[Federal Register Volume 86, Number 153 (Thursday, August 12, 2021)]
[Proposed Rules]
[Pages 44314-44316]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-16938]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0658; Project Identifier MCAI-2020-01582-T]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc., Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Bombardier, Inc., Model BD-100-1A10 airplanes. This 
proposed AD was prompted by a discovery that a lockwire may not have 
been installed on the side stay actuator pin nut of the main landing 
gear (MLG). This proposed AD would require inspecting the left-hand and 
right-hand MLG side stay actuator assembly pin nut for the presence of 
a lockwire, and installing a lockwire if necessary. The FAA is 
proposing this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by September 
27, 2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact 
Bombardier, Inc., 200 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec 
H4S 2A3, Canada; North America toll-free telephone 1-866-538-1247 or 
direct-dial telephone 1-514-855-2999; email ac.yul@aero.bombardier.com; 
internet https://www.bombardier.com. You may view this service 
information at the FAA, Airworthiness Products Section, Operational 
Safety Branch, 2200 South 216th St., Des Moines, WA. For information on 
the availability of this material at the FAA, call 206-231-3195.

Examining the AD Docket

    You may examine the AD docket at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0658; or in person at 
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, 
except Federal holidays. The AD docket contains this NPRM, any comments 
received, and other information. The street address for Docket 
Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Elizabeth Dowling, Aerospace Engineer, 
Mechanical Systems and Administrative Services Section, FAA, New York 
ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone 516-228-7300; fax 516-794-5531; email 9-avs-nyaco-cos@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2021-0658; Project Identifier 
MCAI-2020-01582-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
the proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Elizabeth Dowling, Aerospace Engineer, Mechanical Systems and 
Administrative Services Section, FAA, New York ACO Branch, 1600 Stewart 
Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; fax 516-
794-5531; email 9-avs-nyaco-cos@faa.gov. Any commentary that the FAA 
receives which is not specifically designated as CBI will be placed in 
the public docket for this rulemaking.

Background

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued TCCA AD CF-2020-52, dated November 30, 
2020 (also referred to after this as the Mandatory

[[Page 44315]]

Continuing Airworthiness Information, or the MCAI), to correct an 
unsafe condition for certain Bombardier, Inc., Model BD-100-1A10 
airplanes. You may examine the MCAI in the AD docket at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
0658.
    This proposed AD was prompted by a discovery that a lockwire may 
not have been installed on the side stay actuator pin nut of the MLG. 
The FAA is proposing this AD to address a possible missing lockwire, 
which could result in loss of the nut, and if undetected, lead to the 
collapse of the affected MLG. See the MCAI for additional background 
information.

Related Service Information Under 1 CFR Part 51

    Bombardier has issued Service Bulletin 100-32-36, dated June 25, 
2020; and Service Bulletin 350-32-012, dated June 25, 2020. This 
service information describes procedures for inspecting the left-hand 
and right-hand MLG side stay actuator assembly pin nut for presence of 
a lockwire and installing a lockwire. These documents are distinct 
since they apply to different airplane configurations.
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
and service information referenced above. The FAA is proposing this AD 
because the FAA evaluated all the relevant information and determined 
the unsafe condition described previously is likely to exist or develop 
on other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in the service information already described.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 623 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
1 work-hour x $85 per hour = $85.............................              $0              $85          $52,955
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary on-
condition actions that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need these on-condition actions:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
                                                             Cost per
              Labor cost                   Parts cost        product
------------------------------------------------------------------------
1 work-hour x $85 per hour = $85......              $1              $86
------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Bombardier, Inc.: Docket No. FAA-2021-0658; Project Identifier MCAI-
2020-01582-T.

[[Page 44316]]

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by September 27, 2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc., Model BD-100-1A10, 
certificated in any category, serial numbers 20003 through 20780 
inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 32, Landing 
gear.

(e) Unsafe Condition

    This AD was prompted by a discovery that a lockwire may not have 
been installed on the side stay actuator pin nut of the main landing 
gear (MLG). The FAA is issuing this AD to address a possible missing 
lockwire, which could result in loss of the nut, and if undetected, 
lead to the collapse of the affected MLG.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Within 12 months after the effective date of this AD: Inspect 
the left-hand (LH) and right-hand (RH) MLG side stay actuator 
assembly pin nuts for presence of a lockwire, in accordance with 
paragraph 2.B of the Accomplishment Instructions of the applicable 
service information specified in paragraphs (g)(1) and (2) of this 
AD. If the lockwire is missing: Before further flight, install a 
lockwire in accordance with paragraph 2.C of the Accomplishment 
Instructions of the applicable service information specified in 
paragraphs (g)(1) and (2) of this AD.
    (1) Bombardier Service Bulletin 100-32-36, dated June 25, 2020.
    (2) Bombardier Service Bulletin 350-32-012, dated June 25, 2020.

(h) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York ACO Branch, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or responsible Flight Standards Office, as appropriate. If 
sending information directly to the manager of the certification 
office, send it to ATTN: Program Manager, Continuing Operational 
Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before 
using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, New York ACO 
Branch, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If 
approved by the DAO, the approval must include the DAO-authorized 
signature.

(i) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI), TCCA AD CF-2020-52, dated November 30, 2020, for related 
information. This MCAI may be found in the AD docket on the internet 
at https://www.regulations.gov by searching for and locating Docket 
No. FAA-2021-0658.
    (2) For more information about this AD, contact Elizabeth 
Dowling, Aerospace Engineer, Mechanical Systems and Administrative 
Services Section, FAA, New York ACO Branch, 1600 Stewart Avenue, 
Suite 410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-
5531; email 9-avs-nyaco-cos@faa.gov.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., 200 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 2A3, Canada; North America toll-free telephone 1-
866-538-1247 or direct-dial telephone 1-514-855-2999; email 
ac.yul@aero.bombardier.com; internet https://www.bombardier.com. You 
may view this service information at the FAA, Airworthiness Products 
Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at 
the FAA, call 206-231-3195.

    Issued on August 4, 2021.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2021-16938 Filed 8-11-21; 8:45 am]
BILLING CODE 4910-13-P


