[Federal Register Volume 85, Number 229 (Friday, November 27, 2020)]
[Proposed Rules]
[Pages 75964-75966]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-26045]



[[Page 75964]]

=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-1035; Project Identifier MCAI-2020-01017-T]
RIN 2120-AA64


Airworthiness Directives; Yabor[atilde] Ind[uacute]stria 
Aeron[aacute]utica S.A. (Type Certificate Previously Held by Embraer 
S.A.) Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Yabor[atilde] Ind[uacute]stria Aeron[aacute]utica S.A. 
Model EMB-135, EMB-145, -145ER, -145MR, -145LR, -145XR, -145MP, and -
145EP airplanes. This proposed AD was prompted by reports that 
calculations provided by the automatic takeoff thrust control system 
(ATTCS) are incorrect under certain conditions. This proposed AD would 
require updating the software of the installed full authority digital 
engine control (FADEC) systems, as specified in an Ag[ecirc]ncia 
Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which will be 
incorporated by reference. The FAA is proposing this AD to address the 
unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by January 11, 
2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For ANAC material incorporated by reference (IBR) in this AD, 
contact National Civil Aviation Agency (ANAC), Aeronautical Products 
Certification Branch (GGCP), Rua Dr. Orlando Feirabend Filho, 230--
Centro Empresarial Aquarius--Torre B--Andares 14 a 18, Parque 
Residencial Aquarius, CEP 12.246-190--S[atilde]o Jos[eacute] dos 
Campos--SP, BRAZIL, Tel: 55 (12) 3203-6600; Email: pac@anac.gov.br; 
internet www.anac.gov.br/en/. You may find this IBR material on the 
ANAC website at https://sistemas.anac.gov.br/certificacao/DA/DAE.asp. 
You may view this IBR material at the FAA, Airworthiness Products 
Section, Operational Safety Branch, 2200 South 216th St., Des Moines, 
WA. For information on the availability of this material at the FAA, 
call 206-231-3195. It is also available in the AD docket on the 
internet at https://www.regulations.gov by searching for and locating 
Docket No. FAA-2020-1035.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
1035; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, any comments received, and other information. The street 
address for Docket Operations is listed above. Comments will be 
available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Kathleen Arrigotti, Aerospace 
Engineer, Large Aircraft Section, International Validation Branch, FAA, 
2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-
3218; email kathleen.arrigotti@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to participate in this rulemaking by submitting 
written comments, data, or views about this proposal. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. To 
ensure the docket does not contain duplicate comments, commenters 
should send only one copy of written comments, or if comments are filed 
electronically, commenters should submit only one time. Send your 
comments to an address listed under the ADDRESSES section. Include 
``Docket No. FAA-2020-1035; Project Identifier MCAI-2020-01017-T'' at 
the beginning of your comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, as well 
as a report summarizing each substantive public contact with FAA 
personnel concerning this proposed rulemaking. Before acting on this 
proposal, the FAA will consider all comments received by the closing 
date for comments. The FAA will consider comments filed after the 
comment period has closed if it is possible to do so without incurring 
expense or delay. The FAA may change this NPRM because of those 
comments.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to the 
person identified in the FOR FURTHER INFORMATION CONTACT section. Any 
commentary that the FAA receives which is not specifically designated 
as CBI will be placed in the public docket for this rulemaking.

Discussion

    The ANAC, which is the aviation authority for Brazil, has issued 
ANAC AD 2020-07-02, effective July 21, 2020 (``ANAC AD 2020-07-02'') 
(also referred to as the Mandatory Continuing Airworthiness 
Information, or ``the MCAI''), to correct an unsafe condition for 
certain Yabor[atilde] Ind[uacute]stria Aeron[aacute]utica S.A. Model 
EMB-135, EMB-145, -145ER, -145MR, -145LR, -145XR, -145MP, and -145EP 
airplanes. Model EMB-145EU, EMB-145LU, and EMB-145MK airplanes are not 
certificated by the FAA and are not included on the U.S. type 
certificate data sheet; this AD therefore does not include those 
airplanes in the applicability.
    This proposed AD was prompted by reports that calculations provided 
by the ATTCS do not take into consideration the required engine air 
bleed during operations with a single engine and anti-ice system on. 
The FAA is proposing this AD to address the risk of over-prediction of 
the operational margins, without the necessary alert being provided to 
the flightcrew in some situations. This condition, if not corrected, 
could lead to a performance reduction during takeoff, in which case

[[Page 75965]]

the aircraft may not be able to take off safely. See the MCAI for 
additional background information.

Related Service Information Under 1 CFR Part 51

    ANAC AD 2020-07-02 describes procedures for updating the software 
of the installed FADECs to version B9.4 or B9.4.1. This material is 
reasonably available because the interested parties have access to it 
through their normal course of business or by the means identified in 
the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
and service information referenced above. The FAA is proposing this AD 
because the FAA evaluated all the relevant information and determined 
the unsafe condition described previously is likely to exist or develop 
in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in ANAC AD 2020-07-02 described previously, as incorporated by 
reference, except for any differences identified as exceptions in the 
regulatory text of this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and the European Union 
Aviation Safety Agency (EASA) to develop a process to use certain EASA 
ADs as the primary source of information for compliance with 
requirements for corresponding FAA ADs. The FAA has since coordinated 
with other manufacturers and civil aviation authorities (CAAs) to use 
this process. As a result, ANAC AD 2020-07-02 will be incorporated by 
reference in the FAA final rule. This proposed AD would, therefore, 
require compliance with ANAC AD 2020-07-02 in its entirety, through 
that incorporation, except for any differences identified as exceptions 
in the regulatory text of this proposed AD. Service information 
specified in ANAC AD 2020-07-02 that is required for compliance with 
ANAC AD 2020-07-02 will be available on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
1035 after the FAA final rule is published.

Costs of Compliance

    The FAA estimates that this proposed AD affects 494 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
5 work-hours x $85 per hour = $425...........................              $0             $425         $209,950
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Yabor[atilde] Ind[uacute]stria Aeron[aacute]utica S.A. (Type 
Certificate Previously Held by Embraer S.A.): Docket No. FAA-2020-
1035; Project Identifier MCAI-2020-01017-T.

(a) Comments Due Date

    The FAA must receive comments by January 11, 2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Yabor[atilde] Ind[uacute]stria 
Aeron[aacute]utica S.A. Model EMB-135BJ, -135ER, -135KE, -135KL, and 
-135LR airplanes, EMB-145, -45ER, -145MR, -145LR, -145XR, -145MP, 
and -145EP, certificated in any category, as identified in 
Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD 
2020-07-02, effective July 21, 2020 (``ANAC AD 2020-07-02'').

(d) Subject

    Air Transport Association (ATA) of America Code 73, Engine fuel 
and control.

(e) Reason

    This AD was prompted by reports that calculations provided by 
the automatic takeoff thrust control system (ATTCS) are incorrect 
under certain conditions. The FAA is issuing this AD to address the 
risk of over-prediction of the operational margins,

[[Page 75966]]

without the necessary alert being provided to the flightcrew in some 
situations. This condition, if not corrected, could lead to a 
performance reduction during takeoff, in which case the airplane may 
not be able to take off safely.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, ANAC AD 2020-07-02.

(j) Exceptions to ANAC AD 2020-07-02

    (1) Where ANAC AD 2020-07-02 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Alternative method of compliance (AMOC)'' section of 
ANAC AD 2020-07-02 does not apply to this AD.

(k) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (l)(2) of 
this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or ANAC; or ANAC's 
authorized Designee. If approved by the ANAC Designee, the approval 
must include the Designee's authorized signature.

(l) Related Information

    (1) For information about ANAC AD 2020-07-02, contact National 
Civil Aviation Agency (ANAC), Aeronautical Products Certification 
Branch (GGCP), Rua Dr. Orlando Feirabend Filho, 230--Centro 
Empresarial Aquarius--Torre B--Andares 14 a 18, Parque Residencial 
Aquarius, CEP 12.246-190--S[atilde]o Jos[eacute] dos Campos--SP, 
BRAZIL, Tel: 55 (12) 3203-6600; Email: pac@anac.gov.br; internet 
www.anac.gov.br/en/. You may find this IBR material on the ANAC 
website at https://sistemas.anac.gov.br/certificacao/DA/DAE.asp. You 
may view this material at the FAA, Airworthiness Products Section, 
Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 
206-231-3195. This material may be found in the AD docket on the 
internet at https://www.regulations.gov by searching for and 
locating Docket No. FAA-2020-1035.
    (2) For more information about this AD, contact Kathleen 
Arrigotti, Aerospace Engineer, Large Aircraft Section, International 
Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; 
telephone and fax 206-231-3218; email kathleen.arrigotti@faa.gov.

    Issued on November 19, 2020.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2020-26045 Filed 11-25-20; 8:45 am]
BILLING CODE 4910-13-P


