[Federal Register Volume 86, Number 35 (Wednesday, February 24, 2021)]
[Proposed Rules]
[Pages 11156-11158]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-03581]


 ========================================================================
 Proposed Rules
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains notices to the public of 
 the proposed issuance of rules and regulations. The purpose of these 
 notices is to give interested persons an opportunity to participate in 
 the rule making prior to the adoption of the final rules.
 
 ========================================================================
 

  Federal Register / Vol. 86, No. 35 / Wednesday, February 24, 2021 / 
Proposed Rules  

[[Page 11156]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0028; Project Identifier MCAI-2020-01516-T]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for all Airbus SAS Model A319-171N airplanes, Model A320-271N, -272N, 
and -273N airplanes, and Model A321-271N, -272N, -271NX, and -272NX 
airplanes. This proposed AD was prompted by a report indicating that 
during a full scale fatigue test of the forward engine mounts, 
premature wear was identified on the forward engine mount shackle 
assemblies; in addition, during bearing replacement, the bearing lock 
washer was found broken. This proposed AD would require replacing any 
forward engine mount shackle assemblies having a certain part number 
with a serviceable part, and re-identifying the engine mount, or 
replacing any forward engine mount assemblies having a certain part 
number, as specified in a European Union Aviation Safety Agency (EASA) 
AD, which is proposed for incorporation by reference. The FAA is 
proposing this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by April 12, 
2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For material that will be incorporated by reference (IBR) in this 
AD, contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 8999 000; email ADs@easa.europa.eu; internet 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at https://ad.easa.europa.eu. You may view this IBR material at the 
FAA, Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability of 
this material at the FAA, call 206-231-3195. It is also available in 
the AD docket on the internet at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0028.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
0028; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, any comments received, and other information. The street 
address for Docket Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Sanjay Ralhan, Aerospace Engineer, 
Large Aircraft Section, International Validation Branch, FAA, 2200 
South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3223; 
email Sanjay.Ralhan@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2021-0028; Project Identifier 
MCAI-2020-01516-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
the proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this proposed AD.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Sanjay Ralhan, Aerospace Engineer, Large Aircraft Section, 
International Validation Branch, FAA, 2200 South 216th St., Des Moines, 
WA 98198; telephone and fax 206-231-3223; email Sanjay.Ralhan@faa.gov. 
Any commentary that the FAA receives which is not specifically 
designated as CBI will be placed in the public docket for this 
rulemaking.

Background

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2020-0250, dated November 11, 2020 
(EASA AD 2020-0250) (also referred to as the Mandatory Continuing 
Airworthiness Information, or the MCAI), to correct an unsafe condition 
for all Airbus SAS Model A319-171N airplanes, Model A320-271N, -272N, 
and -273N airplanes, and Model A321-

[[Page 11157]]

271N, -272N, -271NX, and -272NX airplanes.
    This proposed AD was prompted by a report indicating that during a 
full scale fatigue test of the forward engine mounts, premature wear 
was identified on the forward engine mount shackle assemblies; in 
addition, during bearing replacement, the bearing lock washer was found 
broken. The FAA is proposing this AD to address premature wear and 
broken bearing lock washers at the forward engine mounts, which could 
lead to overload of the forward engine mount beams and engine mount 
failure, with consequent in-flight engine detachment, and possibly 
result in reduced controllability of the airplane. See the MCAI for 
additional background information.

Related Service Information Under 1 CFR Part 51

    EASA AD 2020-0250 describes procedures for replacing any forward 
engine mount shackle assemblies having part number D7121513500xxx 
(`xxx' can be any numerical value) with a serviceable part, and re-
identifying the engine mount, or replacing any forward engine mount 
assemblies having part number D7121506500xxx (`xxx' can be any 
numerical value) and fitted with an affected engine mount shackle 
assembly. This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is proposing this AD because the FAA 
evaluated all the relevant information and determined the unsafe 
condition described previously is likely to exist or develop in other 
products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2020-0250 described previously, as incorporated by 
reference, except for any differences identified as exceptions in the 
regulatory text of this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to use this process. As a result, EASA AD 2020-0250 
will be incorporated by reference in the FAA final rule. This proposed 
AD would, therefore, require compliance with EASA AD 2020-0250 in its 
entirety, through that incorporation, except for any differences 
identified as exceptions in the regulatory text of this proposed AD. 
Using common terms that are the same as the heading of a particular 
section in the EASA AD does not mean that operators need comply only 
with that section. For example, where the AD requirement refers to 
``all required actions and compliance times,'' compliance with this AD 
requirement is not limited to the section titled ``Required Action(s) 
and Compliance Time(s)'' in the EASA AD. Service information specified 
in EASA AD 2020-0250 that is required for compliance with EASA AD 2020-
0250 will be available on the internet at https://www.regulations.gov 
by searching for and locating Docket No. FAA-2021-0028 after the FAA 
final rule is published.

Costs of Compliance

    The FAA estimates that this proposed AD affects 70 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
              Labor cost                      Parts cost            Cost per product      Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
5 work-hours x $85 per hour = $425...  Up to $75,360..........  Up to $75,785..........  Up to $5,304,950.
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some or all of the costs of this 
proposed AD may be covered under warranty, thereby reducing the cost 
impact on affected individuals. The FAA does not control warranty 
coverage for affected individuals. As a result, the FAA has included 
all known costs in the cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator,

[[Page 11158]]

the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Airbus SAS: Docket No. FAA-2021-0028; Project Identifier MCAI-2020-
01516-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) action by April 12, 2021.

(b) Affected Airworthiness Directives (ADs)

    None.

(c) Applicability

    This AD applies to all Airbus SAS Model A319-171N airplanes, 
Model A320-271N, -272N, and -273N airplanes, and Model A321-271N, -
272N, -271NX, and -272NX airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 71, Powerplant.

(e) Reason

    This AD was prompted by a report indicating that during a full 
scale fatigue test of the forward engine mounts, premature wear was 
identified on the forward engine mount shackle assemblies; in 
addition, during bearing replacement, the bearing lock washer was 
found broken. The FAA is issuing this AD to address premature wear 
and broken bearing lock washers at the forward engine mounts, which 
could lead to overload of the forward engine mount beams and engine 
mount failure, with consequent in-flight engine detachment, and 
possibly result in reduced controllability of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) AD 
2020-0250, dated November 11, 2020 (EASA AD 2020-0250).

(h) Exceptions to EASA AD 2020-0250

    (1) Where EASA AD 2020-0250 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2020-0250 does not apply 
to this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (j)(2) of 
this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Airbus 
SAS's EASA Design Organization Approval (DOA). If approved by the 
DOA, the approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (i)(2) of this AD, if any service information contains 
procedures or tests that are identified as RC, those procedures and 
tests must be done to comply with this AD; any procedures or tests 
that are not identified as RC are recommended. Those procedures and 
tests that are not identified as RC may be deviated from using 
accepted methods in accordance with the operator's maintenance or 
inspection program without obtaining approval of an AMOC, provided 
the procedures and tests identified as RC can be done and the 
airplane can be put back in an airworthy condition. Any 
substitutions or changes to procedures or tests identified as RC 
require approval of an AMOC.

(j) Related Information

    (1) For information about EASA AD 2020-0250, contact the EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email ADs@easa.europa.eu; internet www.easa.europa.eu. You 
may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195. This material may be 
found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2021-0028.
    (2) For more information about this AD, contact Sanjay Ralhan, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3223; email Sanjay.Ralhan@faa.gov.

    Issued on February 4, 2021.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2021-03581 Filed 2-23-21; 8:45 am]
BILLING CODE 4910-13-P


