[Federal Register Volume 87, Number 72 (Thursday, April 14, 2022)]
[Proposed Rules]
[Pages 22156-22158]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-07857]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-0457; Project Identifier MCAI-2022-00263-T]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus SAS Model A318 series airplanes, Model A319-111, -
112, -113, -114, -115, -131, -132, and -133 airplanes; Model A320-211, 
-212, -214, -216, -231, -232, and -233 airplanes; and Model A321-111, -
112, -131, -211, -212, -213, -231, and -232 airplanes. This proposed AD 
was prompted by a report that cracks were found on the web horizontal 
flange and inner cap on frame (FR) 68, left-hand (LH) and right-hand 
(RH) side, at stringer (STGR) 22. This proposed AD would require 
repetitive high frequency eddy current (HFEC) inspections for cracks on 
the web horizontal flange and inner cap on FR 68, LH and RH side at 
STGR 22, and applicable corrective actions, as specified in a European 
Union Aviation Safety Agency (EASA) AD, which is proposed for 
incorporation by reference. The FAA is proposing this AD to address the 
unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by May 31, 
2022.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For material that will be incorporated by reference (IBR) in this 
AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 8999 000; email [email protected]; internet 
www.easa.europa.eu. You may find this material on the EASA website at 
https://ad.easa.europa.eu. You may view this material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195. It is also available in the AD 
docket at https://www.regulations.gov by searching for and locating 
Docket No. FAA-2022-0457.

Examining the AD Docket

    You may examine the AD docket at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2022-0457; or in person at 
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, 
except Federal holidays. The AD docket contains this NPRM, the 
mandatory continuing airworthiness information (MCAI), any comments 
received, and other information. The street address for Docket 
Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, Large 
Aircraft Section, International Validation Branch, FAA, 2200 South 
216th Street, Des Moines, WA 98198; telephone and fax 206-231-3225; 
email [email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2022-0457; Project Identifier 
MCAI-2022-00263-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
should be sent to Dan Rodina, Aerospace Engineer, Large Aircraft 
Section, International Validation Branch, FAA, 2200 South 216th Street, 
Des Moines, WA 98198; telephone and fax 206-231-3225; email 
[email protected]. Any commentary that the FAA receives which is not 
specifically designated as CBI will be placed in the public docket for 
this rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2022-0030, dated February 25, 2022 
(EASA AD 2022-0030) (also referred to as the MCAI), to correct an 
unsafe condition for certain Airbus SAS Model A318-111, A318-112, A318-
121, A318-122, A319-111, A319-112, A319-113, A319-114, A319-115, A319-
131, A319-132, A319-133, A320-211, A320-212, A320-214, A320-215, A320-
216, A320-231, A320-232, A320-233, A321-111, A321-112, A321-131, A321-
211, A321-212, A321-213, A321-231 and A321-232 airplanes.
    Model A320-215 airplanes are not certificated by the FAA and are 
not included on the U.S. type certificate data sheet; this proposed AD 
therefore does not include those airplanes in the applicability.
    This proposed AD was prompted by a report that during the 
inspection for the door stop fitting holes at FR 66 and FR 68 required 
by EASA AD 2016-0238, dated December 2, 2016; corrected January 4, 2017 
(which corresponds to FAA AD 2018-03-12, Amendment 39-19185 (83 FR 
5906, February 12, 2018), cracks were found on web horizontal flange 
and inner cap on FR 68, LH and

[[Page 22157]]

RH sides, at STGR 22. The FAA is proposing this AD to address the 
cracks on web horizontal flange and inner cap on FR 68, LH and RH 
sides, at STGR 22, which could result in reduced structural integrity 
of the fuselage. See the MCAI for additional background information.

Related Service Information Under 1 CFR Part 51

    EASA AD 2022-0030 specifies procedures for repetitive HFEC 
inspections for cracks at the web horizontal flange and inner cap on FR 
68, LH and RH sides, at STGR 22, and applicable corrective actions 
(e.g., repairs). This material is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    These products have been approved by the aviation authority of 
another country and are approved for operation in the United States. 
Pursuant to the FAA's bilateral agreement with the State of Design 
Authority, it has notified the FAA of the unsafe condition described in 
the MCAI referenced above. The FAA is issuing this NPRM after 
determining that the unsafe condition described previously is likely to 
exist or develop in other products of these same type designs.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2022-0030 described previously, except for any differences 
identified as exceptions in the regulatory text of this proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to incorporate EASA AD 2022-0030 by reference in the FAA 
final rule. This proposed AD would, therefore, require compliance with 
EASA AD 2022-0030 in its entirety through that incorporation, except 
for any differences identified as exceptions in the regulatory text of 
this proposed AD. Using common terms that are the same as the heading 
of a particular section in EASA AD 2022-0030 does not mean that 
operators need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2022-
0030. Service information required by EASA AD 2022-0030 for compliance 
will be available at https://www.regulations.gov by searching for and 
locating Docket No. FAA-2022-0457 after the FAA final rule is 
published.

Costs of Compliance

    The FAA estimates that this proposed AD would affect 1,585 
airplanes of U.S. registry. The FAA estimates the following costs to 
comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
28 work-hours x $85 per hour = $2,380........................              $0           $2,380       $3,772,300
----------------------------------------------------------------------------------------------------------------

    The FAA has received no definitive data on which to base the cost 
estimates for the on-condition actions specified in this proposed AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Airbus SAS: Docket No. FAA-2022-0457; Project Identifier MCAI-2022-
00263-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by May 31, 2022.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS airplanes specified in paragraphs 
(c)(1) through (4) of

[[Page 22158]]

this AD, certificated in any category, as identified in European 
Union Aviation Safety Agency (EASA) AD 2022-0030, dated February 25, 
2022 (EASA AD 2022-0030).
    (1) Model A318-111, -112, -121, and -122 airplanes.
    (2) Model A319-111, -112, -113, -114, -115, -131, -132, and -133 
airplanes.
    (3) Model A320-211, -212, -214, -216, -231, -232, and -233 
airplanes.
    (4) Model A321-111, -112, -131, -211, -212, -213, -231, and -232 
airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 53, fuselage.

(e) Unsafe Condition

    This AD was prompted by a report that cracks were found on web 
horizontal flange and inner cap on frame (FR) 68, left-hand (LH) and 
right-hand (RH) sides, at stringer (STGR) 22. The FAA is issuing 
this AD to address the cracks on web horizontal flange and inner cap 
on FR 68, LH and RH sides, at STGR 22, which could result in reduced 
structural integrity of the fuselage.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2022-0030.

(h) Exceptions to EASA AD 2022-0030

    (1) Where EASA AD 2022-0030 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2022-0030 does not apply 
to this AD.
    (3) Where paragraph (2) of EASA AD 2022-0030 specifies 
``Accomplishment on an aeroplane of (repetitive) maintenance 
instructions, issued and approved by Airbus,'' for this AD, those 
instructions must have been approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; Airbus SAS's 
EASA Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.
    (4) Where paragraph (3) of EASA AD 2022-0030 specifies if 
``discrepancies and/or cracks are detected, before next flight, 
contact Airbus for approved corrective action(s) instructions and, 
within the compliance time specified therein, accomplish those 
instructions accordingly,'' for this AD, if cracks are detected, the 
cracks must be repaired before further flight using a method 
approved by the Manager, Large Aircraft Section, International 
Validation Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If 
approved by the DOA, the approval must include the DOA-authorized 
signature.
    (5) Where paragraph (4) of EASA AD 2022-0030 specifies ``the 
instructions provided by Airbus,'' for this AD, those instructions 
must be approved by the Manager, Large Aircraft Section, 
International Validation Branch, FAA; or EASA; Airbus SAS's EASA 
DOA. If approved by the DOA, the approval must include the DOA-
authorized signature.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch of the 
certification office, send it to the attention of the person 
identified in paragraph (j)(2) of this AD. Information may be 
emailed to: [email protected]. Before using any approved 
AMOC, notify your appropriate principal inspector, or lacking a 
principal inspector, the manager of the responsible Flight Standards 
Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; Airbus SAS's 
EASA Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (i)(2) of this AD, if any service information contains 
procedures or tests that are identified as RC, those procedures and 
tests must be done to comply with this AD; any procedures or tests 
that are not identified as RC are recommended. Those procedures and 
tests that are not identified as RC may be deviated from using 
accepted methods in accordance with the operator's maintenance or 
inspection program without obtaining approval of an AMOC, provided 
the procedures and tests identified as RC can be done and the 
airplane can be put back in an airworthy condition. Any 
substitutions or changes to procedures or tests identified as RC 
require approval of an AMOC.

(j) Related Information

    (1) For EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 8999 000; email [email protected]; internet 
www.easa.europa.eu. You may find this EASA AD on the EASA website at 
https://ad.easa.europa.eu. You may view this material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195. This material may be 
found in the AD docket at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2022-0457.
    (2) For more information about this AD, contact Dan Rodina, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th Street, Des Moines, WA 98198; 
telephone and fax 206-231-3225; email [email protected].

    Issued on April 7, 2022.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2022-07857 Filed 4-13-22; 8:45 am]
BILLING CODE 4910-13-P


