[Federal Register Volume 84, Number 208 (Monday, October 28, 2019)]
[Proposed Rules]
[Pages 57663-57666]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-23394]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0722; Product Identifier 2019-NM-141-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for all Airbus SAS Model A300 series airplanes. This proposed AD was 
prompted by a report that bleed and air conditioning systems were 
contaminated by hydraulic fluid, and an investigation revealed that 
hydraulic fluid contaminations caused the failure of check valves 
installed on the hydraulic reservoir air pressurization system. This 
proposed AD would require repetitive functional tests of the hydraulic 
reservoir air pressurization lines and repair or replacement, if 
necessary, as specified in a European Union Aviation Safety Agency 
(EASA) AD, which will be incorporated by reference. The FAA is 
proposing this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by December 
12, 2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For the material identified in this proposed AD that will be 
incorporated by reference (IBR), contact the EASA, Konrad-Adenauer-Ufer 
3, 50668 Cologne, Germany; telephone +49 221 89990 1000; email 
ADs@easa.europa.eu; internet www.easa.europa.eu. You may find this IBR 
material on the EASA website at https://ad.easa.europa.eu. You may view 
this IBR material at the FAA, Transport Standards Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195. It is also available in the AD 
docket on the internet at http://www.regulations.gov by searching for 
and locating Docket No. FAA-2019-0722.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0722; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations is listed above. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3225.

[[Page 57664]]


SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2019-0722; 
Product Identifier 2019-NM-141-AD'' at the beginning of your comments. 
The FAA specifically invites comments on the overall regulatory, 
economic, environmental, and energy aspects of this NPRM. The FAA will 
consider all comments received by the closing date and may amend this 
NPRM based on those comments.
    The FAA will post all comments received, without change, to http://www.regulations.gov, including any personal information you provide. 
The FAA will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2019-0190, dated July 31, 2019 
(``EASA AD 2019-0190'') (also referred to as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for all Airbus SAS Model A300 series airplanes.
    This proposed AD was prompted by a report that bleed and air 
conditioning systems on an Airbus SAS Model A300-600 series airplane 
were contaminated by hydraulic fluid, and an investigation revealed 
that hydraulic fluid contaminations caused the failure of check valves 
installed on the hydraulic reservoir air pressurization system. The 
bleed and air conditioning systems on Model A300 series airplanes are 
similar in design to the model on which the event occurred. Therefore, 
Model A300 series airplanes are subject to the same unsafe condition. 
The FAA is proposing this AD to address this condition, which, if not 
detected and corrected, could lead to leakage of pressurization check 
valves, and, in case of pressurization line rupture, to loss of a 
hydraulic system, possibly resulting in reduced control of the 
airplane. See the MCAI for additional background information.
    EASA also issued AD 2019-0188, dated July 31, 2019, to address the 
identified unsafe condition for Airbus SAS Model A300-600 series 
airplane. The FAA is considering further rulemaking to correspond with 
EASA 2019-0188, dated July 31, 2019.

Related IBR Material Under 1 CFR Part 51

    EASA AD 2019-0190 describes procedures for repetitive functional 
tests of the hydraulic reservoir air pressurization lines and repair or 
replacement, if necessary.
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, the FAA 
has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is proposing this AD because the agency 
evaluated all the relevant information and determined the unsafe 
condition described previously is likely to exist or develop in other 
products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2019-0190 described previously, as incorporated by 
reference, except for any differences identified as exceptions in the 
regulatory text of this AD. This proposed AD also would require sending 
the inspection results to Airbus.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to use this process. As a result, EASA AD 2019-0190 
will be incorporated by reference in the FAA final rule. This proposed 
AD would therefore require compliance with EASA AD 2019-0190 in its 
entirety, through that incorporation, except for any differences 
identified as exceptions in the regulatory text of this proposed AD. 
Using common terms that are the same as the heading of a particular 
section in the EASA AD does not mean that operators need comply only 
with that section. For example, where the AD requirement refers to 
``all required actions and compliance times,'' compliance with this AD 
requirement is not limited to the section titled ``Required Action(s) 
and Compliance Time(s)'' in the EASA AD. Service information specified 
in EASA AD 2019-0190 that is required for compliance with EASA AD 2019-
0190 will be available on the internet at http://www.regulations.gov by 
searching for and locating Docket No. FAA-2019-0722 after the FAA final 
rule is published.

Costs of Compliance

    The FAA estimates that this proposed AD affects 1 airplane of U.S. 
registry. The FAA estimates the following costs to comply with this 
proposed AD:

                                     Estimated Costs for Required Actions *
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
2 work-hours x $85 per hour = $170...........................              $0             $170             $170
----------------------------------------------------------------------------------------------------------------
* Table does not include estimated costs for reporting.

    The FAA estimates that it would take about 1 work-hour per product 
to comply with the proposed reporting requirement in this proposed AD. 
The average labor rate is $85 per hour. Based on these figures, the FAA 
estimates the cost of reporting the inspection results on U.S. 
operators to be $85.
    The FAA estimates the following costs to do any necessary on-
condition actions that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need these on-condition actions:

[[Page 57665]]



                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
                                                             Cost per
              Labor cost                   Parts cost        product
------------------------------------------------------------------------
3 work-hours x $85 per hour = $255....         $10,000          $10,255
------------------------------------------------------------------------

Paperwork Reduction Act

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to penalty for 
failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act unless that collection of 
information displays a current valid OMB control number. The control 
number for the collection of information required by this NPRM is 2120-
0056. The paperwork cost associated with this NPRM has been detailed in 
the Costs of Compliance section of this document and includes time for 
reviewing instructions, as well as completing and reviewing the 
collection of information. Therefore, all reporting associated with 
this NPRM is mandatory. Send comments regarding this burden estimate or 
any other aspect of this collection of information, including 
suggestions for reducing this burden to: Information Collection 
Clearance Officer, Federal Aviation Administration, 10101 Hillwood 
Parkway, Fort Worth, TX 76177-1524.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes and associated appliances to the 
Director of the System Oversight Division.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Airbus SAS: Docket No. FAA-2019-0722; Product Identifier 2019-NM-
141-AD.

(a) Comments Due Date

    The FAA must receive comments by December 12, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A300 B2-1A, B2-1C, B2K-3C, 
B2-203, B4-2C, B4-103, and B4-203 airplanes, certificated in any 
category, all manufacturer serial numbers.

(d) Subject

    Air Transport Association (ATA) of America Code 29, Hydraulic 
power.

(e) Reason

    This AD was prompted by a report that bleed and air conditioning 
systems were contaminated by hydraulic fluid, and an investigation 
revealed that hydraulic fluid contaminations caused the failure of 
check valves installed on the hydraulic reservoir air pressurization 
system. The FAA is issuing this AD to address this condition, which, 
if not detected and corrected, could lead to leakage of the 
pressurization check valves, and, in case of pressurization line 
rupture, to loss of a hydraulic system, possibly resulting in 
reduced control of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) AD 
2019-0190, dated July 31, 2019 (``EASA AD 2019-0190'').

(h) Exceptions to EASA AD 2019-0190

    For purposes of determining compliance with the requirements of 
this AD:
    (1) Where EASA AD 2019-0190 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2019-0190 does not apply 
to this AD.
    (3) Paragraph (4) of EASA AD 2019-0190 specifies to report 
accomplishment of each test and any repair or replacement to Airbus 
within a certain compliance time. For this AD, report that action at 
the applicable time specified in paragraph (h)(3)(i) or (ii) of this 
AD.
    (i) If the action was done on or after the effective date of 
this AD: Submit the report within 30 days after the inspection.
    (ii) If the action was done before the effective date of this 
AD: Submit the report within 30 days after the effective date of 
this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA,

[[Page 57666]]

has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (j)(2) of this AD. Information 
may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's 
EASA Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): For any service information 
referenced in EASA AD 2019-0190 that contains RC procedures and 
tests: Except as required by paragraph (i)(2) of this AD, RC 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the procedures and tests identified as 
RC can be done and the airplane can be put back in an airworthy 
condition. Any substitutions or changes to procedures or tests 
identified as RC require approval of an AMOC.
    (4) Paperwork Reduction Act Burden Statement: A federal agency 
may not conduct or sponsor, and a person is not required to respond 
to, nor shall a person be subject to a penalty for failure to comply 
with a collection of information subject to the requirements of the 
Paperwork Reduction Act unless that collection of information 
displays a current valid OMB Control Number. The OMB Control Number 
for this information collection is 2120-0056. Public reporting for 
this collection of information is estimated to be approximately 1 
hour per response, including the time for reviewing instructions, 
completing and reviewing the collection of information. All 
responses to this collection of information are mandatory. Send 
comments regarding this burden estimate or any other aspect of this 
collection of information, including suggestions for reducing this 
burden to: Information Collection Clearance Officer, Federal 
Aviation Administration, 10101 Hillwood Parkway, Fort Worth, TX 
76177-1524.

(j) Related Information

    (1) For information about EASA AD 2019-0190, contact the EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
89990 6017; email ADs@easa.europa.eu; Internet www.easa.europa.eu. 
You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA, Transport 
Standards Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 
206-231-3195. This material may be found in the AD docket on the 
internet at http://www.regulations.gov by searching for and locating 
Docket No. FAA-2019-0722.
    (2) For more information about this AD, contact Dan Rodina, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3225.

    Issued in Des Moines, Washington, on October 18, 2019.
Michael Kaszycki,
Acting Manager, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-23394 Filed 10-25-19; 8:45 am]
 BILLING CODE 4910-13-P


