[Federal Register Volume 84, Number 171 (Wednesday, September 4, 2019)]
[Rules and Regulations]
[Pages 46432-46434]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-19013]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0608; Product Identifier 2019-NM-084-AD; Amendment 
39-19713; AD 2019-16-10]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting an airworthiness directive (AD) for 
certain The Boeing Company Model 787-8 airplanes. This AD requires a 
one-time inspection of the horizontal stabilizer pivot pin assemblies 
for misalignment and incorrect gapping, and applicable on-condition 
actions. This AD was prompted by a report of possible misalignment of 
the horizontal stabilizer pivot pin lock ring, outer pivot pin, and 
outboard spacer at final assembly. The FAA is issuing this AD to 
address the unsafe condition on these products.

DATES: This AD is effective September 19, 2019.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of September 
19, 2019.
    The FAA must receive comments on this AD by October 21, 2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this AD, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; internet https://www.myboeingfleet.com. You may 
view this referenced service information at the FAA, Transport 
Standards Branch, 2200 South 216th St., Des Moines, WA. For information 
on the availability of this material at the FAA, call 206-231-3195. It 
is also available on the internet at http://www.regulations.gov by 
searching for and locating Docket No. FAA-2019-0608.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0608; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this final rule, the regulatory evaluation, any comments 
received, and other information. The street address for Docket 
Operations is listed above. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Greg Rutar, Aerospace Engineer, 
Airframe Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des 
Moines, WA 98198; phone and fax: 206-231-3529; email: 
Greg.Rutar@faa.gov.

SUPPLEMENTARY INFORMATION: 

Discussion

    The FAA has received a report indicating possible misalignment of 
the horizontal stabilizer pivot pin lock ring, outer pivot pin, and 
outboard spacer at final assembly. One operator reported a left side 
pivot pin assembly that did not have a visible gap between the outboard 
nut and trap fitting. The pivot pin outboard spacer was not set 
correctly flush against the horizontal stabilizer pivot bearing and 
outboard washer due to a misaligned pivot pin lock ring. It was 
determined that only certain airplanes were possibly delivered with 
this condition. This condition, if not addressed, could result in 
decreased lateral load capacity, the loss of pivot pin retention parts, 
and consequent loss of the horizontal stabilizer and loss of control of 
the airplane.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Boeing Alert Requirements Bulletin B787-81205-
SB550009-00 RB, Issue 001, dated April 2, 2019. This service 
information describes procedures for a one-time detailed inspection of 
the horizontal stabilizer pivot pin assemblies for misalignment and 
incorrect gapping, and applicable on-condition actions. On-condition 
actions include replacing any incorrectly installed horizontal 
stabilizer pivot pin assembly. This service information is reasonably 
available because the interested parties have access to it through 
their normal

[[Page 46433]]

course of business or by the means identified in the ADDRESSES section.

FAA's Determination

    The FAA is issuing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

AD Requirements

    This AD requires accomplishment of the actions identified in Boeing 
Alert Requirements Bulletin B787-81205-SB550009-00 RB, Issue 001, dated 
April 2, 2019, described previously, except for any differences 
identified as exceptions in the regulatory text of this AD.
    For information on the procedures and compliance times, see this 
service information at http://www.regulations.gov by searching for and 
locating Docket No. FAA-2019-0608.

FAA's Justification and Determination of the Effective Date

    There are currently no domestic operators of this product. 
Therefore, the FAA finds that notice and opportunity for prior public 
comment are unnecessary and that good cause exists for making this 
amendment effective in less than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety and was not preceded by notice and an opportunity for public 
comment. However, the FAA invites you to send any written data, views, 
or arguments about this final rule. Send your comments to an address 
listed under the ADDRESSES section. Include the docket number FAA-2019-
0608 and Product Identifier 2019-NM-084-AD at the beginning of your 
comments. The FAA specifically invites comments on the overall 
regulatory, economic, environmental, and energy aspects of this final 
rule. The FAA will consider all comments received by the closing date 
and may amend this final rule because of those comments.
    The FAA will post all comments received, without change, to http://www.regulations.gov, including any personal information you provide. 
The FAA will also post a report summarizing each substantive verbal 
contact received about this final rule.

Costs of Compliance

    Currently, there are no affected U.S.-registered airplanes. If an 
affected airplane is imported and placed on the U.S. Register in the 
future, the FAA provides the following cost estimates to comply with 
this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                    Action                                 Labor cost               Parts cost        product
----------------------------------------------------------------------------------------------------------------
Inspection....................................  2 work-hours x $85 per hour =                 $0            $170
                                                 $170.
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary on-
condition actions that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need these on-condition actions:

                                     Estimated Costs of On-Condition Actions
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                 Action                           Labor cost                  Parts cost              product
----------------------------------------------------------------------------------------------------------------
Replacement.............................  12 work-hours x $85 per     Negligible................          $1,020
                                           hour = $1,020.
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some or all of the costs of this AD 
may be covered under warranty, thereby reducing the cost impact on 
affected individuals. The FAA does not control warranty coverage for 
affected individuals. As a result, the FAA has included all known costs 
in our cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation Programs'' 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.
    This AD is issued in accordance with authority delegated by the 
Executive Director, Aircraft Certification Service, as authorized by 
FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the Compliance and Airworthiness Division, but 
during this transition period, the Executive Director has delegated the 
authority to issue ADs applicable to transport category airplanes and 
associated appliances to the Director of the System Oversight Division.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

[[Page 46434]]

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2019-16-10 The Boeing Company: Amendment 39-19713; Docket No. FAA-
2019-0608; Product Identifier 2019-NM-084-AD.

(a) Effective Date

    This AD is effective September 19, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 787-8 airplanes, 
certificated in any category, as identified in Boeing Alert 
Requirements Bulletin B787-81205-SB550009-00 RB, Issue 001, dated 
April 2, 2019.

(d) Subject

    Air Transport Association (ATA) of America Code 55, Stabilizers.

(e) Unsafe Condition

    This AD was prompted by a report of possible misalignment of the 
horizontal stabilizer pivot pin lock ring, outer pivot pin, and 
outboard spacer at final assembly. The FAA is issuing this AD to 
address incorrect installation of the horizontal stabilizer pivot 
pin assemblies, which could result in decreased lateral load 
capacity, the loss of pivot pin retention parts, and consequent loss 
of the horizontal stabilizer and loss of control of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as specified by paragraph (h) of this AD: At the 
applicable times specified in the ``Compliance'' paragraph of Boeing 
Alert Requirements Bulletin B787-81205-SB550009-00 RB, Issue 001, 
dated April 2, 2019, do all applicable actions identified in, and in 
accordance with, the Accomplishment Instructions of Boeing Alert 
Requirements Bulletin B787-81205-SB550009-00 RB, Issue 001, dated 
April 2, 2019.
    Note 1 to paragraph (g): Guidance for accomplishing the actions 
required by this AD can be found in Boeing Alert Service Bulletin 
B787-81205-SB550009-00, dated April 2, 2019, which is referred to in 
Boeing Alert Requirements Bulletin B787-81205-SB550009-00 RB, Issue 
001, dated April 2, 2019.

(h) Exception to Service Information Specifications

    For purposes of determining compliance with the requirements of 
this AD: Where Boeing Alert Requirements Bulletin B787-81205-
SB550009-00 RB, Issue 001, dated April 2, 2019, uses the phrase 
``the Issue 001 date of Requirements Bulletin B787-81205-SB550009-00 
RB,'' this AD requires using ``the effective date of this AD.''

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO Branch, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or local Flight Standards District 
Office, as appropriate. If sending information directly to the 
manager of the certification office, send it to the attention of the 
person identified in paragraph (j) of this AD. Information may be 
emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by The Boeing Company Organization Designation 
Authorization (ODA) that has been authorized by the Manager, Seattle 
ACO Branch, FAA, to make those findings. To be approved, the repair 
method, modification deviation, or alteration deviation must meet 
the certification basis of the airplane, and the approval must 
specifically refer to this AD.

(j) Related Information

    For more information about this AD, contact Greg Rutar, 
Aerospace Engineer, Airframe Section, FAA, Seattle ACO Branch, 2200 
South 216th St., Des Moines, WA 98198; phone and fax: 206-231-3529; 
email: Greg.Rutar@faa.gov.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Boeing Alert Requirements Bulletin B787-81205-SB550009-00 
RB, Issue 001, dated April 2, 2019.
    (ii) [Reserved]
    (3) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; internet https://www.myboeingfleet.com.
    (4) You may view this service information at the FAA, Transport 
Standards Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 
206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Des Moines, Washington, on August 16, 2019.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-19013 Filed 9-3-19; 8:45 am]
 BILLING CODE 4910-13-P


