[Federal Register Volume 84, Number 222 (Monday, November 18, 2019)]
[Proposed Rules]
[Pages 63585-63588]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-24707]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0868; Product Identifier 2019-NM-152-AD]
RIN 2120-AA64


Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Dassault Aviation Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, 
and 20-F5 airplanes. This proposed AD was prompted by a determination 
that new or more restrictive airworthiness limitations are necessary. 
This proposed AD would require revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations. The FAA is

[[Page 63586]]

proposing this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by January 2, 
2020.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Dassault 
Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South 
Hackensack, NJ 07606; telephone 201-440-6700; internet https://www.dassaultfalcon.com. You may view this service information at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. 
For information on the availability of this material at the FAA, call 
206-231-3195.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0868; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations is listed above. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3226.

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2019-0868; 
Product Identifier 2019-NM-152-AD'' at the beginning of your comments. 
The FAA specifically invites comments on the overall regulatory, 
economic, environmental, and energy aspects of this NPRM. The FAA will 
consider all comments received by the closing date and may amend this 
NPRM because of those comments.
    The FAA will post all comments the agency receives, without change, 
to https://www.regulations.gov, including any personal information you 
provide. The FAA will also post a report summarizing each substantive 
verbal contact the agency receives about this NPRM.

Discussion

    The European Union Aviation Safety Agency (EASA), which is the 
Technical Agent for the Member States of the European Union, has issued 
EASA AD 2019-0200R1, dated August 29, 2019 (referred to after this as 
the Mandatory Continuing Airworthiness Information, or ``the MCAI''), 
to correct an unsafe condition for Dassault Aviation Model MYSTERE-
FALCON 20-C5, 20-D5, 20-E5, and 20-F5 airplanes, except those on which 
the Supplemental Structural Inspection Program (SSIP) (Dassault Service 
Bulletin 730) has been embodied into the airplane's maintenance 
program. You may examine the MCAI in the AD docket on the internet at 
https://www.regulations.gov by searching for and locating Docket No. 
FAA-2019-0868.
    This proposed AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary relating to safe 
life limits and certification maintenance requirements. The FAA is 
proposing this AD to address fatigue cracking, damage, and corrosion in 
principal structural elements, which could result in reduced structural 
integrity of the airplane. See the MCAI for additional background 
information.

Relationship Between Proposed AD and AD 2010-26-05

    This NPRM does not propose to supersede AD 2010-26-05 Amendment 39-
16544 (75 FR 79952, December 21, 2010) (``AD 2010-26-05''). Rather, the 
FAA has determined that a stand-alone AD is more appropriate to address 
the changes in the MCAI. This proposed AD would require revising the 
existing maintenance or inspection program, as applicable, to 
incorporate new or more restrictive airworthiness limitations. 
Accomplishment of the proposed actions would then terminate paragraph 
(g)(1) of AD 2010-26-05 only for Model MYSTERE-FALCON 20-C5, 20-D5, 20-
E5, and 20-F5 airplanes on which the SSIP has not been embodied into 
the airplane's existing maintenance or inspection program.

Related Service Information Under 1 CFR Part 51

    Dassault Aviation has issued Chapter 5-40-00, Airworthiness 
Limitations, of the Dassault Falcon 20 Retrofit 731 Maintenance Manual, 
Revision 13, dated January 1, 2019. This service information describes 
airworthiness limitations for safe life limits and certification 
maintenance requirements. This service information is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in the 
ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
and service information referenced above. The FAA is proposing this AD 
because the FAA evaluated all the relevant information and determined 
the unsafe condition described previously is likely to exist or develop 
on other products of the same type design.

Proposed Requirements of This NPRM

    This proposed AD would require revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations.
    This proposed AD would require revisions to certain operator 
maintenance documents to include new actions (e.g., inspections). 
Compliance with these actions is required by 14 CFR 91.403(c). For 
airplanes that have been previously modified, altered, or repaired in 
the areas addressed by this proposed AD, the operator may not be able 
to accomplish the actions described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must request 
approval for an alternative method of compliance according to paragraph 
(j)(1) of this proposed AD.

Costs of Compliance

    The FAA estimates that this proposed AD affects 56 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:
    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although the FAA recognizes that this number may vary from operator to 
operator. In the past, the FAA has estimated that this action takes 1 
work-hour per airplane. Since operators incorporate maintenance or

[[Page 63587]]

inspection program changes for their affected fleet(s), the FAA has 
determined that a per-operator estimate is more accurate than a per-
airplane estimate. Therefore, the FAA estimates the total cost per 
operator to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes and associated appliances to the 
Director of the System Oversight Division.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Dassault Aviation: Docket No. FAA-2019-0868; Product Identifier 
2019-NM-152-AD.

(a) Comments Due Date

    The FAA must receive comments by January 2, 2020.

(b) Affected ADs

    This AD affects AD 2010-26-05, Amendment 39-16544 (75 FR 79952, 
December 21, 2010) (``AD 2010-26-05'').

(c) Applicability

    This AD applies to Dassault Aviation Model MYSTERE-FALCON 20-C5, 
20-D5, 20-E5, and 20-F5 airplanes, certificated in any category, 
except those on which the Supplemental Structural Inspection Program 
(SSIP) (Dassault Service Bulletin 730) has been embodied into the 
airplane's existing maintenance or inspection program.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Reason

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
issuing this AD to address fatigue cracking, damage, and corrosion 
in principal structural elements, which could result in reduced 
structural integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Maintenance or Inspection Program Revision

    Within 90 days after the effective date of this AD, revise the 
existing maintenance or inspection program, as applicable, to 
incorporate the information specified in Chapter 5-40-00, 
Airworthiness Limitations, of the Dassault Falcon 20 Retrofit 731 
Maintenance Manual, Revision 13, dated January 1, 2019. The initial 
compliance time for doing the tasks is at the time specified in 
Chapter 5-40-00, Airworthiness Limitations, of the Dassault Falcon 
20 Retrofit 731 Maintenance Manual, Revision 13, dated January 1, 
2019, or within 90 days after the effective date of this AD, 
whichever occurs later.

(h) No Alternative Actions or Intervals

    After the existing maintenance or inspection program has been 
revised as required by paragraph (g) of this AD, no alternative 
actions (e.g., inspections) or intervals may be used unless the 
actions or intervals are approved as an alternative method of 
compliance (AMOC) in accordance with the procedures specified in 
paragraph (j)(1) of this AD.

(i) Terminating Action for AD 2010-26-05

    Accomplishing the actions required by this AD terminates the 
requirements of paragraph (g)(1) of AD 2010-26-05 only for Model 
MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20-F5 airplanes on which the 
SSIP has not been embodied into the airplane's existing maintenance 
or inspection program.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (k)(2) of this AD. Information 
may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or the European Union 
Aviation Safety Agency (EASA); or Dassault Aviation's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.

(k) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) EASA AD 2019-0200R1, dated August 29, 2019, for related 
information. This MCAI may be found in the AD docket on the internet 
at https://www.regulations.gov by searching for and locating Docket 
No. FAA-2019-0868.
    (2) For more information about this AD, contact Tom Rodriguez, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3226.

[[Page 63588]]

    (3) For service information identified in this AD, contact 
Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, 
South Hackensack, NJ 07606; telephone 201-440-6700; internet https://www.dassaultfalcon.com. You may view this service information at 
the FAA, Transport Standards Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at 
the FAA, call 206-231-3195.

    Issued in Des Moines, Washington, on November 6, 2019.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-24707 Filed 11-15-19; 8:45 am]
 BILLING CODE 4910-13-P


