[Federal Register Volume 86, Number 223 (Tuesday, November 23, 2021)]
[Proposed Rules]
[Pages 66471-66474]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-25464]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-1013; Project Identifier MCAI-2020-01530-T]
RIN 2120-AA64


Airworthiness Directives; BAE Systems (Operations) Limited 
Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to supersede Airworthiness Directive (AD) 
2017-12-08, which applies to all BAE Systems (Operations) Limited Model 
BAe 146-100A, -200A, and -300A airplanes; and Model Avro 146-RJ70A, 
146-RJ85A, and 146-RJ100A airplanes. AD 2017-12-08 requires revising 
the maintenance or inspection program, as applicable, to incorporate 
new or revised structural inspection requirements. Since the FAA issued 
AD 2017-12-08, the FAA has determined that new or more restrictive 
airworthiness limitations are necessary. This proposed AD would require 
revising the existing maintenance or inspection program, as applicable, 
to incorporate new or more restrictive airworthiness limitations. The 
FAA is proposing this AD to address the unsafe condition on these 
products.

DATES: The FAA must receive comments on this proposed AD by January 7, 
2022.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact BAE 
Systems (Operations) Limited, Customer Information Department, 
Prestwick International Airport, Ayrshire, KA9 2RW, Scotland, United 
Kingdom; telephone +44 1292 675207; fax +44 1292 675704; email 
[email protected]; internet http://www.baesystems.com/Businesses/RegionalAircraft/index.htm. You may view this service 
information at the FAA, Airworthiness Products Section, Operational 
Safety Branch, 2200 South 216th St., Des Moines, WA. For information on 
the availability of this material at the FAA, call 206-231-3195.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
1013; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, any comments received, and other information. The street 
address for Docket Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aerospace Engineer, 
Large Aircraft Section, International Validation Branch, FAA, 2200 
South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3228; 
email [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2021-1013; Project Identifier 
MCAI-2020-01530-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
the proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this proposed AD.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated

[[Page 66472]]

as private, that you actually treat as private, and that is relevant or 
responsive to this NPRM, it is important that you clearly designate the 
submitted comments as CBI. Please mark each page of your submission 
containing CBI as ``PROPIN.'' The FAA will treat such marked 
submissions as confidential under the FOIA, and they will not be placed 
in the public docket of this NPRM. Submissions containing CBI should be 
sent to Todd Thompson, Aerospace Engineer, Large Aircraft Section, 
International Validation Branch, FAA, 2200 South 216th St., Des Moines, 
WA 98198; telephone and fax 206-231-3228; email [email protected]. 
Any commentary that the FAA receives which is not specifically 
designated as CBI will be placed in the public docket for this 
rulemaking.

Background

    The FAA issued AD 2017-12-08, Amendment 39-18923 (82 FR 27414, June 
15, 2017) (AD 2017-12-08), for all BAE Systems (Operations) Limited 
Model BAe 146-100A, -200A, and -300A airplanes; and Model Avro 146-
RJ70A, 146-RJ85A, and 146-RJ100A airplanes. AD 2017-12-08 requires 
revising the maintenance or inspection program, as applicable, to 
incorporate new or revised structural inspection requirements. AD 2017-
12-08 resulted from a determination that new or revised structural 
inspection requirements are necessary. The FAA issued AD 2017-12-08 to 
address fatigue cracking of certain structural elements, which could 
adversely affect the structural integrity of the airplane.

Actions Since AD 2017-12-08 Was Issued

    Since the FAA issued AD 2017-12-08, the FAA has determined that new 
or more restrictive airworthiness limitations are necessary.
    The Civil Aviation Authority (CAA), which is the aviation authority 
for the United Kingdom, has issued CAA AD G-2021-0011, dated October 8, 
2021 (CAA AD G-2021-0011) (also referred to after this as the Mandatory 
Continuing Airworthiness Information, or the MCAI), to correct an 
unsafe condition for all BAe 146 and AVRO 146-RJ airplanes. You may 
examine the MCAI in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
1013.
    This proposed AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
proposing this AD to address fatigue cracking of certain structural 
elements, which could adversely affect the structural integrity of the 
airplane. See the MCAI for additional background information.

Related Service Information Under 1 CFR Part 51

    BAE Systems has issued Chapter 05 of BAe 146 Series/AVRO 146-RJ 
Series Aircraft Maintenance Manual, Revision 132, dated August 18, 
2021. This service information describes airworthiness limitations, 
including life limits, maintenance tasks, and CDCCLs.
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
and service information referenced above. The FAA is proposing this AD 
because the FAA evaluated all the relevant information and determined 
the unsafe condition described previously is likely to exist or develop 
on other products of the same type design.

Proposed Requirements of This NPRM

    This proposed AD would retain certain requirements of AD 2017-12-
08. This proposed AD would require revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations.
    This proposed AD would require revisions to certain operator 
maintenance documents to include new actions (e.g., inspections). 
Compliance with these actions is required by 14 CFR 91.403(c). For 
airplanes that have been previously modified, altered, or repaired in 
the areas addressed by this proposed AD, the operator may not be able 
to accomplish the actions described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must request 
approval for an alternative method of compliance according to paragraph 
(k)(1) of this proposed AD.

Costs of Compliance

    The FAA estimates that this proposed AD affects 30 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:
    The FAA estimates the total cost per operator for the retained 
actions from AD 2017-12-08 to be $7,650 (90 work-hours x $85 per work-
hour).
    The FAA has determined that revising the maintenance or inspection 
program takes an average of 90 work-hours per operator, although the 
agency recognizes that this number may vary from operator to operator. 
Since operators incorporate maintenance or inspection program changes 
for their affected fleet(s), the FAA has determined that a per-operator 
estimate is more accurate than a per-airplane estimate. Therefore, the 
agency estimates the average total cost per operator to be $7,650 (90 
work-hours x $85 per work-hour).
    The FAA estimates the total cost per operator for the new proposed 
actions to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

[[Page 66473]]

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by:
0
a. Removing Airworthiness Directive (AD) 2017-12-08, Amendment 39-18923 
(82 FR 27414, June 15, 2017); and
0
b. Adding the following new AD:

BAE Systems (Operations) Limited: Docket No. FAA-2021-1013; Project 
Identifier MCAI-2020-01530-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by January 7, 2022.

(b) Affected ADs

    This AD replaces AD 2017-12-08, Amendment 39-18923 (82 FR 27414, 
June 15, 2017) (AD 2017-12-08).

(c) Applicability

    This AD applies to all BAE Systems (Operations) Limited 
airplanes, certificated in any category, identified in paragraphs 
(c)(1) and (2) of this AD.
    (1) Model BAe 146-100A, -200A, and -300A airplanes.
    (2) Model Avro 146-RJ70A, 146-RJ85A, and 146-RJ100A airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Reason

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
issuing this AD to address fatigue cracking of certain structural 
elements, which could adversely affect the structural integrity of 
the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Retained Revision to the Maintenance or Inspection Program, With No 
Changes

    This paragraph restates the requirements of paragraph (i) of AD 
2017-12-08, with no changes. Within 90 days after July 20, 2017 (the 
effective date of AD 2017-12-08): Revise the maintenance or 
inspection program, as applicable, to incorporate new and revised 
limitations, tasks, thresholds, and intervals using a method 
approved by the Manager, Large Aircraft Section, International 
Validation Branch, FAA.

    Note 1 to paragraph (g): An additional source of guidance for 
the actions specified in paragraph (g) of this AD can be found in 
BAe 146/AVRO 146-RJ Airplane Maintenance Manual, Revision 112, dated 
October 15, 2013.
    Note 2 to paragraph (g): An additional source of guidance for 
the actions specified in paragraph (g) of this AD can be found in 
Corrosion Prevention Control Program (CPCP) Document No. CPCP-146-
01, Revision 4, dated September 15, 2010.
    Note 3 to paragraph (g): An additional source of guidance for 
the actions specified in paragraph (g) of this AD can be found in 
Supplemental Structural Inspections Document (SSID) Document No. 
SSID-146-01, Revision 2, dated August 15, 2012.
    Note 4 to paragraph (g): An additional source of guidance for 
the actions specified in paragraph (g) of this AD can be found in 
Maintenance Review Board Report Document No. MRB 146-01, Issue 2, 
Revision 19, dated August 2012.
    Note 5 to paragraph (g): An additional source of guidance for 
the actions specified in paragraph (g) of this AD can be found in 
BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-
237, Revision 1, dated April 2, 2013.

(h) Retained No Alternative Actions, Intervals, and/or Critical Design 
Configuration Control Limitations (CDCCLs), With No Changes

    This paragraph restates the requirements of paragraph (j) of AD 
2017-12-08, with no changes. Except as specified in paragraph (i) of 
this AD: After accomplishing the revision required by paragraph (g) 
of this AD, no alternative actions (e.g., inspections), intervals, 
and/or CDCCLs may be used, unless the actions, intervals, and/or 
CDCCLs are approved as an alternative method of compliance (AMOC) in 
accordance with the procedures specified in paragraph (k)(1) of this 
AD.

(i) New Maintenance or Inspection Program Revision

    Within 90 days after the effective date of this AD, revise the 
existing maintenance or inspection program, as applicable, to 
incorporate the information specified in Chapter 05 of BAe 146 
Series/AVRO 146-RJ Series Aircraft Maintenance Manual, Revision 132, 
dated August 18, 2021. The initial compliance time for doing the 
tasks is at the time specified in Chapter 05 of BAe 146 Series/AVRO 
146-RJ Series Aircraft Maintenance Manual, Revision 132, dated 
August 18, 2021, or within 90 days after the effective date of this 
AD, whichever occurs later. Accomplishing the revision required by 
this paragraph terminates the actions required by paragraph (g) of 
this AD.

(j) New No Alternative Actions, Intervals, or CDCCLs

    After the existing maintenance or inspection program has been 
revised as required by paragraph (i) of this AD, no alternative 
actions (e.g., inspections), intervals, or CDCCLs may be used unless 
the actions, intervals, and/or CDCCLs are approved as an AMOC in 
accordance with the procedures specified in paragraph (k)(1) of this 
AD.

(k) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (l)(2) of 
this AD. Information may be emailed to: [email protected].
    (i) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the responsible Flight Standards Office.
    (ii) AMOCs approved for AD 2017-12-08 are approved as AMOCs for 
the corresponding provisions of this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or the Civil Aviation 
Authority (CAA); or BAE Systems (Operations) Limited's CAA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.

(l) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) CAA AD G-2021-0011, dated October 8, 2021, for related 
information. This MCAI may be found in the AD docket on the internet 
at https://www.regulations.gov by searching for and locating Docket 
No. FAA-2021-1013.
    (2) For more information about this AD, contact Todd Thompson, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3228; email [email protected].
    (3) For service information identified in this AD, contact BAE 
Systems (Operations) Limited, Customer Information Department, 
Prestwick International Airport, Ayrshire, KA9 2RW, Scotland, United 
Kingdom; telephone +44 1292 675207; fax +44 1292 675704; email 
[email protected]; internet http://www.baesystems.com/Businesses/RegionalAircraft/index.htm. You may view this service 
information at the FAA, Airworthiness Products Section, Operational 
Safety Branch, 2200 South 216th St., Des Moines, WA. For information 
on the availability of this material at the FAA, call 206-231-3195.


[[Page 66474]]


    Issued on November 17, 2021.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2021-25464 Filed 11-22-21; 8:45 am]
BILLING CODE 4910-13-P


