[Federal Register Volume 86, Number 127 (Wednesday, July 7, 2021)]
[Proposed Rules]
[Pages 35690-35692]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-14401]



[[Page 35690]]

=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0505; Project Identifier 2018-SW-004-AD]
RIN 2120-AA64


Airworthiness Directives; Leonardo S.p.a. Helicopters

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Leonardo S.p.a. Model AB139 and AW139 helicopters. This 
proposed AD was prompted by reports of spurious in-flight 
disconnections of the automatic flight control system (AFCS). This 
proposed AD would require updating certain ``Primus Epic'' system 
software, as specified in a European Aviation Safety Agency (now 
European Union Aviation Safety Agency) (EASA) AD, which is proposed for 
incorporation by reference (IBR). The FAA is proposing this AD to 
address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by August 23, 
2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For EASA material that is proposed for IBR in this AD, contact 
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email ADs@easa.europa.eu; internet www.easa.europa.eu. You 
may find this IBR material on the EASA website at https://ad.easa.europa.eu. You may view EASA material at the FAA, Office of the 
Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-321, 
Fort Worth, TX 76177. For information on the availability of EASA 
material at the FAA, call (817) 222-5110. The EASA material is also 
available at https://www.regulations.gov by searching for and locating 
Docket No. FAA-2021-0505.

Examining the AD Docket

    You may examine the AD docket at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0505; or in person at 
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, 
except Federal holidays. The AD docket contains this NPRM, the EASA AD, 
any comments received, and other information. The street address for 
Docket Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Hal Jensen, Aerospace Engineer, 
Operational Safety Branch, Compliance & Airworthiness Division, FAA, 
950 L'Enfant Plaza N SW, Washington, DC 20024; telephone (202) 267-
9167; email hal.jensen@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2021-0505; Project Identifier 
2018-SW-004-AD'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to Hal 
Jensen, Aerospace Engineer, Operational Safety Branch, Compliance & 
Airworthiness Division, FAA, 950 L'Enfant Plaza N SW, Washington, DC 
20024; telephone (202) 267-9167; email hal.jensen@faa.gov. Any 
commentary that the FAA receives that is not specifically designated as 
CBI will be placed in the public docket for this rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2018-0002, dated January 4, 2018 
(EASA AD 2018-0002), to correct an unsafe condition for certain 
Leonardo S.p.a. Model AB139 and AW139 helicopters.
    This proposed AD was prompted by reports of spurious in-flight 
disconnections of the AFCS. The investigation revealed that these AFCS 
disconnect events relate to un-commanded single channel autopilot 
disengagement for most of the cases, and to some instances of untimely 
dual channel autopilot disengagement. The disconnections occurred in 
random flight conditions and appeared to be temporary disruptions of 
the AFCS' full availability because all functionalities could be 
restored by re-engaging the complete system through the AFCS control 
panel. The FAA is proposing this AD to address spurious degradation or 
unavailability of the full availability of the AFCS. The unsafe 
condition, if not addressed, could result in temporary impairment of 
the automated flight aid for control of the helicopter and increase the 
flightcrew's workload. See EASA AD 2018-0002 for additional background 
information.

FAA's Determination

    These helicopters have been approved by EASA and are approved for 
operation in the United States. Pursuant to the FAA's bilateral 
agreement with the European Union, EASA has notified the FAA about the 
unsafe condition described in its AD. The FAA is proposing this AD 
after evaluating all known relevant information and determining that 
the unsafe condition described previously is likely to exist or develop 
on other helicopters of these same type designs.

[[Page 35691]]

Related Service Information Under 1 CFR Part 51

    EASA AD 2018-0002 requires installation of certain ``Primus Epic'' 
system software, depending on the helicopter configuration. EASA AD 
2018-0002 allows installation of ``Primus Epic'' system software on a 
helicopter after that helicopter has had the software upgrade 
installed.
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2018-0002, described previously, as incorporated by 
reference, except for any differences identified as exceptions in the 
regulatory text of this proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use certain civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, 
EASA AD 2018-0002 will be incorporated by reference in the FAA final 
rule. This proposed AD would, therefore, require compliance with EASA 
AD 2018-0002 in its entirety, through that incorporation, except for 
any differences identified as exceptions in the regulatory text of this 
proposed AD. Using common terms that are the same as the heading of a 
particular section in EASA AD 2018-0002 does not mean that operators 
need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2018-
0002. Service information specified in EASA AD 2018-0002 that is 
required for compliance with it will be available at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
0505 after the FAA final rule is published.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 128 helicopters of U.S. registry. The FAA estimates the 
following costs to comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
                Action                         Labor cost           Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Software upgrade......................  24 work-hours x $85 per               $0          $2,040        $261,120
                                         hour = $2,040.
----------------------------------------------------------------------------------------------------------------

    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this proposed AD may be covered under warranty, thereby reducing the 
cost impact on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Leonardo S.p.a.: Docket No. FAA-2021-0505; Project Identifier 2018-
SW-004-AD.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by August 23, 2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Leonardo S.p.a. Model AB139 and AW139 
helicopters, certificated in any category, identified in paragraphs 
(c)(1) and (2) of this AD, equipped with ``Primus Epic'' system 
software release 7.4 (Phase 7 V1), 7.7 (Phase 7 V3) or 7.10 (Phase 7 
V4).
    (1) Model AB139 and AW19 helicopters having serial number (S/N) 
31005, 31006, and S/Ns 31008 through 31157 inclusive; and S/Ns 41001 
through 41023 inclusive.
    (2) Model AW139 helicopters having S/N 31201 and subsequent, and 
S/N 41201 and subsequent.

(d) Subject

    Joint Aircraft Service Component (JASC) Code: 2200, Auto Flight 
System.

(e) Unsafe Condition

    This AD was prompted by reports of spurious in-flight 
disconnections of the automatic flight control system (AFCS). The

[[Page 35692]]

FAA is issuing this AD to address spurious degradation or 
unavailability of the full AFCS. The unsafe condition, if not 
addressed, could result in temporary impairment of the automated 
flight aid for control of the helicopter and increase the 
flightcrew's workload.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Aviation Safety Agency (now European Union 
Aviation Safety Agency) (EASA) AD 2018-0002, dated January 4, 2018 
(EASA AD 2018-0002).

(h) Exceptions to EASA AD 2018-0002

    (1) Where EASA AD 2018-0002 refers to flight hours (FH), this AD 
requires using hours time-in-service.
    (2) Where EASA AD 2018-0002 refers to its effective date, this 
AD requires using the effective date of this AD.
    (3) The ``Remarks'' section of EASA AD 2018-0002 does not apply 
to this AD.
    (4) Where the service information referenced in EASA AD 2018-
0002 specifies to download an option file from a certain website, 
that method of installation is not required by this AD.

(i) No Reporting Requirement

    Although the service information referenced in EASA AD 2018-0002 
specifies to submit certain information to the manufacturer, this AD 
does not include that requirement.

(j) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, International Validation Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the manager of the International Validation Branch, send 
it to the attention of the person identified in paragraph (k)(2) of 
this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.

(k) Related Information

    (1) For EASA AD 2018-0002, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
ADs@easa.europa.eu; internet www.easa.europa.eu. You may view this 
material at the FAA, Office of the Regional Counsel, Southwest 
Region, 10101 Hillwood Pkwy., Room 6N-321, Fort Worth, TX 76177. For 
information on the availability of this material at the FAA, call 
(817) 222-5110. This material may be found in the AD docket at 
https://www.regulations.gov by searching for and locating Docket No. 
FAA-2021-0505.
    (2) For more information about this AD, contact Hal Jensen, 
Aerospace Engineer, Operational Safety Branch, Compliance & 
Airworthiness Division, FAA, 950 L'Enfant Plaza N SW, Washington, DC 
20024; telephone (202) 267-9167; email hal.jensen@faa.gov.

    Issued on June 15, 2021.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2021-14401 Filed 7-6-21; 8:45 am]
BILLING CODE 4910-13-P


