[Federal Register Volume 86, Number 120 (Friday, June 25, 2021)]
[Proposed Rules]
[Pages 33574-33576]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-13407]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0451; Project Identifier AD-2021-00007-T]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to supersede Airworthiness Directive (AD) 
2019-01-08, which applies to certain The Boeing Company Model 777-200, 
-200LR, -300, and -300ER series airplanes. AD 2019-01-08 requires 
modifications for galley mounted attendant seat fittings. Since the FAA 
issued AD 2019-01-08, the FAA determined that additional airplanes are 
subject to the unsafe condition. This proposed AD would retain the 
requirements of AD 2019-01-18 and expand the applicability to include 
additional airplanes. The FAA is proposing this AD to address the 
unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD August 9, 
2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; internet https://www.myboeingfleet.com. You may 
view this service information at the FAA, Airworthiness Products 
Section, Operational Safety Branch, 2200 South 216th St., Des Moines, 
WA. For information on the availability of this material at the FAA, 
call 206-231-3195. It is also available at https://www.regulations.gov 
by searching for and locating Docket No. FAA-2021-0451.

Examining the AD Docket

    You may examine the AD docket at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0451; or in person at 
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, 
except Federal holidays. The AD docket contains this NPRM, any comments 
received, and other information. The street address for Docket 
Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Brandon Lucero, Aerospace Engineer, 
Cabin Safety and Environmental Systems Section, FAA, Seattle ACO 
Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206-
231-3569; email: brandon.lucero@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2021-0451; Project Identifier 
AD-2021-00007-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
the proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this proposed AD.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Brandon Lucero, Aerospace Engineer, Cabin Safety and Environmental 
Systems Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des 
Moines, WA 98198; phone and fax: 206-231-3569; email: 
brandon.lucero@faa.gov. Any commentary that the FAA receives which is 
not specifically designated as CBI will be placed in the public docket 
for this rulemaking.

Background

    The FAA issued AD 2019-01-08, Amendment 39-19547 (84 FR 4318,

[[Page 33575]]

February 15, 2019) (AD 2019-01-08), for certain The Boeing Company 
Model 777-200, -200LR, -300, and -300ER series airplanes. AD 2019-01-08 
was prompted by a report that showed non-compliance exists on some in-
service galley mounted attendant seat fitting installations. AD 2019-
01-08 requires modifications for galley mounted attendant seat 
fittings. The agency issued AD 2019-01-08 to address non-compliant 
flight attendant seats, which could fail in a high-G crash and result 
in potential injury to flight attendants and consequent inability of 
the flight attendants to assist with passenger evacuation in a timely 
manner.

Actions Since AD 2019-01-08 Was Issued

    Since the FAA issued AD 2019-01-08, an operator reported that line 
numbers (L/Ns) 413, 421, 424, 425, 426, and 439, which are equipped 
with galley part number (P/N) 1013G42A00000 (one of the affected part 
numbers identified in Boeing Special Attention Service Bulletin 777-25-
0649, Revision 1, dated October 6, 2017) were not included in AD 2019-
01-08. A subsequent investigation by Boeing determined that L/Ns 1111, 
1115, and 1137 were also missing from the effectivity of Boeing Special 
Attention Service Bulletin 777-25-0649, Revision 1, dated October 6, 
2017, and therefore not included in the applicability of AD 2019-01-08.

FAA's Determination

    The FAA is issuing this NPRM after determining that the unsafe 
condition described previously is likely to exist or develop on other 
products of the same type design.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Boeing Special Attention Service Bulletin 777-25-
0649, Revision 2, dated October 8, 2020. This service information 
specifies procedures for modifying galley mounted attendant seat 
fittings. This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

Proposed AD Requirements in This NPRM

    Although this proposed AD does not explicitly restate the 
requirements of AD 2019-01-08, this proposed AD would retain all of the 
requirements of AD 2019-01-08. Those requirements are referenced in the 
service information identified previously, which, in turn, is 
referenced in paragraph (g) of this proposed AD. This proposed AD would 
add airplanes to the applicability. This proposed AD would also require 
accomplishment of the actions identified as ``RC'' (required for 
compliance) in the Accomplishment Instructions of Boeing Special 
Attention Service Bulletin 777-25-0649, Revision 2, dated October 8, 
2020, described previously.
    For information on the procedures and compliance times, see this 
service information at https://www.regulations.gov by searching for and 
locating Docket No. FAA-2021-0451.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 50 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
                Action                         Labor cost           Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Modification..........................  7 work-hours x $85 per                $0            $595         $29,750
                                         hour = $595.
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that the proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by:
0
a. Removing Airworthiness Directive 2019-01-08, Amendment 39-19547 (84 
FR 4318, February 15, 2019), and
0
b. Adding the following new airworthiness directive:

The Boeing Company: Docket No. FAA-2021-0451; Project Identifier AD-
2021-00007-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) action by August 9, 2021.

(b) Affected ADs

    This AD replaces AD 2019-01-08, Amendment 39-19547 (84 FR 4318, 
February 15, 2019) (AD 2019-01-08).

[[Page 33576]]

(c) Applicability

    This AD applies to The Boeing Company Model 777-200, -200LR, -
300, and -300ER series airplanes, certificated in any category, as 
identified in Boeing Special Attention Service Bulletin 777-25-0649, 
Revision 2, dated October 8, 2020.

(d) Subject

    Air Transport Association (ATA) of America Code 25, Equipment/
furnishings.

(e) Unsafe Condition

    This AD was prompted by a report that showed a non-compliance 
exists on some in-service galley attendant seat fitting 
installations, and a determination that additional airplanes are 
subject to the unsafe condition. The FAA is issuing this AD to 
address non-compliant flight attendant seats, which could fail in a 
high-G crash and result in potential injury to flight attendants and 
consequent inability of the flight attendants to assist with 
passenger evacuation in a timely manner.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as specified by paragraph (h) of this AD: At the 
applicable times specified in paragraph 1.E., ``Compliance,'' of 
Boeing Special Attention Service Bulletin 777-25-0649, Revision 2, 
dated October 8, 2020, do all applicable actions identified as 
``RC'' (required for compliance) in, and in accordance with, the 
Accomplishment Instructions of Boeing Special Attention Service 
Bulletin 777-25-0649, Revision 2, dated October 8, 2020.

(h) Exception to Service Information Specifications

    Where Boeing Special Attention Service Bulletin 777-25-0649, 
Revision 2, dated October 8, 2020, uses the phrase ``the Revision 2 
date of this service bulletin,'' this AD requires using ``the 
effective date of this AD.''

(i) No Reporting Requirement

    Although the service information referenced in Boeing Special 
Attention Service Bulletin 777-25-0649, Revision 2, dated October 8, 
2020, specifies to submit certain information to the manufacturer, 
this AD does not include that requirement.

(j) Credit for Previous Actions

    This paragraph provides credit for the actions specified in 
paragraph (g) of this AD, if those actions were performed before the 
effective date of this AD using Boeing Special Attention Service 
Bulletin 777-25-0649, Revision 1, dated October 6, 2017 (which is 
incorporated by reference in AD 2019-01-08).

(k) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO Branch, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or responsible Flight Standards Office, 
as appropriate. If sending information directly to the manager of 
the certification office, send it to the attention of the person 
identified in Related Information. Information may be emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the responsible Flight Standards Office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by The Boeing Company Organization Designation 
Authorization (ODA) that has been authorized by the Manager, Seattle 
ACO Branch, FAA, to make those findings. To be approved, the repair 
method, modification deviation, or alteration deviation must meet 
the certification basis of the airplane, and the approval must 
specifically refer to this AD.
    (4) AMOCs approved for AD 2019-01-08 are approved as AMOCs for 
the corresponding provisions of Boeing Special Attention Service 
Bulletin 777-25-0649, Revision 2, dated October 8, 2020, that are 
required by paragraph (g) of this AD.
    (5) For service information that contains steps that are labeled 
as Required for Compliance (RC), the provisions of paragraphs 
(k)(5)(i) and (ii) of this AD apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. If a step or substep is labeled ``RC Exempt,'' then the 
RC requirement is removed from that step or substep. An AMOC is 
required for any deviations to RC steps, including substeps and 
identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(l) Related Information

    (1) For more information about this AD, contact Brandon Lucero, 
Aerospace Engineer, Cabin Safety and Environmental Systems Section, 
FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; 
phone and fax: 206-231-3569; email: brandon.lucero@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Airworthiness Products Section, Operational 
Safety Branch, 2200 South 216th St., Des Moines, WA. For information 
on the availability of this material at the FAA, call 206-231-3195.

    Issued on May 28, 2021.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2021-13407 Filed 6-24-21; 8:45 am]
BILLING CODE 4910-13-P


