[Federal Register Volume 85, Number 200 (Thursday, October 15, 2020)]
[Rules and Regulations]
[Pages 65200-65203]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-22763]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-0908; Project Identifier MCAI-2020-01256-T; 
Amendment 39-21282; AD 2020-21-09]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Airbus SAS Model A318 series airplanes; Model A319 series airplanes; 
Model A320 series airplanes; and Model A321 series airplanes. This AD 
was prompted by reports of cracks on the main landing gear (MLG) 
sliding tubes. This AD requires a general visual inspection of the MLG 
sliding tubes for cracks, and replacement, if necessary, as specified 
in a European Union Aviation Safety Agency (EASA) AD 2020-0193, which 
is incorporated by reference. The FAA is issuing this AD to address the 
unsafe condition on these products.

DATES: This AD becomes effective October 30, 2020.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of October 30, 
2020.
    The FAA must receive comments on this AD by November 30, 2020.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For material incorporated by reference (IBR) in this AD, contact 
the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 
221 8999 000; email: ADs@easa.europa.eu; internet: www.easa.europa.eu. 
You may find this IBR material on the EASA website at https://ad.easa.europa.eu. You may view this IBR material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195. It is also available in the AD 
docket on the internet at https://www.regulations.gov by searching for 
and locating Docket No. FAA-2020-0908.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
0908; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this AD, any comments received, and other information. The street 
address for Docket Operations is listed above. Comments will be 
available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Sanjay Ralhan, Aerospace Engineer, 
Large Aircraft Section, International Validation Branch, FAA, 2200 
South 216th St., Des Moines, WA 98198; phone and fax: 206-231-3223; 
email: sanjay.ralhan@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2020-0193, dated September 7, 2020 
(``EASA AD 2020-0193'') (also referred to as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for all Airbus SAS Model A318 series airplanes; Model A319 
series airplanes; Model A320-211, -212, -214, -215, -216, -231, -232, -
233, -251N, -252N, -253N, -271N, -272N, and -273N airplanes; and Model 
A321 series airplanes. Model A320-215 airplanes are not certificated by 
the FAA and are not included on the U.S. type certificate data sheet; 
this AD therefore does not include those airplanes in the 
applicability.
    EASA AD 2010-0193 states that it issued EASA AD 2018-0136, dated 
June

[[Page 65201]]

26, 2018 (which corresponds to FAA AD 2019-03-18, Amendment 39-19570 
(84 FR 7804, March 5, 2019)) to address a related unsafe condition for 
parts overhauled and/or repaired by specific maintenance organizations.
    This AD was prompted by reports of cracks found during second 
overhaul of two MLG on the sliding tubes. The FAA is issuing this AD to 
address cracks on the MLG sliding tubes, which could cause MLG sliding 
tube fracture, and could possibly result in the MLG collapsing, 
damaging the airplane, and injuring occupants. See the MCAI for 
additional background information.

Related IBR Material Under 1 CFR Part 51

    EASA AD 2020-0193 describes procedures for a general visual 
inspection of the MLG sliding tubes for cracks, and replacement, if 
necessary. This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this AD because the FAA evaluated 
all pertinent information and determined the unsafe condition exists 
and is likely to exist or develop on other products of the same type 
design.

Requirements of This AD

    This AD requires accomplishing the actions specified in EASA AD 
2020-0193 described previously, as incorporated by reference, except 
for any differences identified as exceptions in the regulatory text of 
this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to use this process. As a result, EASA AD 2020-0193 
is incorporated by reference in this final rule. This AD, therefore, 
requires compliance with EASA AD 2020-0193 in its entirety, through 
that incorporation, except for any differences identified as exceptions 
in the regulatory text of this AD. Using common terms that are the same 
as the heading of a particular section in the EASA AD does not mean 
that operators need comply only with that section. For example, where 
the AD requirement refers to ``all required actions and compliance 
times,'' compliance with this AD requirement is not limited to the 
section titled ``Required Action(s) and Compliance Time(s)'' in the 
EASA AD. Service information specified in EASA AD 2020-0193 that is 
required for compliance with EASA AD 2020-0193 is available on the 
internet at https://www.regulations.gov by searching for and locating 
Docket No. FAA-2020-0908.

Justification for Immediate Adoption and Determination of the Effective 
Date

    Section 553(b)(3)(B) of the Administrative Procedure Act (APA) (5 
U.S.C. 551 et seq.) authorizes agencies to dispense with notice and 
comment procedures for rules when the agency, for ``good cause,'' finds 
that those procedures are ``impracticable, unnecessary, or contrary to 
the public interest.'' Under this section, an agency, upon finding good 
cause, may issue a final rule without providing notice and seeking 
comment prior to issuance. Further, section 553(d) of the APA 
authorizes agencies to make rules effective in less than thirty days, 
upon a finding of good cause.
    An unsafe condition exists that requires the immediate adoption of 
this AD without providing an opportunity for public comments prior to 
adoption. The FAA has found that the risk to the flying public 
justifies waiving notice and comment prior to adoption of this rule 
because cracks on the MLG sliding tubes, if not detected and corrected, 
could lead to MLG sliding tube fracture, possibly resulting in MLG 
collapse with consequent damage to the airplane and injury to 
occupants. In addition, the compliance time for the required action is 
shorter than the time necessary for the public to comment and for 
publication of the final rule. Therefore this rule must be issued 
immediately, to ensure the safety of the flight crews conducting such 
flights. Accordingly, notice and opportunity for prior public comment 
are impracticable and contrary to the public interest pursuant to 5 
U.S.C. 553(b)(3)(B).
    In addition, the FAA finds that good cause exists pursuant to 5 
U.S.C. 553(d) for making this amendment effective in less than 30 days, 
for the same reasons the FAA found good cause.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety, and the FAA did not precede it by notice and opportunity for 
public comment. The FAA invites you to send any written relevant data, 
views, or arguments about this AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2020-0908; 
Project Identifier MCAI-2020-01256-T'' at the beginning of your 
comments. The most helpful comments reference a specific portion of the 
proposal, explain the reason for any recommended change, and include 
supporting data. Except for Confidential Business Information (CBI) as 
described in the following paragraph, and other information as 
described in 14 CFR 11.35, the FAA will consider all comments received 
by the closing date and may amend this AD based on those comments.
    The FAA will post all comments the FAA receives, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The FAA will also post a report summarizing each substantive 
verbal contact the FAA receives about this AD.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this AD contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this AD, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this AD. Submissions containing CBI should be sent to the 
person identified in the FOR FURTHER INFORMATION CONTACT section. Any 
commentary that the FAA receives which is not specifically designated 
as CBI will be placed in the public docket for this rulemaking.

Interim Action

    The FAA considers this AD interim action. The inspection reports 
that are required by this AD will enable the manufacturer to obtain 
better insight into the nature, cause, and extent of the cracking, and 
eventually to develop final action to address the unsafe

[[Page 65202]]

condition. Once final action has been identified, the FAA might 
consider further rulemaking.

Regulatory Flexibility Act (RFA)

    The requirements of the RFA do not apply when an agency finds good 
cause pursuant to 5 U.S.C. 553 to adopt a rule without prior notice and 
comment. Because the FAA has determined that it has good cause to adopt 
this rule without notice and comment, RFA analysis is not required.

Costs of Compliance

    The FAA estimates that this AD affects 1,630 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                     Estimated Costs for Required Actions *
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
2 work-hours x $85 per hour = $170...........................              $0             $170         $277,100
----------------------------------------------------------------------------------------------------------------
* Table does not include estimated costs for reporting.

    The FAA estimates that it takes about 1 work-hour per product to 
comply with the reporting requirement in this AD. The average labor 
rate is $85 per hour. Based on these figures, the FAA estimates the 
cost of reporting the inspection results on U.S. operators to be 
$138,550, or $85 per product.
    The FAA estimates the following costs to do any necessary on-
condition replacements that would be required based on the results of 
any required inspections. The FAA has no way of determining the number 
of aircraft that might need these on-condition replacements:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
                                                             Cost per
              Labor cost                   Parts cost        product
------------------------------------------------------------------------
6 work-hours x $85 per hour = $510....             (*)             $510
------------------------------------------------------------------------
* The FAA has received no definitive data on which to base the parts
  cost estimates for the on-condition replacements specified in this AD.

Paperwork Reduction Act

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to penalty for 
failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act unless that collection of 
information displays a current valid OMB control number. The control 
number for the collection of information required by this AD is 2120-
0056. The paperwork cost associated with this AD has been detailed in 
the Costs of Compliance section of this document and includes time for 
reviewing instructions, as well as completing and reviewing the 
collection of information. Therefore, all reporting associated with 
this AD is mandatory. Comments concerning the accuracy of this burden 
and suggestions for reducing the burden should be directed to 
Information Collection Clearance Officer, Federal Aviation 
Administration, 10101 Hillwood Parkway, Fort Worth, TX 76177-1524.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866, and
    (2) Will not affect intrastate aviation in Alaska.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2020-21-09 Airbus SAS: Amendment 39-21282; Docket No. FAA-2020-0908; 
Project Identifier MCAI-2020-01256-T.

(a) Effective Date

    This AD becomes effective October 30, 2020.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all the Airbus SAS airplanes identified in 
paragraphs (c)(1) through (4) of this AD, certificated in any 
category.

[[Page 65203]]

    (1) Model A318-111, -112, -121, and -122 airplanes.
    (2) Model A319-111, -112, -113, -114, -115, -131, -132, -133, -
151N, -153N, and -171N airplanes.
    (3) Model A320-211, -212, -214, -216, -231, -232, -233, -251N, -
252N, -253N, -271N, -272N, and -273N airplanes.
    (4) Airbus SAS Model A321-111, -112, -131, -211, -212, -213, -
231, -232, -251N, -252N, -253N, -271N, -272N, -251NX, -252NX, -
253NX, -271NX, and -272NX airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 32, Landing 
gear.

(e) Reason

    This AD was prompted by reports of cracks on the main landing 
gear (MLG) sliding tubes. The FAA is issuing this AD to address 
cracks on the MLG sliding tubes, which could cause MLG sliding tube 
fracture, and could possibly result in the MLG collapsing, damaging 
the airplane, and injuring occupants.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2020-0193, dated September 7, 2020 (``EASA 
AD 2020-0193'').

(h) Exceptions to EASA AD 2020-0193

    (1) Where EASA AD 2020-0193 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2020-0193 does not apply 
to this AD.
    (3) Paragraph (4) of EASA AD 2020-0193 specifies to report 
inspection results to Airbus within a certain compliance time. For 
this AD, report inspection results at the applicable time specified 
in paragraph (h)(3)(i) or (ii) of this AD.
    (i) If the inspection was done on or after the effective date of 
this AD: Submit the report within 15 days after the inspection.
    (ii) If the inspection was done before the effective date of 
this AD: Submit the report within 15 days after the effective date 
of this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (j) of this 
AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Airbus 
SAS's EASA Design Organization Approval (DOA). If approved by the 
DOA, the approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraphs (h)(3) and (i)(2) of this AD, if any service information 
referenced in EASA AD 2020-0193 contains paragraphs that are labeled 
as RC, the instructions in RC paragraphs, including subparagraphs 
under an RC paragraph, must be done to comply with this AD; any 
paragraphs, including subparagraphs under those paragraphs, that are 
not identified as RC are recommended. The instructions in 
paragraphs, including subparagraphs under those paragraphs, not 
identified as RC may be deviated from using accepted methods in 
accordance with the operator's maintenance or inspection program 
without obtaining approval of an AMOC, provided the instructions 
identified as RC can be done and the airplane can be put back in an 
airworthy condition. Any substitutions or changes to instructions 
identified as RC require approval of an AMOC.
    (4) Paperwork Reduction Act Burden Statement: A federal agency 
may not conduct or sponsor, and a person is not required to respond 
to, nor shall a person be subject to a penalty for failure to comply 
with a collection of information subject to the requirements of the 
Paperwork Reduction Act unless that collection of information 
displays a current valid OMB Control Number. The OMB Control Number 
for this information collection is 2120-0056. Public reporting for 
this collection of information is estimated to be approximately 1 
hour per response, including the time for reviewing instructions, 
searching existing data sources, gathering and maintaining the data 
needed, and completing and reviewing the collection of information. 
All responses to this collection of information are mandatory as 
required by this AD. Send comments regarding this burden estimate or 
any other aspect of this collection of information, including 
suggestions for reducing this burden to Information Collection 
Clearance Officer, Federal Aviation Administration, 10101 Hillwood 
Parkway, Fort Worth, TX 76177-1524.

(j) Related Information

    For more information about this AD, contact Sanjay Ralhan, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; phone and 
fax: 206-231-3223; email: sanjay.ralhan@faa.gov.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2020-0193, 
dated September 7, 2020.
    (ii) [Reserved]
    (3) For EASA AD 2020-0193, contact the EASA, Konrad-Adenauer-
Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email 
ADs@easa.europa.eu; internet www.easa.europa.eu. You may find this 
EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195. This material may be found in the AD 
docket on the internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2020-0908.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
fedreg.legal@nara.gov, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on October 1, 2020.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2020-22763 Filed 10-14-20; 8:45 am]
BILLING CODE 4910-13-P


