[Federal Register Volume 86, Number 136 (Tuesday, July 20, 2021)]
[Proposed Rules]
[Pages 38239-38242]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-15333]


 ========================================================================
 Proposed Rules
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains notices to the public of 
 the proposed issuance of rules and regulations. The purpose of these 
 notices is to give interested persons an opportunity to participate in 
 the rule making prior to the adoption of the final rules.
 
 ========================================================================
 

  Federal Register / Vol. 86, No. 136 / Tuesday, July 20, 2021 / 
Proposed Rules  

[[Page 38239]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0508; Project Identifier MCAI-2021-00070-T]
RIN 2120-AA64


Airworthiness Directives; ATR-GIE Avions de Transport 
R[eacute]gional Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to supersede Airworthiness Directive (AD) 
2021-03-03, which applies to certain ATR-GIE Avions de Transport 
R[eacute]gional Model ATR72 airplanes. AD 2021-03-03 requires revising 
the existing maintenance or inspection program, as applicable, to 
incorporate new or more restrictive airworthiness limitations. Since 
the FAA issued AD 2021-03-03, the FAA has determined that new or more 
restrictive airworthiness limitations are necessary. This proposed AD 
would require revising the existing maintenance or inspection program, 
as applicable, to incorporate new or more restrictive airworthiness 
limitations, as specified in a European Union Aviation Safety Agency 
(EASA) AD, which is proposed for incorporation by reference. The FAA is 
proposing this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by September 
3, 2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For material that will be incorporated by reference (IBR) in this 
AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 8999 000; email ADs@easa.europa.eu; internet 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at https://ad.easa.europa.eu. You may view this IBR material at the 
FAA, Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability of 
this material at the FAA, call 206-231-3195. It is also available in 
the AD docket on the internet at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0508.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
0508; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, any comments received, and other information. The street 
address for Docket Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Shahram Daneshmandi, Aerospace 
Engineer, Large Aircraft Section, International Validation Branch, FAA, 
2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-
3220; email shahram.daneshmandi@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2021-0508; Project Identifier 
MCAI-2021-00070-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
the proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this proposed AD.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Shahram Daneshmandi, Aerospace Engineer, Large Aircraft Section, 
International Validation Branch, FAA, 2200 South 216th St., Des Moines, 
WA 98198; telephone and fax 206-231-3220; email 
shahram.daneshmandi@faa.gov. Any commentary that the FAA receives which 
is not specifically designated as CBI will be placed in the public 
docket for this rulemaking.

Background

    The FAA issued AD 2021-03-03, Amendment 39-21406 (86 FR 11103, 
February 24, 2021) (AD 2021-03-03), for certain ATR-GIE Avions de 
Transport R[eacute]gional Model ATR72 airplanes. AD 2021-03-03 requires 
revising the existing maintenance or inspection program, as applicable, 
to incorporate new or more restrictive airworthiness limitations. The 
FAA issued AD 2021-03-03 to address fatigue cracking and damage in 
principal structural elements, which

[[Page 38240]]

could result in reduced structural integrity of the airplane.

Actions Since AD 2021-03-03 Was Issued

    Since the FAA issued AD 2021-03-03, the FAA has determined that new 
or more restrictive airworthiness limitations are necessary.
    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2021-0020, dated January 15, 2021 
(EASA AD 2021-0020) (also referred to as the Mandatory Continuing 
Airworthiness Information, or the MCAI), to correct an unsafe condition 
for all ATR-GIE Avions de Transport R[eacute]gional Model ATR72 
airplanes. EASA AD 2020-0020 refers to ATR ATR72 Time Limits Document. 
Revision 18, dated October 9, 2020. Airplanes with an original 
airworthiness certificate or original export certificate of 
airworthiness issued after October 9, 2020, must comply with the 
airworthiness limitations specified as part of the approved type design 
and referenced on the type certificate data sheet; this AD therefore 
does not include those airplanes in the applicability.
    This proposed AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
proposing this AD to address fatigue cracking and damage in principal 
structural elements, which could result in reduced structural integrity 
of the airplane. See the MCAI for additional background information.

Related Service Information Under 1 CFR Part 51

    EASA AD 2021-0020 describes new or more restrictive airworthiness 
limitations for airplane structures and safe life limits.
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is proposing this AD because the FAA 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Proposed AD Requirements

    This proposed AD would retain all of the requirements of AD 2021-
03-03. This proposed AD would also require revising the existing 
maintenance or inspection program, as applicable, to incorporate new or 
more restrictive airworthiness limitations, which are specified in EASA 
AD 2021-0020 described previously, as incorporated by reference. Any 
differences with EASA AD 2021-0020 are identified as exceptions in the 
regulatory text of this AD.
    This proposed AD would require revisions to certain operator 
maintenance documents to include new actions (e.g., inspections). 
Compliance with these actions is required by 14 CFR 91.403(c). For 
airplanes that have been previously modified, altered, or repaired in 
the areas addressed by this proposed AD, the operator may not be able 
to accomplish the actions described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must request 
approval for an alternative method of compliance according to paragraph 
(m)(1) of this proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to use this process. As a result, EASA AD 2021-0020 
will be incorporated by reference in the FAA final rule. This proposed 
AD would, therefore, require compliance with EASA AD 2021-0020 in its 
entirety, through that incorporation, except for any differences 
identified as exceptions in the regulatory text of this proposed AD. 
Using common terms that are the same as the heading of a particular 
section in the EASA AD does not mean that operators need comply only 
with that section. For example, where the AD requirement refers to 
``all required actions and compliance times,'' compliance with this AD 
requirement is not limited to the section titled ``Required Action(s) 
and Compliance Time(s)'' in the EASA AD.
    Service information specified in EASA AD 2021-0020 that is required 
for compliance with EASA AD 2021-0020 will be available on the internet 
at https://www.regulations.gov by searching for and locating Docket No. 
FAA-2021-0508 after the FAA final rule is published.

Airworthiness Limitation ADs Using the New Process

    The FAA's process of incorporating by reference MCAI ADs as the 
primary source of information for compliance with corresponding FAA ADs 
has been limited to certain MCAI ADs (primarily those with service 
bulletins as the primary source of information for accomplishing the 
actions required by the FAA AD). However, the FAA is now expanding the 
process to include MCAI ADs that require a change to airworthiness 
limitation documents, such as airworthiness limitation sections.
    For these ADs that incorporate by reference an MCAI AD that changes 
airworthiness limitations, the FAA requirements are unchanged. 
Operators must revise the existing maintenance or inspection program, 
as applicable, to incorporate the information specified in the new 
airworthiness limitation document. The airworthiness limitations must 
be followed according to 14 CFR 91.403(c) and 91.409(e).
    The previous format of the airworthiness limitation ADs included a 
paragraph that specified that no alternative actions (e.g., 
inspections) or intervals may be used unless the actions and intervals 
are approved as an alternative method of compliance (AMOC) in 
accordance with the procedures specified in the AMOCs paragraph under 
``Other FAA Provisions.'' This new format includes a ``New Provisions 
for Alternative Actions and Intervals'' paragraph that does not 
specifically refer to AMOCs, but operators may still request an AMOC to 
use an alternative action or interval.

Costs of Compliance

    The FAA estimates that this proposed AD affects 23 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:
    The FAA estimates the total cost per operator for the retained 
actions from AD 2021-03-03 to be $7,650 (90 work-hours x $85 per work-
hour).
    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although the agency recognizes that this number may vary from operator 
to operator. Since operators incorporate maintenance or inspection 
program changes for their affected fleet(s), the FAA has determined 
that a per-operator estimate is more accurate than a per-airplane 
estimate.

[[Page 38241]]

    The FAA estimates the total cost per operator for the new proposed 
actions to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by
0
a. Removing Airworthiness Directive (AD) 2021-03-03, Amendment 39-21406 
(86 FR 11103, February 24, 2021), and
0
b. Adding the following new AD:

ATR-GIE Avions de Transport R[eacute]gional: Docket No. FAA-2021-
0508; Project Identifier MCAI-2021-00070-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by September 3, 2021.

(b) Affected ADs

    This AD replaces AD 2021-03-03, Amendment 39-21406 (86 FR 11103, 
February 24, 2021) (AD 2021-03-03).

(c) Applicability

    This AD applies to ATR-GIE Avions de Transport R[eacute]gional 
Model ATR72-101, -102, -201, -202, -211, -212, and -212A airplanes, 
certificated in any category, with an original airworthiness 
certificate or original export certificate of airworthiness issued 
on or before October 9, 2020.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Reason

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
issuing this AD to address fatigue cracking and damage in principal 
structural elements, which could result in reduced structural 
integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Retained Maintenance or Inspection Program Revision, With No 
Changes

    This paragraph restates the requirements of paragraph (k) of AD 
2021-03-03, with no changes. For airplanes with an original 
airworthiness certificate or original export certificate of 
airworthiness issued on or before December 12, 2019, except as 
specified in paragraph (h) of this AD: Comply with all required 
actions and compliance times specified in, and in accordance with, 
European Union Aviation Safety Agency (EASA) AD 2020-0173, dated 
August 5, 2020 (EASA AD 2020-0173). Accomplishing the maintenance or 
inspection program revision required by paragraph (j) of this AD 
terminates the requirements of this paragraph.

(h) Retained Exceptions to EASA AD 2020-0173, With Revised Exceptions

    This paragraph restates the requirements of paragraph (l) of AD 
2021-03-03, with revised exceptions.
    (1) Where EASA AD 2020-0173 refers to its effective date, this 
AD requires using March 31, 2021 (the effective date of AD 2021-03-
03).
    (2) The requirements specified in paragraphs (1) and (3) of EASA 
AD 2020-0173 do not apply to this AD.
    (3) Paragraph (4) of EASA AD 2020-0173 specifies revising ``the 
approved AMP [aircraft maintenance program]'' within 12 months after 
its effective date, but this AD requires revising the existing 
maintenance or inspection program, as applicable, to incorporate the 
``limitations, tasks and associated thresholds and intervals'' 
specified in paragraph (4) of EASA AD 2020-0173 within 90 days after 
March 31, 2021 (the effective date of AD 2021-03-03).
    (4) Except as provided by paragraph (2) of EASA AD 2020-0173, 
the initial compliance time for doing the tasks specified in 
paragraph (4) of EASA AD 2020-0173 is at the applicable ``associated 
thresholds'' specified in paragraph (4) of EASA AD 2020-0173, or 
within 90 days after March 31, 2021 (the effective date of AD 2021-
03-03), whichever occurs later.
    (5) The provisions specified in paragraphs (5) and (6) of EASA 
AD 2020-0173 do not apply to this AD.
    (6) The ``Remarks'' section of EASA AD 2020-0173 does not apply 
to this AD.

(i) Retained Restrictions on Alternative Actions and Intervals, With a 
New Exception

    This paragraph restates the requirements of paragraph (m) of AD 
2021-03-03, with a new exception. Except as required by paragraph 
(j) of this AD, after the maintenance or inspection program has been 
revised as required by paragraph (g) of this AD, no alternative 
actions (e.g., inspections) or intervals, are allowed unless they 
are approved as specified in the provisions of the ``Ref. 
Publications'' section of EASA AD 2020-0173.

(j) New Maintenance Program Revision

    Except as specified in paragraph (k) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2021-0020, dated January 15, 2021 (EASA AD 
2021-0020). Accomplishing the maintenance or inspection program 
revision required by this paragraph terminates the requirements of 
paragraph (g) of this AD.

(k) Exceptions to EASA AD 2021-0020

    (1) Where EASA AD 2021-0020 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The requirements specified in paragraphs (1) and (2) of EASA 
AD 2021-0020 do not apply to this AD.
    (3) Paragraph (3) of EASA AD 2021-0020 specifies revising ``the 
approved AMP'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, within 90 days after the effective date of this AD.
    (4) Except as provided by Note 1 of EASA AD 2021-0020, the 
initial compliance time for doing the tasks specified in paragraph 
(3) of EASA AD 2021-0020 is at the applicable ``thresholds'' as 
incorporated by the requirements of paragraph (3) of EASA AD 2021-
0020, or within 90 days after the

[[Page 38242]]

effective date of this AD, whichever occurs later.
    (5) The provisions specified in paragraphs (4) and (5) of EASA 
AD 2021-0020 do not apply to this AD.
    (6) The ``Remarks'' section of EASA AD 2021-0020 does not apply 
to this AD.

(l) New Provisions for Alternative Actions and Intervals

    After the maintenance or inspection program has been revised as 
required by paragraph (j) of this AD, no alternative actions (e.g., 
inspections) and intervals are allowed unless they are approved as 
specified in the provisions of the ``Ref. Publications'' section of 
EASA AD 2021-0020.

(m) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the Large Aircraft Section, International Validation 
Branch, send it to the attention of the person identified in 
paragraph (n)(2) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or ATR-GIE 
Avions de Transport R[eacute]gional's EASA Design Organization 
Approval (DOA). If approved by the DOA, the approval must include 
the DOA-authorized signature.

(n) Related Information

    (1) For information about EASA AD 2021-0020, contact EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email ADs@easa.europa.eu; internet www.easa.europa.eu. You 
may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195. This material may be 
found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2021-0508.
    (2) For more information about this AD, contact Shahram 
Daneshmandi, Aerospace Engineer, Large Aircraft Section, 
International Validation Branch, FAA, 2200 South 216th St., Des 
Moines, WA 98198; telephone and fax 206-231-3220; email 
shahram.daneshmandi@faa.gov.

    Issued on June 17, 2021.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2021-15333 Filed 7-19-21; 8:45 am]
BILLING CODE 4910-13-P


