[Federal Register Volume 86, Number 240 (Friday, December 17, 2021)]
[Proposed Rules]
[Pages 71589-71592]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-27289]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-1067; Project Identifier MCAI-2021-00857-T]
RIN 2120-AA64


Airworthiness Directives; Airbus Canada Limited Partnership (Type 
Certificate Previously Held by C Series Aircraft Limited Partnership 
(CSALP); Bombardier, Inc.) Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-
500-1A11 airplanes. This proposed AD was prompted by a report that some 
tie-rod assemblies may have been over-tightened during the installation 
of interior monuments (such as galleys, lavatories, and forward stowage 
or wardrobes). This proposed AD would require adjusting the tie-rod 
assemblies, as specified in a Transport Canada Civil Aviation (TCCA) 
AD, which is proposed for incorporation by reference. The FAA is 
proposing this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by January 31, 
2022.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For TCCA material that will be incorporated by reference (IBR) in 
this AD, contact TCCA, Transport Canada National Aircraft 
Certification, 159 Cleopatra Drive, Nepean, Ontario K1A 0N5, Canada; 
telephone 888-663-3639; email [email protected]; internet https://tc.canada.ca/en/aviation. You may view this material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des

[[Page 71590]]

Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available in the AD docket at 
https://www.regulations.gov by searching for and locating Docket No. 
FAA-2021-1067.

Examining the AD Docket

    You may examine the AD docket at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-1067; or in person at 
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, 
except Federal holidays. The AD docket contains this NPRM, the 
mandatory continuing airworthiness information (MCAI), any comments 
received, and other information. The street address for Docket 
Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Antariksh Shetty, Aerospace Engineer, 
Airframe and Propulsion Section, FAA, New York ACO Branch, 1600 Stewart 
Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; email [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2021-1067; Project Identifier 
MCAI-2021-00857-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Antariksh Shetty, Aerospace Engineer, Airframe and Propulsion Section, 
FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone 516-228-7300; email [email protected]. Any 
commentary that the FAA receives which is not specifically designated 
as CBI will be placed in the public docket for this rulemaking.

Background

    The TCCA, which is the aviation authority for Canada, has issued 
TCCA AD CF-2021-25, dated July 22, 2021 (TCCA AD CF-2021-25) (also 
referred to as the MCAI), to correct an unsafe condition for certain 
Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500-1A11 
airplanes.
    This proposed AD was prompted by a report that some tie-rod 
assemblies may have been over-tightened during the installation of 
interior monuments (such as galleys, lavatories, and forward stowage or 
wardrobes). The FAA is proposing this AD to address over-tightened 
(pre-loaded) tie-rods that induce unwanted stress in a monument and may 
cause the monument to become unconstrained in an emergency landing, 
potentially blocking exits or injuring occupants. See the MCAI for 
additional background information.

Related Service Information Under 1 CFR Part 51

    TCCA AD CF-2021-25 specifies procedures for, among other actions, 
adjustment of the affected tie-rod assemblies to remove any pre-load. 
This material is reasonably available because the interested parties 
have access to it through their normal course of business or by the 
means identified in the ADDRESSES section.

FAA's Determination

    These products have been approved by the aviation authority of 
another country and are approved for operation in the United States. 
Pursuant to the FAA's bilateral agreement with the State of Design 
Authority, it has notified the FAA of the unsafe condition described in 
the MCAI referenced above. The FAA is issuing this NPRM after 
determining that the unsafe condition described previously is likely to 
exist or develop in other products of these same type designs.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in TCCA AD CF-2021-25 described previously, except for any differences 
identified as exceptions in the regulatory text of this proposed AD and 
except as discussed under ``Difference Between this Proposed AD and the 
MCAI.''

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to incorporate TCCA AD CF-2021-25 by reference in the FAA 
final rule. This proposed AD would, therefore, require compliance with 
TCCA AD CF-2021-25 in its entirety through that incorporation, except 
for any differences identified as exceptions in the regulatory text of 
this proposed AD. Service information required by TCCA AD CF-2021-25 
for compliance will be available at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-1067 after the FAA final 
rule is published.

Difference Between This Proposed AD and the MCAI

    TCCA AD CF-2021-25 specifies an inspection of the tie-rod for pre-
load. The service information required by TCCA AD CF-2021-25 specifies 
that it ``gives the procedure to inspect and release the load the tie-
rod assemblies,'' but does not include any specific inspection 
procedures. This proposed AD does not propose to include any 
inspection.

Costs of Compliance

    The FAA estimates that this proposed AD would affect 21 airplanes 
of U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:

[[Page 71591]]



                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
                 Labor cost                               Parts cost                  product        operators
----------------------------------------------------------------------------------------------------------------
5 work-hours x $85 per hour = $425..........  None..............................            $425          $8,925
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Airbus Canada Limited Partnership (Type Certificate Previously Held 
by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.): 
Docket No. FAA-2021-1067; Project Identifier MCAI-2021-00857-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by January 31, 2022.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus Canada Limited Partnership (Type 
Certificate Previously Held by C Series Aircraft Limited Partnership 
(CSALP); Bombardier, Inc.) Model BD-500-1A10 and BD-500-1A11 
airplanes, certificated in any category, as identified in Transport 
Canada Civil Aviation (TCCA) AD CF-2021-25, dated July 22, 2021 
(TCCA AD CF-2021-25).

(d) Subject

    Air Transport Association (ATA) of America Code 25, Equipment/
Furnishings.

(e) Unsafe Condition

    This AD was prompted by a report that some tie-rod assemblies 
may have been over-tightened during the installation of interior 
monuments (such as those for the galleys, lavatories, and forward 
stowage or wardrobes). The FAA is issuing this AD to address over-
tightened (pre-loaded) tie-rods that induce unwanted stress in the 
monument and may cause the monument to become unconstrained in an 
emergency landing, potentially blocking exits or injuring occupants.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, TCCA AD CF-2021-25.

(h) Exceptions to TCCA AD CF-2021-25

    (1) Where TCCA AD CF-2021-25 refers to hours air time, this AD 
requires using flight hours.
    (2) Where TCCA AD CF-2021-25 refers to its effective date, this 
AD requires using the effective date of this AD.
    (3) The inspection specified in the Corrective Actions paragraph 
of TCCA AD CF-2021-25 does not apply to this AD.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York ACO Branch, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or responsible Flight Standards Office, as appropriate. If 
sending information directly to the manager of the certification 
office, send it to ATTN: Program Manager, Continuing Operational 
Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before 
using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, New York ACO 
Branch, FAA; or TCCA; or Airbus Canada Limited Partnership's TCCA 
Design Approval Organization (DAO). If approved by the DAO, the 
approval must include the DAO-authorized signature.

(j) Related Information

    (1) For TCCA AD CF-2021-25, contact TCCA, Transport Canada 
National Aircraft Certification, 159 Cleopatra Drive, Nepean, 
Ontario K1A 0N5, Canada; telephone 888-663-3639; email [email protected]; internet https://tc.canada.ca/en/aviation. You may view 
this material at the FAA, Airworthiness Products Section, 
Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 
206-231-3195. This material may be found in the AD docket at https://www.regulations.gov by searching for and locating Docket No. FAA-
2021-1067.
    (2) For more information about this AD, contact Antariksh 
Shetty, Aerospace Engineer, Airframe and Propulsion Section, FAA, 
New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone 516-228-7300; email [email protected].


[[Page 71592]]


    Issued on December 6, 2021.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2021-27289 Filed 12-16-21; 8:45 am]
BILLING CODE 4910-13-P


