompted by a 
determination that new or more restrictive airworthiness tasks are 
necessary. This AD requires revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness tasks, as specified in a European Union 
Aviation Safety Agency (EASA) AD, which is incorporated by reference. 
The FAA is issuing this AD to address the unsafe condition on these 
products.

DATES: This AD is effective October 4, 2022.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of October 4, 
2022.
    The FAA must receive comments on this AD by November 3, 2022.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.

AD Docket

    You may examine the AD docket at regulations.gov under Docket No. 
FAA-2022-1156; or in person at Docket Operations between 9 a.m. and 5 
p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this final rule, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.

Material Incorporated by Reference

     For material incorporated by reference (IBR) in this AD, 
contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone 
+49 221 8999 000; email [email protected]; website easa.europa.eu. You 
may find this material on the EASA website at ad.easa.europa.eu.
     You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, Large 
Aircraft Section, International Validation Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone 206-231-3225; email 
[email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    The FAA invites you to send any written data, views, or arguments 
about this final rule. Send your comments to an address listed under 
ADDRESSES. Include ``Docket No. FAA-2022-1156; Project Identifier MCAI-
2021-01024-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the final rule, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this final rule because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this final rule.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this AD contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this final rule, it is important that you clearly designate the 
submitted comments as CBI. Please mark each page of your submission 
containing CBI as ``PROPIN.'' The FAA will treat such marked 
submissions as confidential under the FOIA, and they will not be placed 
in the public docket of this final rule. Submissions containing CBI 
should be sent to Dan Rodina, Aerospace Engineer, Large Aircraft 
Section, International Validation Branch, FAA, 2200 South 216th St., 
Des Moines, WA 98198; telephone 206-231-3225; email [email protected]. 
Any commentary that the FAA receives which is not specifically 
designated as CBI will be placed in the public docket for this 
rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2021-0205, dated September 14, 2021 
(EASA AD 2021-0205) (referred to after this as the MCAI), to correct an 
unsafe condition on all Airbus SAS Model A310-203, -204, -221, -222, -
304, -322, -324, and -325 airplanes. The MCAI states that new or more 
restrictive airworthiness limitation tasks related to nose and center 
fuselage and engine mount maintenance are necessary. The MCAI also 
states that not accomplishing the tasks could result in fatigue 
cracking, damage, or corrosion in principal structural elements.
    EASA AD 2021-0205 specifies that it requires tasks (limitations) 
already in Airbus A310 Airworthiness Limitations

[[Page 57140]]

Section (ALS), Part 2, Damage Tolerant Airworthiness Limitation Items 
(DT-ALI), Revision 03, dated December 14, 2018, that is required by 
EASA AD 2019-0091 (which corresponds to FAA AD 2019-20-06, Amendment 
39-19759 (84 FR 55859, October 18, 2019) (AD 2019-20-06)), and that 
incorporation of EASA AD 2021-0205 invalidates (terminates) prior 
instructions for those tasks. This AD therefore terminates the 
limitations for the corresponding tasks, as required by paragraph (g) 
of AD 2019-20-06.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2022-1156.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed EASA AD 2021-0205. This service information 
specifies new or more restrictive airworthiness tasks for airplane 
structures (nose and center fuselage, and engine mount). This material 
is reasonably available because the interested parties have access to 
it through their normal course of business or by the means identified 
in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
described above. The FAA is issuing this AD after determining that the 
unsafe condition described previously is likely to exist or develop on 
other products of the same type design.

AD Requirements

    This AD requires revising the existing maintenance or inspection 
program, as applicable, to incorporate new or more restrictive 
airworthiness tasks, which are specified in EASA AD 2021-0205 described 
previously, as incorporated by reference. Any differences with EASA AD 
2021-0205 are identified as exceptions in the regulatory text of this 
AD.
    This AD requires revisions to certain operator maintenance 
documents to include new actions (e.g., inspections). Compliance with 
these actions is required by 14 CFR 91.403(c). For airplanes that have 
been previously modified, altered, or repaired in the areas addressed 
by this AD, the operator may not be able to accomplish the actions 
described in the revisions. In this situation, to comply with 14 CFR 
91.403(c), the operator must request approval for an alternative method 
of compliance (AMOC) according to paragraph (k)(1) of this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, 
EASA AD 2021-0205 is incorporated by reference in this AD. This AD 
requires compliance with EASA AD 2021-0205 through that incorporation, 
except for any differences identified as exceptions in the regulatory 
text of this AD. Using common terms that are the same as the heading of 
a particular section in EASA AD 2021-0205 does not mean that operators 
need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2021-
0205. Service information required by EASA AD 2021-0205 for compliance 
will be available at regulations.gov by searching for and locating 
Docket No. FAA-2022-1156 after this final rule is published.

Airworthiness Limitation ADs Using the New Process

    The FAA's process of incorporating by reference MCAI ADs as the 
primary source of information for compliance with corresponding FAA ADs 
has been limited to certain MCAI ADs (primarily those with service 
bulletins as the primary source of information for accomplishing the 
actions required by the FAA AD). However, the FAA is now expanding the 
process to include MCAI ADs that require a change to airworthiness 
limitation documents, such as airworthiness limitation sections.
    For these ADs that incorporate by reference an MCAI AD that changes 
airworthiness limitations, the FAA requirements are unchanged. 
Operators must revise the existing maintenance or inspection program, 
as applicable, to incorporate the information specified in the new 
airworthiness limitation document. The airworthiness limitations must 
be followed according to 14 CFR 91.403(c) and 91.409(e).
    The previous format of the airworthiness limitation ADs included a 
paragraph that specified that no alternative actions (e.g., 
inspections) or intervals may be used unless the actions and intervals 
are approved as an AMOC in accordance with the procedures specified in 
the AMOCs paragraph under ``Additional AD Provisions.'' This new format 
includes a ``New Provisions for Alternative Actions and Intervals'' 
paragraph that does not specifically refer to AMOCs, but operators may 
still request an AMOC to use an alternative action or interval.

Justification for Immediate Adoption and Determination of the Effective 
Date

    Section 553(b)(3)(B) of the Administrative Procedure Act (APA) (5 
U.S.C. 551 et seq.) authorizes agencies to dispense with notice and 
comment procedures for rules when the agency, for ``good cause,'' finds 
that those procedures are ``impracticable, unnecessary, or contrary to 
the public interest.'' Under this section, an agency, upon finding good 
cause, may issue a final rule without providing notice and seeking 
comment prior to issuance. Further, section 553(d) of the APA 
authorizes agencies to make rules effective in less than thirty days, 
upon a finding of good cause.
    There are currently no domestic operators of these products. 
Accordingly, notice and opportunity for prior public comment are 
unnecessary, pursuant to 5 U.S.C. 553(b)(3)(B). In addition, for the 
foregoing reason(s), the FAA finds that good cause exists pursuant to 5 
U.S.C. 553(d) for making this amendment effective in less than 30 days.

Regulatory Flexibility Act

    The requirements of the Regulatory Flexibility Act (RFA) do not 
apply when an agency finds good cause pursuant to 5 U.S.C. 553 to adopt 
a rule without prior notice and comment. Because the FAA has determined 
that it has good cause to adopt this rule without notice and comment, 
RFA analysis is not required.

Costs of Compliance

    Currently, there are no affected U.S.-registered airplanes. For any 
affected airplane that may be imported and placed on the U.S. Register 
in the future, the FAA provides the following cost estimates to comply 
with this AD:
    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although the agency recognizes that this number may vary from operator 
to operator. Since operators incorporate maintenance or inspection 
program changes for their affected fleet(s), the FAA has

[[Page 57141]]

determined that a per-operator estimate is more accurate than a per-
airplane estimate.
    The FAA estimates the total cost per operator for the new actions 
to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national Government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866, and
    (2) Will not affect intrastate aviation in Alaska.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2022-19-06 Airbus SAS: Amendment 39-22175; Docket No. FAA-2022-1156; 
Project Identifier MCAI-2021-01024-T.

(a) Effective Date

    This airworthiness directive (AD) is effective October 4, 2022.

(b) Affected ADs

    This AD affects AD 2019-20-06, Amendment 39-19759 (84 FR 55859, 
October 18, 2019) (AD 2019-20-06).

(c) Applicability

    This AD applies to all Airbus SAS Model A310-203, -204, -221, -
222, -304, -322, -324, and -325 airplanes, certificated in any 
category.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Unsafe Condition

    This AD was prompted by a determination that new or more 
restrictive airworthiness tasks are necessary. The FAA is issuing 
this AD to address fatigue cracking, damage, or corrosion in 
principal structural elements. The unsafe condition, if not 
addressed, could result in reduced structural integrity of the 
fuselage.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Revision of the Existing Maintenance or Inspection Program

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) AD 
2021-0205, dated September 14, 2021 (EASA AD 2021-0205).

(h) Exceptions to EASA AD 2021-0205

    (1) The requirements specified in paragraphs (1) and (2) of EASA 
AD 2021-0205 do not apply to this AD.
    (2) Paragraph (3) of EASA AD 2021-0205 specifies revising ``the 
approved AMP'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, within 90 days after the effective date of this AD.
    (3) The initial compliance time for doing the tasks specified in 
paragraph (3) of EASA 2021-0205 is at the applicable ``associated 
thresholds'' as incorporated by the requirements of paragraph (3) of 
EASA AD 2021-0205, or within 90 days after the effective date of 
this AD, whichever occurs later.
    (4) The provisions specified in paragraph (4) of EASA AD 2021-
0205 do not apply to this AD.
    (5) The ``Remarks'' section of EASA AD 2021-0205 does not apply 
to this AD.

(i) New Provisions for Alternative Actions and Intervals

    After the existing maintenance or inspection program has been 
revised as required by paragraph (g) of this AD, no alternative 
actions (e.g., inspections) and intervals are allowed unless they 
are approved as specified in the provisions of the ``Ref. 
Publications'' section of EASA AD 2021-0205.

(j) Terminating Action for AD 2019-20-06

    Accomplishing the actions required by this AD terminates the 
corresponding requirements of AD 2019-20-06, for the tasks 
identified in the service information referenced in EASA AD 2021-
0205 only.

(k) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the International 
Validation Branch, send it to the attention of the person identified 
in paragraph (l) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.

(l) Additional Information

    For more information about this AD, contact Dan Rodina, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
206-231-3225; email [email protected].

(m) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2021-0205, 
dated September 14, 2021.
    (ii) [Reserved]
    (3) For EASA AD 2021-0205, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; website easa.europa.eu. You may find this EASA 
AD on the EASA website at ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational

[[Page 57142]]

Safety Branch, 2200 South 216th St., Des Moines, WA. For information 
on the availability of this material at the FAA, call 206-231-3195.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on September 2, 2022.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2022-20146 Filed 9-16-22; 8:45 am]
BILLING CODE 4910-13-P


