[Federal Register Volume 86, Number 103 (Tuesday, June 1, 2021)]
[Rules and Regulations]
[Pages 29178-29180]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-11427]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0030; Project Identifier MCAI-2020-01395-T; 
Amendment 39-21555; AD 2021-10-22]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc., Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Bombardier, Inc., Model BD-700-1A10 airplanes. This AD was 
prompted by a report indicating that during installation, a fuel pipe 
bracket assembly on the intermediate rib in the center fuel tank was 
mislocated, resulting in an offset between the fitting assembly and the 
refuel/defuel tube assembly. This AD requires modification of the fuel 
pipe bracket assembly, including all related investigative actions and 
corrective actions, if necessary; and performing an operational test of 
the refuel and defuel system. The FAA is issuing this AD to address the 
unsafe condition on these products.

DATES: This AD is effective July 6, 2021.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of July 6, 
2021.

ADDRESSES: For service information identified in this final rule, 
contact Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email thd.crj@aero.bombardier.com; internet https://

[[Page 29179]]

www.bombardier.com. You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195. It is also available on the 
internet at https://www.regulations.gov by searching for and locating 
Docket No. FAA-2021-0030.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
0030; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Siddeeq Bacchus, Aerospace Engineer, 
Mechanical Systems and Administrative Services Section, FAA, New York 
ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone 516-228-7362; fax 516-794-5531; email 9-avs-nyaco-cos@faa.gov.

SUPPLEMENTARY INFORMATION:

Background

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued TCCA AD CF-2020-37, dated October 9, 
2020 (also referred to as the Mandatory Continuing Airworthiness 
Information, or the MCAI), to correct an unsafe condition for certain 
Bombardier, Inc., Model BD-700-1A10 airplanes. You may examine the MCAI 
in the AD docket on the internet at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0030.
    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to certain Bombardier, 
Inc., Model BD-700-1A10 airplanes. The NPRM published in the Federal 
Register on February 24, 2021 (86 FR 11191). The NPRM was prompted by a 
report indicating that during installation, a fuel pipe bracket 
assembly on the intermediate rib in the center fuel tank was 
mislocated, resulting in an offset between the fitting assembly and the 
refuel/defuel tube assembly. The NPRM proposed to require modification 
of the fuel pipe bracket assembly, including all related investigative 
actions and corrective actions, if necessary; and performing an 
operational test of the refuel and defuel system. The FAA is issuing 
this AD to address the offset, which could cause a preload on the fuel 
pipes and reduce their ability to absorb shock or vibration-induced 
loads, making the tube and clamp more prone to stress corrosion 
cracking. This could lead to failure of the coupling and the bracket 
and p-clamp assembly, resulting in fuel leakage and loss of electrical 
bonding between fuel pipes, and lightning-induced sparking that could 
induce fuel ignition. See the MCAI for additional background 
information.

Comments

    The FAA gave the public the opportunity to participate in 
developing this final rule. The FAA received no comments on the NPRM or 
on the determination of the cost to the public.

Conclusion

    The FAA reviewed the relevant data and determined that air safety 
and the public interest require adopting this final rule as proposed, 
except for minor editorial changes. The FAA has determined that these 
minor changes:
     Are consistent with the intent that was proposed in the 
NPRM for addressing the unsafe condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM.

Related Service Information Under 1 CFR Part 51

    Bombardier has issued Service Bulletin 700-28-6006, dated June 1, 
2020. This service information describes procedures for a modification 
of the fuel pipe bracket assembly, including investigative actions (a 
detailed visual inspection of the fuel pipe assembly for any damaged 
paint, permanent deformation, corrosion, cracking, gouges, dents, or 
deep scratches); installation of certain new parts; replacement of the 
fuel pipe and fuel pipe bracket assembly, if necessary; and an 
operational test of the refuel and defuel system. This service 
information is reasonably available because the interested parties have 
access to it through their normal course of business or by the means 
identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 51 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
10 work-hours x $85 per hour = $850..........................            $904           $1,754          $89,454
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary on-
condition action that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need this on-condition action:

                                     Estimated Costs of On-Condition Actions
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                                  Labor cost                                       Parts cost        product
----------------------------------------------------------------------------------------------------------------
3 work-hours x $85 per hour = $255............................................          $1,937           $2,192
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some or all of the costs of this AD 
may be covered under warranty, thereby reducing the cost impact on 
affected operators. The FAA does not control warranty coverage for 
affected operators. As a result, the FAA has included all known costs 
in the cost estimate.

[[Page 29180]]

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2021-10-22 Bombardier, Inc.: Amendment 39-21555; Docket No. FAA-
2021-0030; Project Identifier MCAI-2020-01395-T.

(a) Effective Date

    This airworthiness directive (AD) is effective July 6, 2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc., Model BD-700-1A10 
airplanes, certificated in any category, serial numbers 9657 through 
9844 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 28, Fuel.

(e) Reason

    This AD was prompted by a report indicating that during 
installation, a fuel pipe bracket assembly on the intermediate rib 
in the center fuel tank was mislocated, resulting in an offset 
between the fitting assembly and the refuel/defuel tube assembly. 
The FAA is issuing this AD to address the offset, which could cause 
a preload on the fuel pipes and reduce their ability to absorb shock 
or vibration-induced loads, making the tube and clamp more prone to 
stress corrosion cracking. This could lead to failure of the 
coupling and the bracket and p-clamp assembly, resulting in fuel 
leakage and loss of electrical bonding between fuel pipes, and 
lightning-induced sparking that could induce fuel ignition.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection and Corrective Action

    Within 30 months after the effective date of this AD: Perform a 
modification of the fuel pipe bracket assembly and refuel tube 
assembly; do all related investigative actions and applicable 
corrective actions; and perform an operational test of the refuel 
and defuel system; in accordance with paragraphs 2.B. and 2.C. of 
the Accomplishment Instructions of Bombardier Service Bulletin 700-
28-6006, dated June 1, 2020. All related investigative and 
corrective actions must be done before further flight.

(h) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York ACO Branch, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or responsible Flight Standards Office, as appropriate. If 
sending information directly to the manager of the certification 
office, send it to ATTN: Program Manager, Continuing Operational 
Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before 
using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, New York ACO 
Branch, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If 
approved by the DAO, the approval must include the DAO-authorized 
signature.

(i) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) TCCA AD CF-2020-37, dated October 9, 2020, for related 
information. This MCAI may be found in the AD docket on the internet 
at https://www.regulations.gov by searching for and locating Docket 
No. FAA-2021-0030.
    (2) For more information about this AD, contact Siddeeq Bacchus, 
Aerospace Engineer, Mechanical Systems and Administrative Services 
Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 516-228-7362; fax 516-794-5531; email 
9-avs-nyaco-cos@faa.gov.

(j) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Service Bulletin 700-28-6006, dated June 1, 2020.
    (ii) [Reserved]
    (3) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email thd.crj@aero.bombardier.com; internet https://www.bombardier.com.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, email fedreg.legal@nara.gov, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on May 6, 2021.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2021-11427 Filed 5-28-21; 8:45 am]
BILLING CODE 4910-13-P


