[Federal Register Volume 86, Number 10 (Friday, January 15, 2021)]
[Proposed Rules]
[Pages 3885-3888]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-29227]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-1167; Project Identifier AD-2020-01007-T]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for all The Boeing Company Model DC-10-10, DC-10-10F, DC-10-15, DC-10-
30, DC-10-30F (KC-10A and KDC-10), DC-10-40 and DC-10-40F airplanes; 
and Model MD-10-10F and MD-10-30F airplanes. This proposed AD was 
prompted by a report that an operator found a crack in the upper flange 
of the pylon aft bulkhead bracket. This proposed AD would require a 
general visual inspection of the left and right wing pylon at the aft 
bulkhead bracket for any lockbolt and collar; repetitive surface and 
open hole eddy current high frequency (ETHF) inspections of the left 
and right wing pylon at the aft bulkhead bracket for any cracking; and 
applicable on-condition actions. The FAA is proposing this AD to 
address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by March 1, 
2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; internet https://www.myboeingfleet.com. You may 
view this referenced service information at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
1167.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
1167; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, any comments received, and other

[[Page 3886]]

information. The street address for Docket Operations is listed above. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Manuel Hernandez, Aerospace Engineer, 
Airframe Section, FAA, Los Angeles ACO Branch, 3960 Paramount 
Boulevard, Lakewood, CA 90712-4137; phone: 562-627-5256; fax: 562-627-
5210; email: Manuel.F.Hernandez@faa.gov.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2020-1167; Project Identifier 
AD-2020-01007-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
the proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact we receive about this proposed AD.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Manuel Hernandez, Aerospace Engineer, Airframe Section, FAA, Los 
Angeles ACO Branch, 3960 Paramount Boulevard, Lakewood, CA 90712-4137; 
phone: 562-627-5256; fax: 562-627-5210; email: 
Manuel.F.Hernandez@faa.gov. Any commentary that the FAA receives which 
is not specifically designated as CBI will be placed in the public 
docket for this rulemaking.

Discussion

    The FAA has received a report indicating that an operator found a 
crack in the upper flange of the pylon aft bulkhead bracket. The crack 
was discovered during an open hole ETHF inspection and was not 
detectable with the fastener installed. Further investigation revealed 
that the crack growth was caused by fatigue loading. This condition, if 
not addressed, could result in possible cracking of the wing pylon at 
the aft bulkhead bracket, which could result in the inability of the 
pylon to sustain limit load and adversely affect the structural 
integrity of the airplane.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Boeing Alert Requirements Bulletin DC10-54A111 RB, 
dated June 26, 2020. The service information describes procedures for a 
general visual inspection of the left and right wing pylon at the aft 
bulkhead bracket for any lockbolt and collar; repetitive surface and 
open hole ETHF inspections of the left and right wing pylon at the aft 
bulkhead bracket for any cracking; and applicable on-condition actions. 
On-condition actions include modifying any aft bulkhead bracket that 
has a lockbolt and collar, and repair or replacement of the aft 
bulkhead bracket.
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    The FAA is proposing this AD because the agency evaluated all the 
relevant information and determined the unsafe condition described 
previously is likely to exist or develop in other products of the same 
type design.

Proposed AD Requirements

    This proposed AD would require accomplishment of the actions 
identified in Boeing Alert Requirements Bulletin DC10-54A111 RB, dated 
June 26, 2020, described previously, except for any differences 
identified as exceptions in the regulatory text of this proposed AD.
    For information on the procedures and compliance times, see this 
service information at https://www.regulations.gov by searching for and 
locating Docket No. FAA-2020-1167.

Explanation of Requirements Bulletin

    The FAA worked in conjunction with industry, under the 
Airworthiness Directive Implementation Aviation Rulemaking Committee 
(AD ARC), to enhance the AD system. One enhancement is a process for 
annotating which steps in the service information are ``required for 
compliance'' (RC) with an AD. Boeing has implemented this RC concept 
into Boeing service bulletins.
    In an effort to further improve the quality of ADs and AD-related 
Boeing service information, a joint process improvement initiative was 
worked between the FAA and Boeing. The initiative resulted in the 
development of a new process in which the service information more 
clearly identifies the actions needed to address the unsafe condition 
in the ``Accomplishment Instructions.'' The new process results in a 
Boeing Requirements Bulletin, which contains only the actions needed to 
address the unsafe condition (i.e., only the RC actions).

Costs of Compliance

    The FAA estimates that this proposed AD affects 103 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                                 Cost on U.S.
              Action                    Labor cost        Parts cost      Cost per product        operators
----------------------------------------------------------------------------------------------------------------
General visual inspection........  2 work-hours x $85               $0  $170...............  $17,510.
                                    per hour = $170.
Surface and open hole ETHF         5 work-hours x $85                0  425 per inspection   8,755 per
 inspections.                       per hour = $425                      cycle.               inspection cycle.
                                    per inspection
                                    cycle.
----------------------------------------------------------------------------------------------------------------


[[Page 3887]]

    The FAA estimates the following costs to do any necessary on-
condition modifications that would be required. The FAA has no way of 
determining the number of aircraft that might need these on-condition 
modifications:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
           Labor cost                 Parts cost       Cost per product
------------------------------------------------------------------------
1 work-hour x $85 per hour = $85  $100 per lockbolt/  $185 per lockbolt/
 per lockbolt/collar (maximum of   collar.             collar.
 8 lockbolt/collars).
------------------------------------------------------------------------

    The FAA has received no definitive data on which to base the cost 
estimates for the on-condition repairs and replacements specified in 
this proposed AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

The Boeing Company: Docket No. FAA-2020-1167; Project Identifier AD-
2020-01007-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by March 1, 2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all The Boeing Company Model airplanes 
specified in paragraphs (c)(1) through (5) of this AD, certificated 
in any category.
    (1) Model DC-10-10 and DC-10-10F airplanes.
    (2) Model DC-10-15 airplanes.
    (3) Model DC-10-30 and DC-10-30F (KC-10A and KDC-10) airplanes.
    (4) Model DC-10-40 and DC-10-40F airplanes.
    (5) Model MD-10-10F and MD-10-30F airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 54, Nacelles/
pylons.

(e) Unsafe Condition

    This AD was prompted by a report that an operator found a crack 
in the upper flange of the pylon aft bulkhead bracket. The FAA is 
issuing this AD to address possible cracking of the wing pylon at 
the aft bulkhead bracket, which could result in the inability of the 
pylon to sustain limit load and adversely affect the structural 
integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as specified by paragraph (h) of this AD: At the 
applicable times specified in the ``Compliance'' paragraph of Boeing 
Alert Requirements Bulletin DC10-54A111 RB, dated June 26, 2020, do 
all applicable actions identified in, and in accordance with, the 
Accomplishment Instructions of Boeing Alert Requirements Bulletin 
DC10-54A111 RB, dated June 26, 2020.

    Note 1 to paragraph (g): Guidance for accomplishing the actions 
required by this AD can be found in Boeing Alert Service Bulletin 
DC10-54A111, dated June 26, 2020, which is referred to in Boeing 
Alert Requirements Bulletin DC10-54A111 RB, dated June 26, 2020.

(h) Exceptions to Service Information Specifications

    (1) Where Boeing Alert Requirements Bulletin DC10-54A111 RB, 
dated June 26, 2020, uses the phrase ``the original issue date of 
Requirements Bulletin DC10-54A111 RB,'' this AD requires using ``the 
effective date of this AD.''
    (2) Where Boeing Alert Requirements Bulletin DC10-54A111 RB, 
dated June 26, 2020, specifies contacting Boeing for repair, 
modification, or replacement instructions: This AD requires doing 
the repair, modification, or replacement using a method approved in 
accordance with the procedures specified in paragraph (i) of this 
AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Los Angeles ACO Branch, FAA, has the authority 
to approve AMOCs for this AD, if requested using the procedures 
found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your 
request to your principal inspector or responsible Flight Standards 
Office, as appropriate. If sending information directly to the 
manager of the certification office, send it to the attention of the 
person identified in paragraph (j)(1) of this AD. Information may be 
emailed to: 9-ANM-LAACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the responsible Flight Standards Office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by The Boeing Company Organization Designation 
Authorization (ODA) that has been authorized by the Manager, Los 
Angeles ACO Branch, FAA, to make those findings. To be approved, the 
repair method, modification deviation, or alteration deviation must 
meet the

[[Page 3888]]

certification basis of the airplane, and the approval must 
specifically refer to this AD.

(j) Related Information

    (1) For more information about this AD, contact Manuel 
Hernandez, Aerospace Engineer, Airframe Section, FAA, Los Angeles 
ACO Branch, 3960 Paramount Boulevard, Lakewood, CA 90712-4137; 
phone: 562-627-5256; fax: 562-627-5210; email: 
Manuel.F.Hernandez@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Airworthiness Products Section, Operational 
Safety Branch, 2200 South 216th St., Des Moines, WA. For information 
on the availability of this material at the FAA, call 206-231-3195.

    Issued on December 18, 2020.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2020-29227 Filed 1-14-21; 8:45 am]
BILLING CODE 4910-13-P


