[Federal Register Volume 86, Number 207 (Friday, October 29, 2021)]
[Rules and Regulations]
[Pages 59842-59845]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-23431]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0840; Project Identifier MCAI-2021-00262-T; 
Amendment 39-21760; AD 2021-20-22]
RIN 2120-AA64


Airworthiness Directives; Fokker Services B.V. Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Fokker Services B.V. Model F28 Mark 0070 and Mark 0100 
airplanes. This AD was prompted by a report of exfoliation corrosion 
found during an inspection of the wing front spar lower boom. This AD 
requires an inspection for corrosion of the wing front spar lower boom, 
and applicable corrective actions, as specified in a European Union 
Aviation Safety Agency (EASA) AD, which is incorporated by reference. 
The FAA is issuing this AD to address the unsafe condition on these 
products.

DATES: This AD becomes effective November 15, 2021.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of November 15, 
2021.
    The FAA must receive comments on this AD by December 13, 2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For EASA material incorporated by reference (IBR) in this AD, 
contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone 
+49 221 8999 000; email [email protected]; internet 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at https://ad.easa.europa.eu. You may view this material at the FAA, 
Airworthiness Products Section,

[[Page 59843]]

Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 206-
231-3195. It is also available in the AD docket on the internet at 
https://www.regulations.gov by searching for and locating Docket No. 
FAA-2021-0840.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
0840; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this AD, the mandatory continuing airworthiness information (MCAI), any 
comments received, and other information. The street address for Docket 
Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Ho-Joon Lim, Aerospace Engineer, Large 
Aircraft Section, International Validation Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3405; email 
[email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written data, views, or arguments 
about this final rule. Send your comments to an address listed under 
ADDRESSES. Include ``Docket No. FAA-2021-0840; Project Identifier MCAI-
2021-00262-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the final rule, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this final rule because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this final rule.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this AD contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this AD, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this AD. Submissions containing CBI should be sent to Ho-Joon 
Lim, Aerospace Engineer, Large Aircraft Section, International 
Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; 
telephone and fax 206-231-3405; email [email protected]. Any 
commentary that the FAA receives which is not specifically designated 
as CBI will be placed in the public docket for this rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2021-0059, dated March 2, 2021 (EASA 
AD 2021-0059) (also referred to as the MCAI), to correct an unsafe 
condition for certain Model F28 Mark 0070 and Mark 0100 airplanes.
    This AD was prompted by a report of exfoliation corrosion found 
during an inspection of the wing front spar lower boom. This corrosion 
was found between wing station (WSTA) 3100 and WSTA 3600. It was 
determined that corrosion may also exist at other spanwise positions on 
the wing front spar lower boom. The FAA is issuing this AD to address 
corrosion, which if not corrected, could lead to reduced structural 
integrity of the wing structure and reduced wing ultimate and limit 
load capability. See the MCAI for additional background information.

Related Service Information Under 1 CFR Part 51

    EASA AD 2021-0059 specifies procedures for a detailed inspection 
for corrosion of the wing front spar lower boom between WSTA 1825 and 
WSTA 10110, corrective actions (repair and restoration of the surface 
corrosion), and sending an inspection report to Fokker Services B.V. 
This material is reasonably available because the interested parties 
have access to it through their normal course of business or by the 
means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
described above. The FAA is issuing this AD after determining that the 
unsafe condition exists and is likely to exist or develop on other 
products of the same type design.

Requirements of This AD

    This AD requires accomplishing the actions specified in the MCAI 
described previously, except for any differences identified as 
exceptions in the regulatory text of this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, 
EASA AD 2021-0059 is incorporated by reference in this AD. This AD 
requires compliance with EASA AD 2021-0059 in its entirety through that 
incorporation, except for any differences identified as exceptions in 
the regulatory text of this AD. Using common terms that are the same as 
the heading of a particular section in EASA AD 2021-0059 does not mean 
that operators need comply only with that section. For example, where 
the AD requirement refers to ``all required actions and compliance 
times,'' compliance with this AD requirement is not limited to the 
section titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 
2021-0059. Service information required by EASA AD 2021-0059 for 
compliance will be available at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0840 after this AD is 
published.

Interim Action

    The FAA considers this AD interim action. The inspection reports 
that are required by this AD will enable the manufacturer to re-
evaluate the current 12-year visual inspection interval of the front 
spar front side. Once final action has been identified, the FAA might 
consider further rulemaking.

FAA's Justification and Determination of the Effective Date

    There are currently no domestic operators of these products. 
Accordingly, notice and opportunity for prior public comment are 
unnecessary,

[[Page 59844]]

pursuant to 5 U.S.C. 553(b)(3). In addition, for the foregoing reason, 
the FAA finds that good cause exists pursuant to 5 U.S.C. 553(d) for 
making this amendment effective in less than 30 days.

Regulatory Flexibility Act (RFA)

    There are currently no domestic operators of these products. 
Accordingly, notice and opportunity for prior public comment are 
unnecessary, pursuant to 5 U.S.C. 553(b)(3)(B). In addition, for the 
foregoing reason(s), the FAA finds that good cause exists pursuant to 5 
U.S.C. 553(d) for making this amendment effective in less than 30 days.

Costs of Compliance

    Currently, there are no affected U.S.-registered airplanes. If an 
affected airplane is imported and placed on the U.S. Register in the 
future, the FAA provides the following cost estimates to comply with 
this AD:

                 Estimated Costs for Required Actions *
------------------------------------------------------------------------
                                                             Cost per
              Labor cost                   Parts cost        product
------------------------------------------------------------------------
28 work-hours x $85 per hour = $2,380.              $0           $2,380
------------------------------------------------------------------------
*Table does not include estimated costs for reporting.

    The FAA estimates that it takes about 1 work-hour per product to 
comply with the reporting requirement in this AD. The average labor 
rate is $85 per hour. Based on these figures, the FAA estimates the 
cost of reporting the inspection results on U.S. operators to be $0, or 
$85 per product.
    The FAA has received no definitive data on which to base the cost 
estimates for the on-condition actions specified in this AD.

Paperwork Reduction Act

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to penalty for 
failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act unless that collection of 
information displays a current valid OMB control number. The control 
number for the collection of information required by this AD is 2120-
0056. Public reporting for this collection of information is estimated 
to take approximately 1 hour per response, including time for reviewing 
instructions, searching existing data sources, gathering and 
maintaining the data needed, and completing and reviewing the 
collection of information. All responses to this collection of 
information are mandatory. Send comments regarding this burden estimate 
or any other aspect of this collection of information, including 
suggestions for reducing this burden, to: Information Collection 
Clearance Officer, Federal Aviation Administration, 10101 Hillwood 
Parkway, Fort Worth, TX 76177-1524.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866, and
    (2) Will not affect intrastate aviation in Alaska.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2021-20-22 Fokker Services B.V.: Amendment 39-21760; Docket No. FAA-
2021-0840; Project Identifier MCAI-2021-00262-T.

(a) Effective Date

    This airworthiness directive (AD) becomes effective November 15, 
2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Fokker Services B.V. Model F28 Mark 0070 and 
Mark 0100 airplanes, certificated in any category, as identified in 
European Union Aviation Safety Agency (EASA) AD 2021-0059, dated 
March 2, 2021 (EASA AD 2021-0059).

(d) Subject

    Air Transport Association (ATA) of America Code 57, Wings.

(e) Reason

    This AD was prompted by a report of exfoliation corrosion found 
during an inspection of the wing front spar lower boom. The FAA is 
issuing this AD to address corrosion, which if not corrected, could 
lead to reduced structural integrity of the wing structure and 
reduced wing ultimate and limit load capability.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and

[[Page 59845]]

compliance times specified in, and in accordance with, EASA AD 2021-
0059.

(h) Exceptions to EASA AD 2021-0059

    (1) Where EASA AD 2021-0059 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2021-0059 does not apply 
to this AD.
    (3) Paragraph (3) of EASA AD 2021-0059 specifies to report 
inspection results to Fokker Services B.V. within a certain 
compliance time. For this AD, report inspection results at the 
applicable time specified in paragraph (h)(3)(i) or (ii) of this AD.
    (i) If the inspection was done on or after the effective date of 
this AD: Submit the report within 30 days after the inspection.
    (ii) If the inspection was done before the effective date of 
this AD: Submit the report within 30 days after the effective date 
of this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (j) of this 
AD. Information may be emailed to: [email protected]. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Fokker 
Services B.V.'s EASA Design Organization Approval (DOA). If approved 
by the DOA, the approval must include the DOA-authorized signature.

(j) Related Information

    For more information about this AD, contact Ho-Joon Lim, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3405; email [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2021-0059, 
dated March 2, 2021.
    (ii) [Reserved]
    (3) For EASA AD 2021-0059, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; Internet www.easa.europa.eu. You may find this 
EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195. This material may be found in the AD 
docket on the internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2021-0840.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on September 24, 2021.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2021-23431 Filed 10-28-21; 8:45 am]
BILLING CODE 4910-13-P


