[Federal Register Volume 86, Number 9 (Thursday, January 14, 2021)]
[Rules and Regulations]
[Pages 2961-2964]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-00807]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-1172; Project Identifier MCAI-2020-01661-T; 
Amendment 39-21388; AD 2021-02-05]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Airbus SAS Model A330-200, -200 Freighter, -300, -800, and -900 series 
airplanes; Model A340-200 and -300 series airplanes; and Model A340-541 
and A340-642 airplanes. This AD was prompted by a report that an 
erroneous torque value for the attachment nuts to install a pitot probe 
was included in the affected Aircraft Maintenance Manual (AMM) task. 
This AD requires re-torqueing the attachment nuts of each affected 
part. In addition, this AD prohibits the use of the affected AMM task, 
as specified in a European Union Aviation Safety Agency (EASA) AD, 
which is incorporated by reference. The FAA is issuing this AD to 
address the unsafe condition on these products.

DATES: This AD becomes effective January 29, 2021.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of January 29, 
2021.
    The FAA must receive comments on this AD by March 1, 2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For material incorporated by reference (IBR) in this AD, contact 
the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 
221 8999 000; email ADs@easa.europa.eu; internet www.easa.europa.eu. 
You may find this IBR material on the EASA website at https://ad.easa.europa.eu. You may view this IBR material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195. It is also available in the AD 
docket on the internet at https://www.regulations.gov by searching for 
and locating Docket No. FAA-2020-1172.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
1172; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this AD, any comments received, and other information. The street 
address for Docket Operations is listed above. Comments will be 
available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, 
Large Aircraft Section, International Validation Branch, FAA, 2200 
South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3229; 
email vladimir.ulyanov@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2020-0279, dated December 14, 2020 
(EASA AD 2020-0279) (also referred to as the Mandatory Continuing 
Airworthiness Information, or the MCAI), to correct an unsafe condition 
for all Model A330-201, A330-202, A330-203, A330-223, A330-223F, A330-
243, A330-243F, A330-301, A330-302, A330-303, A330-321, A330-322, A330-
323, A330-341, A330-342, A330-343, A330-743L, A330-841, A330-941, A340-
211, A340-212, A340-213, A340-311, A340-312, A340-313, A340-541, A340-
542, A340-642, and A340-643 airplanes. Model A330-743L, A340-542, and 
A340-643 airplanes are not certificated by the FAA and are not included 
on the U.S. type certificate data sheet; this AD therefore does not 
include those airplanes in the applicability.
    This AD was prompted by a report that an erroneous torque value for 
the attachment nuts to install a pitot probe was included in the 
affected AMM task. The FAA is issuing this AD to address

[[Page 2962]]

the erroneous torque value. If not addressed it could lead to erroneous 
total pressure measurement being relayed to navigation systems, 
possibly resulting in reduced control of the airplane. See the MCAI for 
additional background information.

Related Service Information Under 1 CFR Part 51

    EASA AD 2020-0279 describes procedures for re-torqueing the 
attachment nuts of each affected part and prohibits the use of the 
affected AMM task. This material is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this AD because the FAA evaluated 
all pertinent information and determined the unsafe condition exists 
and is likely to exist or develop on other products of the same type 
design.

Requirements of This AD

    This AD requires accomplishing the actions specified in EASA AD 
2020-0279 described previously, as incorporated by reference, except 
for any differences identified as exceptions in the regulatory text of 
this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to use this process. As a result, EASA AD 2020-0279 
is incorporated by reference in this final rule. This AD, therefore, 
requires compliance with EASA AD 2020-0279 in its entirety, through 
that incorporation, except for any differences identified as exceptions 
in the regulatory text of this AD. Using common terms that are the same 
as the heading of a particular section in the EASA AD does not mean 
that operators need comply only with that section. For example, where 
the AD requirement refers to ``all required actions and compliance 
times,'' compliance with this AD requirement is not limited to the 
section titled ``Required Action(s) and Compliance Time(s)'' in the 
EASA AD. Service information specified in EASA AD 2020-0279 that is 
required for compliance with EASA AD 2020-0279 is available on the 
internet at https://www.regulations.gov by searching for and locating 
Docket No. FAA-2020-1172.

FAA's Justification and Determination of the Effective Date

    An unsafe condition exists that requires the immediate adoption of 
this AD without providing an opportunity for public comments prior to 
adoption. The FAA has found that the risk to the flying public 
justifies waiving notice and comment prior to adoption of this rule 
because an erroneous torque value for the attachment nuts to install a 
pitot probe could lead to erroneous total pressure measurement being 
relayed to navigation systems, possibly resulting in reduced control of 
the airplane. In addition, the compliance time for the required action 
is shorter than the time necessary for the public to comment and for 
publication of the final rule. Therefore, the FAA finds good cause that 
notice and opportunity for prior public comment are impracticable. In 
addition, for the reasons stated above, the FAA finds that good cause 
exists for making this amendment effective in less than 30 days.

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this AD. Send your comments to an address listed under 
ADDRESSES. Include ``Docket No. FAA-2020-1172; Project Identifier MCAI-
2020-01661-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the final rule, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this final rule because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this final rule.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this AD contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this AD, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this AD. Submissions containing CBI should be sent to 
Vladimir Ulyanov, Aerospace Engineer, Large Aircraft Section, 
International Validation Branch, FAA, 2200 South 216th St., Des Moines, 
WA 98198; telephone and fax 206-231-3229; email 
vladimir.ulyanov@faa.gov. Any commentary that the FAA receives which is 
not specifically designated as CBI will be placed in the public docket 
for this rulemaking.

Regulatory Flexibility Act (RFA)

    The requirements of the RFA do not apply when an agency finds good 
cause pursuant to 5 U.S.C. 553 to adopt a rule without prior notice and 
comment. Because the FAA has determined that it has good cause to adopt 
this rule without notice and comment, RFA analysis is not required.

Costs of Compliance

    The FAA estimates that this AD affects 112 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
1 work-hour x $85 per hour = $85.............................              $0              $85           $9,520
----------------------------------------------------------------------------------------------------------------


[[Page 2963]]

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866, and
    (2) Will not affect intrastate aviation in Alaska.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2021-02-05 Airbus SAS: Amendment 39-21388; Docket No. FAA-2020-1172; 
Project Identifier MCAI-2020-01661-T.

(a) Effective Date

    This airworthiness directive (AD) becomes effective January 29, 
2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Airbus SAS airplanes, certificated in any 
category, identified in paragraphs (c)(1) through (9) of this AD.
    (1) Model A330-201, A330-202, A330-203, A330-223, and A330-243 
airplanes.
    (2) Model A330-223F and A330-243F airplanes.
    (3) Model A330-301, A330-302, A330-303, A330-321, A330-322, 
A330-323, A330-341, A330-342, and A330-343 airplanes.
    (4) Model A330-841 airplanes.
    (5) Model A330-941 airplanes.
    (6) Model A340-211, A340-212, and A340-213 airplanes.
    (7) Model A340-311, A340-312, and A340-313 airplanes.
    (8) Model A340-541 airplanes.
    (9) Model A340-642 airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 34, Navigation.

(e) Reason

    This AD was prompted by a report that an erroneous torque value 
for the attachment nuts to install a pitot probe was included in the 
affected Aircraft Maintenance Manual (AMM) task. The FAA is issuing 
this AD to address the erroneous torque value. If not addressed it 
could lead to erroneous total pressure measurement being relayed to 
navigation systems, possibly resulting in reduced control of the 
airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) AD 
2020-0279, dated December 14, 2020 (EASA AD 2020-0279).

(h) Exceptions to EASA AD 2020-0279

    (1) Where EASA AD 2020-0279 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2020-0279 does not apply 
to this AD.

(i) No Reporting Requirement

    Although the service information referenced in EASA AD 2020-0279 
specifies to submit certain information to the manufacturer, this AD 
does not include that requirement.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (k) of this 
AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Airbus 
SAS's EASA Design Organization Approval (DOA). If approved by the 
DOA, the approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (j)(2) of this AD, if any service information referenced 
in EASA AD 2020-0279 that contains paragraphs that are labeled as 
RC, the instructions in RC paragraphs, including subparagraphs under 
an RC paragraph, must be done to comply with this AD; any 
paragraphs, including subparagraphs under those paragraphs, that are 
not identified as RC are recommended. The instructions in 
paragraphs, including subparagraphs under those paragraphs, not 
identified as RC may be deviated from using accepted methods in 
accordance with the operator's maintenance or inspection program 
without obtaining approval of an AMOC, provided the instructions 
identified as RC can be done and the airplane can be put back in an 
airworthy condition. Any substitutions or changes to instructions 
identified as RC require approval of an AMOC.

(k) Related Information

    For more information about this AD, contact Vladimir Ulyanov, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3229; email vladimir.ulyanov@faa.gov.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2020-0279, 
dated December 14, 2020.
    (ii) [Reserved]
    (3) For EASA AD 2020-0279, contact the EASA, Konrad-Adenauer-
Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email 
ADs@easa.europa.eu; internet www.easa.europa.eu. You may find this

[[Page 2964]]

EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195. This material may be found in the AD 
docket on the internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2020-1172.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
fedreg.legal@nara.gov, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on January 7, 2021.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2021-00807 Filed 1-12-21; 11:15 am]
BILLING CODE 4910-13-P


