[Federal Register Volume 85, Number 143 (Friday, July 24, 2020)]
[Proposed Rules]
[Pages 44798-44800]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-16042]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-0729; Project Identifier AD-2020-00620-E]
RIN 2120-AA64


Airworthiness Directives; CFM International, S.A. Turbofan 
Engines

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain CFM International, S.A. (CFM) LEAP-1A23, LEAP-1A24, LEAP-
1A24E1, LEAP-1A26, LEAP-1A26CJ, LEAP-1A26E1, LEAP-1A29, LEAP-1A29CJ, 
LEAP-1A30, LEAP-1A32, LEAP-1A33, LEAP-1A33B2, LEAP-1A35A model turbofan 
engines. This proposed AD was prompted by an investigation by CFM that 
showed a subsurface anomaly in a part manufactured using the same 
material as the LEAP-1A high-pressure turbine (HPT) stage 2 disk. This 
proposed AD would require an ultrasonic inspection (UI) of the HPT 
stage 2 disk and replacement of any HPT stage 2 disk that fails the UI 
with a part eligible for installation. The FAA is proposing this AD to 
address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by September 
8, 2020.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:

[[Page 44799]]

     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact CFM 
International, S.A., Aviation Operations Center, 1 Neumann Way, M/D 
Room 285, Cincinnati, OH 45125, United States; phone: (877) 432-3272; 
email: fleetsupport@ge.com. You may view this service information at 
the FAA, Airworthiness Products Section, Operational Safety Branch, 
1200 District Avenue, Burlington, MA 01803. For information on the 
availability of this material at the FAA, call 781-238-7759.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
0729; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, any comments received, and other information. The street 
address for Docket Operations is listed above. Comments will be 
available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Christopher McGuire, Aerospace 
Engineer, ECO Branch, FAA, 1200 District Avenue, Burlington, MA 01803; 
phone: (781) 238-7120; fax: (781) 238-7199; email: 
Chris.McGuire@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2020-0729; 
Project Identifier AD-2020-00620-E'' at the beginning of your comments. 
The most helpful comments reference a specific portion of the proposal, 
explain the reason for any recommended change, and include supporting 
data. The FAA will consider all comments received by the closing date 
and may amend this NPRM because of those comments.
    Except for Confidential Business Information as described in the 
following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The FAA will also post a report summarizing each substantive 
verbal contact received about this proposal.

Confidential Business Information

    Confidential Business Information (CBI) is commercial or financial 
information that is both customarily and actually treated as private by 
its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), 
CBI is exempt from public disclosure. If your comments responsive to 
this NPRM contain commercial or financial information that is 
customarily treated as private, that you actually treat as private, and 
that is relevant or responsive to this NPRM, it is important that you 
clearly designate the submitted comments as CBI. Please mark each page 
of your submission containing CBI as ``PROPIN.'' The FAA will treat 
such marked submissions as confidential under the FOIA, and they will 
not be placed in the public docket of this NPRM. Submissions containing 
CBI should be sent to Christopher McGuire, Aerospace Engineer, ECO 
Branch, FAA, 1200 District Avenue, Burlington, MA, 01803. Any 
commentary that the FAA receives which is not specifically designated 
as CBI will be placed in the public docket for this rulemaking.

Background

    The FAA learned that during a broad investigation by CFM into melt-
related material anomalies, a subsurface anomaly was found in a part 
manufactured from the same material used to manufacture the LEAP-1A HPT 
stage 2 disk. This condition, if not addressed, could result in failure 
of the HPT stage 2 disk, uncontained release of the HPT stage 2 disk, 
damage to the engine, and damage to the airplane.

FAA's Determination

    The FAA is issuing this NPRM because the agency has determined that 
the unsafe condition described previously is likely to exist or develop 
in other products of the same type design.

Service Information Incorporated by Reference Under 1 CFR Part 51

    The FAA reviewed CFM Service Bulletin (SB) LEAP-1A-72-00-0405-01A-
930A-D, Issue 001, dated March 5, 2020. The SB describes procedures for 
performing an ultrasonic inspection of the HPT stage 2 disk. This 
service information is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

Proposed AD Requirements

    This proposed AD would require a UI of the HPT stage 2 disk and 
replacement of any HPT stage 2 disk that fails the inspection with a 
part eligible for installation.

Costs of Compliance

    The FAA estimates that this AD, as proposed, would affect 148 
engines installed on airplanes of U.S. registry.
    The FAA estimates the following costs to comply with this proposed 
AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
               Action                         Labor cost            Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
UI of HPT stage 2 disk.............  8 work-hours x $85 per hour              $0            $680        $100,640
                                      = $680.
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary 
replacements that would be required based on the results of the 
proposed inspection. The FAA has no way of determining the number of 
aircraft that might need these replacements:

[[Page 44800]]



                                               On-Condition Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                   Action                                 Labor cost                Parts cost        product
----------------------------------------------------------------------------------------------------------------
Replace HPT stage 2 disk...................  0.25 work-hours x $85.00 per hour =        $286,000     $286,021.25
                                              $21.25.
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

CFM International, S.A.: Docket No. FAA-2020-0729; Project 
Identifier AD-2020-00620-E.

(a) Comments Due Date

    The FAA must receive comments by September 8, 2020.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to CFM International, S.A. (CFM) LEAP-1A23, 
LEAP-1A24, LEAP-1A24E1, LEAP-1A26, LEAP-1A26CJ, LEAP-1A26E1, LEAP-
1A29, LEAP-1A29CJ, LEAP-1A30, LEAP-1A32, LEAP-1A33, LEAP-1A33B2, 
LEAP-1A35A model turbofan engines with a high-pressure turbine (HPT) 
stage 2 disk, part number (P/N) 2466M52G03 or P/N 2788M26G01 
installed, and with a serial number listed in Table 1 of CFM Service 
Bulletin (SB) LEAP-1A-72-00-0405-01A-930A-D, Issue 001, dated March 
5, 2020.

(d) Subject

    Joint Aircraft System Component (JASC) Code 7250, Turbine 
Section.

(e) Unsafe Condition

    This AD was prompted by an investigation by CFM that discovered 
a subsurface anomaly in a part manufactured from the same material 
as used to manufacture the LEAP-1A HPT stage 2 disk. The FAA is 
issuing this AD to prevent failure of the LEAP-1A HPT stage 2 disk. 
The unsafe condition, if not addressed, could result in uncontained 
release of the HPT stage 2 disk, damage to the engine, and damage to 
the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    (1) At next piece part exposure after the effective date of this 
AD, perform an ultrasonic inspection of the HPT stage 2 disk in 
accordance with the Accomplishment Instructions, paragraph 5.A.(1), 
of CFM SB LEAP-1A-72-00-0405-01A-930A-D, Issue 001, dated March 5, 
2020.
    (2) Replace any disk that fails the inspection required by 
paragraph (g)(1) of this AD with a part eligible for installation.

(h) Definition

    For the purpose of this AD, a part eligible for installation is 
a HPT stage 2 disk not affected by this AD, or an HPT stage 2 disk 
that has been inspected in accordance with the Accomplishment 
Instructions, paragraph 5.A.(1), of CFM SB LEAP-1A-72-00-0405-01A-
930A-D, Issue 001, dated March 5, 2020, and is not rejected by the 
inspection limits as specified in the service information.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, ECO Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or local Flight Standards District Office, as 
appropriate. If sending information directly to the manager of the 
certification office, send it to the attention of the person 
identified in paragraph (j)(1) of this AD. You may email your 
request to: ANE-AD-AMOC@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.

(j) Related Information

    (1) For more information about this AD, contact Christopher 
McGuire, Aerospace Engineer, ECO Branch, FAA, 1200 District Avenue, 
Burlington, MA 01803; phone: (781) 238-7120; fax: (781) 238-7199; 
email: Chris.McGuire@faa.gov.
    (2) For service information identified in this AD, contact CFM 
International, S.A., Aviation Operations Center, 1 Neumann Way, M/D 
Room 285, Cincinnati, OH 45125, United States; phone: (877) 432-
3272; email: fleetsupport@ge.com. You may view this referenced 
service information at the FAA, Airworthiness Products Section, 
Operational Safety Branch, 1200 District Avenue, Burlington, MA, 
01803. For information on the availability of this material at the 
FAA, call 781-238-7759.

    Issued on July 21, 2020.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2020-16042 Filed 7-23-20; 8:45 am]
BILLING CODE 4910-13-P


