[Federal Register Volume 86, Number 157 (Wednesday, August 18, 2021)]
[Proposed Rules]
[Pages 46167-46169]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-17362]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0564; Project Identifier AD-2020-01350-T]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for all The Boeing Company Model MD-11 and MD-11F airplanes. This 
proposed AD was prompted by reports indicating incidents of wires 
chafing against the inboard upper corner of the observer station 
circuit breaker panel. This proposed AD would require, depending on 
airplane configuration, doing a general visual inspection of the right 
observer station upper main circuit breaker panel and wiring for 
certain missing parts; doing an inspection of the right observer 
station upper main circuit breaker panel to determine if a certain 
bracket part number is installed; doing a general visual inspection of 
certain wire assemblies for any damage; modifying the observer station 
upper main circuit breaker panel; and applicable on-condition actions. 
The FAA is proposing this AD to address the unsafe condition on these 
products.

DATES: The FAA must receive comments on this proposed AD by October 4, 
2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; internet https://www.myboeingfleet.com. You may 
view this service information at the FAA, Airworthiness Products 
Section, Operational Safety Branch, 2200 South 216th St., Des Moines, 
WA. For information on the availability of this material at the FAA, 
call 206-231-3195. It is also available at https://www.regulations.gov 
by searching for and locating Docket No. FAA-2021-0564.

Examining the AD Docket

    You may examine the AD docket at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0564; or in person at 
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, 
except Federal holidays. The AD docket contains this NPRM, any comments 
received, and other information. The street address for Docket 
Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Eric Igama, Aerospace Engineer, 
Systems and Equipment Section, FAA, Los Angeles ACO Branch, 3960 
Paramount Boulevard, Lakewood, CA 90712-4137; phone: 562-627-5388; fax: 
562-627-5210; email: Roderick.Igama@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2021-0564; Project Identifier 
AD-2020-01350-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
the proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to Eric 
Igama, Aerospace Engineer, Systems and Equipment Section, FAA, Los 
Angeles ACO Branch, 3960 Paramount Boulevard, Lakewood, CA 90712-4137; 
phone: 562-627-5388; fax: 562-627-5210; email: Roderick.Igama@faa.gov. 
Any commentary that the FAA receives which is not specifically 
designated as CBI will be placed in the public docket for this 
rulemaking.

Background

    The FAA has received reports indicating incidents of wires chafing 
against the inboard upper corner of the observer station circuit 
breaker panel. It has been determined that this condition allows for 
the chafed electrical wires to arc against the metal panel during the 
opening and closing of the panel. This condition, if not addressed, 
could result in wire chafing and arcing on the panel,

[[Page 46168]]

which could cause damage to equipment, and result in loss of electrical 
power and a possible in-flight fire.

FAA's Determination

    The FAA is issuing this NPRM after determining that the unsafe 
condition described previously is likely to exist or develop on other 
products of the same type design.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Boeing Alert Service Bulletin MD11-24A204, 
Revision 2, dated April 14, 2021. For certain airplanes, this service 
information describes procedures for doing a general visual inspection 
of the right observer station upper main circuit breaker panel and 
wiring for missing installation of sleeving, grommets, and spacers; 
doing an inspection of the right observer station upper main circuit 
breaker panel to determine if bracket part number SR11240046-11 is 
installed; and applicable on-condition actions. On-condition actions 
include repairing or replacing damaged wires, installing sleeves and 
routing wires, trimming and re-identifying the bracket, and replacing 
any missing grommets or spacers.
    For certain other airplanes, this service information describes 
procedures for doing a general visual inspection of wire assemblies 
ABS9110 and ABS9115 for any damage (i.e., wire chafing, arcing), 
modifying the observer station upper main circuit breaker panel, and 
applicable on-condition actions. On-condition actions include repairing 
or replacing damaged wires.
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in ADDRESSES.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions identified 
as ``RC'' (required for compliance) in the Accomplishment Instructions 
of Boeing Alert Service Bulletin MD11-24A204, Revision 2, dated April 
14, 2021, already described, except for any differences identified as 
exceptions in the regulatory text of this proposed AD. For information 
on the procedures and compliance times, see this service information at 
https://www.regulations.gov by searching for and locating Docket No. 
FAA-2021-0564.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 118 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                 Cost on U.S.
             Action                     Labor cost          Parts cost     Cost per product        operators
----------------------------------------------------------------------------------------------------------------
Inspections....................  Up to 17 work-hours x                $0  Up to $1,445......  Up to $170,510.
                                  $85 per hour = Up to
                                  $1,445.
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary actions 
that would be required based on the results of the proposed inspection. 
The FAA has no way of determining the number of aircraft that might 
need these actions:

                                              On-Condition Costs *
----------------------------------------------------------------------------------------------------------------
               Action                          Labor cost             Parts cost          Cost per product
----------------------------------------------------------------------------------------------------------------
Replacement, installation and         Up to 3 work-hours x $85 per            $428  Up to $683.
 trimming.                             hour = Up to $255.
----------------------------------------------------------------------------------------------------------------
* The FAA has received no definitive data on which to base the cost estimates for the on-condition repairs
  specified in this proposed AD.

    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this proposed AD may be covered under warranty, thereby reducing the 
cost impact on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.

[[Page 46169]]

Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

The Boeing Company: Docket No. FAA-2021-0564; Project Identifier AD-
2020-01350-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by October 4, 2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all The Boeing Company Model MD-11 and MD-11F 
airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 24, Electrical 
power.

(e) Unsafe Condition

    This AD was prompted by reports indicating incidents of wires 
chafing against the inboard upper corner of the observer station 
circuit breaker panel. The FAA is issuing this AD to address wire 
chafing and arcing on the panel, which could cause damage to 
equipment, and result in loss of electrical power and a possible in-
flight fire.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as specified in paragraph (h) of this AD: At the 
applicable times specified in paragraph 1.E., ``Compliance,'' of 
Boeing Alert Service Bulletin MD11-24A204, Revision 2, dated April 
14, 2021, do all applicable actions identified as ``RC'' (required 
for compliance) in, and in accordance with, the Accomplishment 
Instructions of Boeing Alert Service Bulletin MD11-24A204, Revision 
2, dated April 14, 2021.

(h) Exception to Service Information Specifications

    Where Boeing Alert Service Bulletin MD11-24A204, Revision 2, 
dated April 14, 2021, uses the phrase ``the Revision 2 date of this 
service bulletin,'' this AD requires using ``the effective date of 
this AD.''

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Los Angeles ACO Branch, FAA, has the authority 
to approve AMOCs for this AD, if requested using the procedures 
found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your 
request to your principal inspector or responsible Flight Standards 
Office, as appropriate. If sending information directly to the 
manager of the certification office, send it to the attention of the 
person identified in Related Information. Information may be emailed 
to: 9-ANM-LAACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the responsible Flight Standards Office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by The Boeing Company Organization Designation 
Authorization (ODA) that has been authorized by the Manager, Los 
Angeles ACO Branch, FAA, to make those findings. To be approved, the 
repair method, modification deviation, or alteration deviation must 
meet the certification basis of the airplane, and the approval must 
specifically refer to this AD.
    (4) For service information that contains steps that are labeled 
as Required for Compliance (RC), the provisions of paragraphs 
(i)(4)(i) and (ii) of this AD apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. If a step or substep is labeled ``RC Exempt,'' then the 
RC requirement is removed from that step or substep. An AMOC is 
required for any deviations to RC steps, including substeps and 
identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(j) Related Information

    (1) For more information about this AD, contact Eric Igama, 
Aerospace Engineer, Systems and Equipment Section, FAA, Los Angeles 
ACO Branch, 3960 Paramount Boulevard, Lakewood, CA 90712-4137; 
phone: 562-627-5388; fax: 562-627-5210; email: 
Roderick.Igama@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; internet https://www.myboeingfleet.com. You may view this service information at the 
FAA, Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195.

    Issued on July 9, 2021.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2021-17362 Filed 8-17-21; 8:45 am]
BILLING CODE 4910-13-P


