[Federal Register Volume 87, Number 28 (Thursday, February 10, 2022)]
[Rules and Regulations]
[Pages 7705-7708]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-02748]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0886; Project Identifier MCAI-2021-00341-R; 
Amendment 39-21903; AD 2022-02-06]
RIN 2120-AA64


Airworthiness Directives; Airbus Helicopters

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Airbus Helicopters Model EC120B helicopters. This AD was prompted by a 
report of geometrical non-conformities in the tail rotor blade (TRB) 
root section discovered during an accident investigation of a Model 
EC130B helicopter. Due to the similarity of design and production 
requirements, certain TRBs for the Model EC120B helicopters were 
inspected and

[[Page 7706]]

geometrical non-conformities were also found. This AD requires an 
inspection (dimensional check) to verify conformity, and replacement of 
certain TRBs if necessary, as specified in a European Union Aviation 
Safety Agency (EASA) AD, which is incorporated by reference. The FAA is 
issuing this AD to address the unsafe condition on these products.

DATES: This AD is effective March 17, 2022.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of March 17, 
2022.

ADDRESSES: For EASA material incorporated by reference (IBR) in this 
AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
phone: +49 221 8999 000; email: [email protected]; internet: 
www.easa.europa.eu. You may find the EASA material on the EASA website 
at https://ad.easa.europa.eu. You may view this material at the FAA, 
Office of the Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., 
Room 6N-321, Fort Worth, TX 76177. For information on the availability 
of this material at the FAA, call (817) 222-5110. It is also available 
in the AD docket at https://www.regulations.gov by searching for and 
locating Docket No. FAA-2021-0886.

Examining the AD Docket

    You may examine the AD docket at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0886; or in person at 
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, 
except Federal holidays. The AD docket contains this final rule, the 
EASA AD, any comments received, and other information. The address for 
Docket Operations is U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Andrea Jimenez, Aerospace Engineer, 
COS Program Management Section, Operational Safety Branch, Compliance & 
Airworthiness Division, FAA, 1600 Stewart Ave., Suite 410, Westbury, NY 
11590; phone: (516) 228-7330; email: [email protected].

SUPPLEMENTARY INFORMATION:

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2021-0079, dated March 17, 2021 
(EASA AD 2021-0079), to correct an unsafe condition for all Airbus 
Helicopters Model EC120B helicopters.
    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to all Airbus Helicopters 
Model EC120B helicopters. The NPRM published in the Federal Register on 
October 28, 2021 (86 FR 59653). The NPRM was prompted by a report of 
geometrical non-conformities in the TRB root section discovered during 
an accident investigation of a Model EC130B helicopter. Due to the 
similarity of design and production requirements, certain TRBs for the 
Model EC120B helicopters were inspected and geometrical non-
conformities were also found. The NPRM proposed to require an 
inspection (dimensional check) to verify conformity, and replacement of 
certain TRBs if necessary, as specified in EASA AD 2021-0079.
    The FAA is issuing this AD to detect and correct geometrical non 
conformities of the TRB root section. The unsafe condition, if not 
addressed, could result in crack initiation and TRB failure, and 
possibly result in loss of control of the helicopter. See EASA AD 2021-
0079 for additional background information.

Discussion of Final Airworthiness Directive

Comments

    The FAA received no comments on the NPRM or on the determination of 
the costs.

Conclusion

    These helicopters have been approved by EASA and are approved for 
operation in the United States. Pursuant to the FAA's bilateral 
agreement with the European Union, EASA has notified the FAA about the 
unsafe condition described in its AD. The FAA reviewed the relevant 
data and determined that air safety requires adopting this AD as 
proposed. Accordingly, the FAA is issuing this AD to address the unsafe 
condition on these helicopters. Except for minor editorial changes, 
this AD is adopted as proposed in the NPRM.

Related Service Information Under 1 CFR Part 51

    EASA AD 2021-0079 requires an inspection (dimensional check) to 
verify TRB conformity, and replacement of certain TRBs if necessary. 
EASA AD 2021-0079 also prohibits rework, repair, or modification of 
affected parts in the critical section (affected area of the TRB 
assembly root).
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 89 helicopters of U.S. 
Registry. Labor rates are estimated at $85 per work-hour. Based on 
these numbers, the FAA estimates the following costs to comply with 
this AD.

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
               Action                         Labor cost            Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Inspection..........................  4 work-hours x $85 per                  $0            $340         $30,260
                                       hour = $340.
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary 
replacements that would be required based on the results of the 
required inspection. The agency has no way of determining the number of 
aircraft that might need these replacements:

                                               On-Condition Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                    Action                                 Labor cost               Parts cost        product
----------------------------------------------------------------------------------------------------------------
Blade Replacement.............................  10 work-hours x $85 per hour =            $4,000          $4,850
                                                 $850.
----------------------------------------------------------------------------------------------------------------


[[Page 7707]]

    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some of the costs of this AD 
may be covered under warranty, thereby reducing the cost impact on 
affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2022-02-06 Airbus Helicopters: Amendment 39-21903; Docket No. FAA-
2021-0886; Project Identifier MCAI-2021-00341-R.

(a) Effective Date

    This airworthiness directive (AD) is effective March 17, 2022.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Airbus Helicopters Model EC120B 
helicopters, certificated in any category.

(d) Subject

    Joint Aircraft Service Component (JASC) Code: 6410, Tail Rotor 
Blades.

(e) Unsafe Condition

    This AD was prompted by a report of geometrical non-conformities 
in the tail rotor blade (TRB) root section discovered during an 
accident investigation of a Model EC130B helicopter. Due to the 
similarity of design and production requirements, certain TRBs for 
the Model EC120B helicopters were inspected and geometrical non-
conformities were also found. The FAA is issuing this AD to detect 
and correct geometrical non-conformities of the TRB root section. 
The unsafe condition, if not addressed, could result in crack 
initiation and TRB failure, and possibly result in loss of control 
of the helicopter.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) AD 
2021-0079, dated March 17, 2021 (EASA AD 2021-0079).

(h) Exceptions to EASA AD 2021-0079

    (1) Where EASA AD 2021-0079 requires compliance in terms of 
flight hours, this AD requires using hours time-in-service.
    (2) Where EASA AD 2021-0079 refers to its effective date, this 
AD requires using the effective date of this AD.
    (3) Where the service information referenced in EASA AD 2021-
0079 specifies discarding a part, this AD requires removing that 
part from service.
    (4) This AD does not mandate compliance with the ``Remarks'' 
section of EASA AD 2021-0079.
    (5) Where the service information referenced in EASA AD 2021-
0079 specifies to measure using the Smartphone application, the 
PowerPoint method, or ``Contacting customer support with a specific 
procedure,'' this AD requires determining the specified measurements 
but those methods of measurement are not required by this AD.

(i) No Reporting Requirement

    Although the service information referenced in EASA AD 2021-0079 
specifies to submit certain information to the manufacturer, this AD 
does not include that requirement.

(j) Special Flight Permit

    Special flight permits may be issued in accordance with 14 CFR 
21.197 and 21.199 to operate the helicopter to a location where the 
actions of this AD can be performed, provided no passengers are 
onboard.

(k) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, International Validation Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the manager of the International Validation Branch, send 
it to the attention of the person identified in paragraph (l) of 
this AD. Information may be emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.

(l) Related Information

    For more information about this AD, contact Andrea Jimenez, 
Aerospace Engineer, COS Program Management Section, Operational 
Safety Branch, Compliance & Airworthiness Division, FAA, 1600 
Stewart Ave., Suite 410, Westbury, NY 11590; phone: (516) 228-7330; 
email: [email protected].

(m) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2021-0079, 
dated March 17, 2021.
    (ii) [Reserved]
    (3) For EASA AD 2021-0079, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; phone: +49 221 8999 000; email: 
[email protected]; internet: www.easa.europa.eu. You may find the 
EASA material on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this service information at the FAA, Office of 
the Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 
6N-321, Fort Worth, TX 76177. For information on the availability of 
this material at the FAA, call (817) 222-5110. This material may be 
found in the AD docket

[[Page 7708]]

at https://www.regulations.gov by searching for and locating Docket 
No. FAA-2021-0886.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on January 7, 2022.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2022-02748 Filed 2-9-22; 8:45 am]
BILLING CODE 4910-13-P


