[Federal Register Volume 85, Number 82 (Tuesday, April 28, 2020)]
[Rules and Regulations]
[Pages 23452-23454]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-08930]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-0095; Product Identifier 2019-NM-192-AD; Amendment 
39-19904; AD 2020-08-12]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain The Boeing Company Model 747-8 and 747-8F series airplanes. 
This AD was prompted by an evaluation by the design approval holder 
(DAH) indicating that the skin lap joints at certain stringers are 
subject to widespread fatigue damage (WFD). This AD requires modifying 
the left and right side lap joints of the fuselage skin, repetitive 
post-modification inspections for cracking, and applicable on-condition 
actions. The FAA is issuing this AD to address the unsafe condition on 
these products.

DATES: This AD is effective June 2, 2020.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of June 2, 
2020.

ADDRESSES: For service information identified in this final rule, 
contact Boeing Commercial Airplanes, Attention: Contractual & Data 
Services (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 
90740-5600; telephone 562-797-1717; internet https://www.myboeingfleet.com. You may view this service information at the 
FAA, Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability of 
this material at the FAA, call 206-231-3195. It is also available on 
the internet at https://www.regulations.gov by searching for and 
locating Docket No. FAA-2020-0095.

Examining the AD Docket

    You may examine the AD docket on the internet at https://

[[Page 23453]]

www.regulations.gov by searching for and locating Docket No. FAA-2020-
0095; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Bill Ashforth, Senior Aerospace 
Engineer, Airframe Section, FAA, Seattle ACO Branch, 2200 South 216th 
St., Des Moines, WA 98198; phone and fax: 206-231-3520; email: 
bill.ashforth@faa.gov.

SUPPLEMENTARY INFORMATION: 

Discussion

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to certain The Boeing 
Company Model 747-8 and 747-8F series airplanes. The NPRM published in 
the Federal Register on February 13, 2020 (85 FR 8207). The NPRM was 
prompted by an evaluation by the DAH indicating that the skin lap 
joints at certain stringers are subject to WFD. The NPRM proposed to 
require modifying the left and right side lap joints of the fuselage 
skin, repetitive post-modification inspections for cracking, and 
applicable on-condition actions.
    The FAA is issuing this AD to address undetected fatigue cracks, 
which could result in sudden decompression and reduced structural 
integrity of the airplane.

Comments

    The FAA gave the public the opportunity to participate in 
developing this final rule. The FAA has considered the comment 
received. Boeing indicated its support for the NPRM.

Conclusion

    The FAA reviewed the relevant data, considered the comment 
received, and determined that air safety and the public interest 
require adopting this final rule as proposed, except for minor 
editorial changes. The FAA has determined that these minor changes:
     Are consistent with the intent that was proposed in the 
NPRM for addressing the unsafe condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Boeing Alert Requirements Bulletin 747-53A2895 RB, 
dated September 12, 2019. This service information describes procedures 
for modifying the left and right side lap joints of the fuselage skin, 
repetitive post-modification internal detailed and surface high 
frequency eddy current (HFEC) inspections for cracking, and applicable 
on-condition actions. On-condition actions include repair. This service 
information is reasonably available because the interested parties have 
access to it through their normal course of business or by the means 
identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 14 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                     Estimated Costs for Required Actions *
----------------------------------------------------------------------------------------------------------------
                                                                                                 Cost on U.S.
              Action                    Labor cost        Parts cost      Cost per product        operators
----------------------------------------------------------------------------------------------------------------
Modification of S-6 and S-23.....  1,856 work-hours x              (*)  $157,760...........  $2,208,640.
                                    $85 per hour =
                                    $157,760.
Post-mod inspection of S[dash]6    68 work-hours x $85              $0  $5,780 per           $80,920 per
 and S-23.                          per hour = $5,780                    inspection cycle.    inspection cycle.
                                    per inspection
                                    cycle.
Modification of S-44.............  1,216 work-hours x              (*)  $103,360...........  $1,447,040.
                                    $85 per hour =
                                    $103,360.
Post-mod inspection of S[dash]44.  28 work-hours x $85              $0  $2,380 per           $33,320 per
                                    per hour = $2,380                    inspection cycle.    inspection cycle.
                                    per inspection
                                    cycle.
----------------------------------------------------------------------------------------------------------------
* The FAA has received no definitive data that would enable the agency to provide parts cost estimates for the
  modifications specified in this AD.

    The FAA has received no definitive data that would enable the 
agency to provide cost estimates for the on-condition actions specified 
in this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

[[Page 23454]]

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2020-08-12 The Boeing Company: Amendment 39-19904; Docket No. FAA-
2020-0095; Product Identifier 2019-NM-192-AD.

(a) Effective Date

    This AD is effective June 2, 2020.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 747-8 and 747-8F 
series airplanes, certificated in any category, as identified in 
Boeing Alert Requirements Bulletin 747-53A2895 RB, dated September 
12, 2019.

(d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Unsafe Condition

    This AD was prompted by an evaluation by the design approval 
holder (DAH) indicating that the skin lap joints at certain 
stringers are subject to widespread fatigue damage (WFD). The FAA is 
issuing this AD to address undetected fatigue cracks, which could 
result in sudden decompression and reduced structural integrity of 
the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as specified by paragraph (h) of this AD: At the 
applicable times specified in the ``Compliance'' paragraph of Boeing 
Alert Requirements Bulletin 747-53A2895 RB, dated September 12, 
2019, do all applicable actions identified in, and in accordance 
with, the Accomplishment Instructions of Boeing Alert Requirements 
Bulletin 747-53A2895 RB, dated September 12, 2019.
    Note 1 to paragraph (g): Guidance for accomplishing the actions 
required by this AD can be found in Boeing Alert Service Bulletin 
747-53A2895, dated September 12, 2019, which is referred to in 
Boeing Alert Requirements Bulletin 747-53A2895 RB, dated September 
12, 2019.

(h) Exception to Service Information Specifications

    Where Boeing Alert Requirements Bulletin 747-53A2895 RB, dated 
September 12, 2019, specifies contacting Boeing for repair 
instructions: This AD requires doing the repair before further 
flight using a method approved in accordance with the procedures 
specified in paragraph (i) of this AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO Branch, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or local Flight Standards District 
Office, as appropriate. If sending information directly to the 
manager of the certification office, send it to the attention of the 
person identified in paragraph (j)(1) of this AD. Information may be 
emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by The Boeing Company Organization Designation 
Authorization (ODA) that has been authorized by the Manager, Seattle 
ACO Branch, FAA, to make those findings. To be approved, the repair 
method, modification deviation, or alteration deviation must meet 
the certification basis of the airplane, and the approval must 
specifically refer to this AD.

(j) Related Information

    (1) For more information about this AD, contact Bill Ashforth, 
Senior Aerospace Engineer, Airframe Section, FAA, Seattle ACO 
Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 
206-231-3520; email: bill.ashforth@faa.gov.
    (2) Service information identified in this AD that is not 
incorporated by reference is available at the addresses specified in 
paragraphs (k)(3) and (4) of this AD.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Boeing Alert Requirements Bulletin 747-53A2895 RB, dated 
September 12, 2019.
    (ii) [Reserved]
    (3) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; internet https://www.myboeingfleet.com.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, email fedreg.legal@nara.gov, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on April 20, 2020.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2020-08930 Filed 4-27-20; 8:45 am]
 BILLING CODE 4910-13-P


