[Federal Register Volume 84, Number 239 (Thursday, December 12, 2019)]
[Rules and Regulations]
[Pages 67834-67837]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-26704]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0973; Product Identifier 2019-NM-187-AD; Amendment 
39-19811; AD 2019-23-17]
RIN 2120-AA64


Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Dassault Aviation Model FALCON 900EX and Model FALCON 2000EX 
airplanes. This AD was prompted by reports of iced angle-of-attack 
(AoA) probes after take-off, with associated misleading airspeed 
indication and/or misleading stall warning. This AD requires revising 
the existing airplane flight manual (AFM) to provide the flightcrew 
with updated procedures related to manually activating heating of the 
AoA probes during line up, as specified in a European Union Aviation 
Safety Agency (EASA) AD, which is incorporated by reference. The FAA is 
issuing this AD to address the unsafe condition on these products.

DATES: This AD becomes effective December 27, 2019.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of December 27, 
2019.
    We must receive comments on this AD by January 27, 2020.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:

[[Page 67835]]

     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For the material incorporated by reference (IBR) in this AD, 
contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 89990 1000; email ADs@easa.europa.eu; internet 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at https://ad.easa.europa.eu. You may view this IBR material at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. 
For information on the availability of this material at the FAA, call 
206-231-3195. It is also available in the AD docket on the internet at 
https://www.regulations.gov by searching for and locating Docket No. 
FAA-2019-0973.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0973; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this AD, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations is listed above. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3226.

SUPPLEMENTARY INFORMATION: 

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2019-0273, dated November 4, 2019 
(``EASA AD 2019-0273'') (also referred to as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for certain Model FALCON 900EX and FALCON 2000EX airplanes.
    This AD was prompted by reports of iced AoA probes after take-off, 
with associated misleading airspeed indication and/or misleading stall 
warning. A slow or late positioning of thrust levers into the take-off 
position in certain conditions can lead to probes being heated too late 
during the take-off run, which increases the risk of icing on probes 
after take-off. The FAA is issuing this AD to address this condition, 
which could lead to blocked AoA probes, possibly resulting in reduced 
control of the airplane. See the MCAI for additional background 
information.

Related IBR Material Under 1 CFR Part 51

    EASA AD 2019-0273 describes procedures for revising the existing 
AFM to provide the flightcrew with updated normal procedures related to 
manually activating AoA probe heating during line up. This material is 
reasonably available because the interested parties have access to it 
through their normal course of business or by the means identified in 
the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to a bilateral agreement with the State of Design Authority, the FAA 
has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this AD because the agency 
evaluated all pertinent information and determined the unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Requirements of This AD

    This AD requires accomplishing the actions specified in EASA AD 
2019-0273 described previously, as incorporated by reference, except 
for any differences identified as exceptions in the regulatory text of 
this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to use this process. As a result, EASA AD 2019-0273 
will be incorporated by reference in the FAA final rule. This AD, 
therefore, requires compliance with EASA AD 2019-0273 in its entirety, 
through that incorporation, except for any differences identified as 
exceptions in the regulatory text of this AD. Using common terms that 
are the same as the heading of a particular section in the EASA AD does 
not mean that operators need comply only with that section. For 
example, where the AD requirement refers to ``all required actions and 
compliance times,'' compliance with this AD requirement is not limited 
to the section titled ``Required Action(s) and Compliance Time(s)'' in 
the EASA AD. Service information specified in EASA AD 2019-0273 that is 
required for compliance with EASA AD 2019-0273 will be available on the 
internet at https://www.regulations.gov by searching for and locating 
Docket No. FAA-2019-0973 after the FAA final rule is published.

FAA's Justification and Determination of the Effective Date

    An unsafe condition exists that requires the immediate adoption of 
this AD without providing an opportunity for public comments prior to 
adoption. The FAA has found that the risk to the flying public 
justifies waiving notice and comment prior to adoption of this rule 
because these airplanes are subject to reduced efficiency of the AoA 
protections that may result in iced AoA probes after take-off, with 
associated misleading airspeed indication and/or misleading stall 
warning. A slow or late positioning of thrust levers into the take-off 
position in certain conditions can lead to probes being heated too late 
during the take-off run, which increases the risk of icing on probes 
after take-off. This condition could result in blocked AoA probes, 
which could possibly result in reduced control of the airplane. 
Therefore, we find good cause that notice and opportunity for prior 
public comment are impracticable. In addition, for the reasons stated 
above, we find that good cause exists for making this amendment 
effective in less than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety, and the FAA did not precede it by notice and opportunity for 
public comment. The FAA invites you to send any written relevant data, 
views, or arguments about this AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2019-0973; 
Product Identifier 2019-NM-187-AD'' at the beginning of your comments. 
The FAA specifically invites comments on the overall

[[Page 67836]]

regulatory, economic, environmental, and energy aspects of this AD. The 
FAA will consider all comments received by the closing date and may 
amend this AD based on those comments.
    The FAA will post all comments received, without change, to https://www.regulations.gov, including any personal information you provide. 
The FAA will also post a report summarizing each substantive verbal 
contact received about this AD.

Regulatory Flexibility Act

    The requirements of the Regulatory Flexibility Act (RFA) do not 
apply when an agency finds good cause pursuant to 5 U.S.C. 553 to adopt 
a rule without prior notice and comment. Because the FAA has determined 
that it has good cause to adopt this rule without notice and comment, 
RFA analysis is not required.

Costs of Compliance

    The FAA estimates that this AD affects 146 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
1 work-hour x $85 per hour = $85.............................              $0              $85          $12,410
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This AD is issued in accordance with authority delegated by the 
Executive Director, Aircraft Certification Service, as authorized by 
FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the Compliance and Airworthiness Division, but 
during this transition period, the Executive Director has delegated the 
authority to issue ADs applicable to transport category airplanes and 
associated appliances to the Director of the System Oversight Division.

Regulatory Findings

    The FAA determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866, and
    (2) Will not affect intrastate aviation in Alaska.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2019-23-17 Dassault Aviation: Amendment 39-19811; Docket No. FAA-
2019-0973; Product Identifier 2019-NM-187-AD.

(a) Effective Date

    This AD becomes effective December 27, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Dassault Aviation Model FALCON 900EX and 
Model FALCON 2000EX airplanes, certificated in any category, as 
identified in European Union Aviation Safety Agency (EASA) AD 2019-
0273, dated November 4, 2019 (``EASA AD 2019-0273'').

(d) Subject

    Air Transport Association (ATA) of America Code 27, Flight 
controls.

(e) Reason

    This AD was prompted by reports of iced angle-of-attack (AoA) 
probes after take-off, with associated misleading airspeed 
indication and/or misleading stall warning. A slow or late 
positioning of thrust levers into the take-off position in certain 
conditions can lead to probes being heated too late during the take-
off run, which increases the risk of icing on probes after take-off. 
The FAA is issuing this AD to address this condition, which could 
result in blocked AoA probes, possibly resulting in reduced control 
of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2019-0273.

(h) Exceptions to EASA AD 2019-0273

    (1) Where EASA AD 2019-0273 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2019-0273 does not apply 
to this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (j) of this AD. Information may 
be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager

[[Page 67837]]

of the local flight standards district office/certificate holding 
district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or EASA; or Dassault 
Aviation's EASA Design Organization Approval (DOA). If approved by 
the DOA, the approval must include the DOA-authorized signature.

(j) Related Information

    For more information about this AD, contact Tom Rodriguez, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3226.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2019-0273, 
dated November 4, 2019.
    (ii) [Reserved]
    (3) For information about EASA AD 2019-0273, contact the EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
89990 6017; email ADs@easa.europa.eu; Internet www.easa.europa.eu. 
You may find this EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this material at the FAA, Transport Standards 
Branch, 2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195. This 
material may be found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2019-0973.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
fedreg.legal@nara.gov, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Des Moines, Washington, on November 21, 2019.
Dorr Anderson,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-26704 Filed 12-11-19; 8:45 am]
 BILLING CODE 4910-13-P


