[Federal Register Volume 84, Number 190 (Tuesday, October 1, 2019)]
[Rules and Regulations]
[Pages 51960-51962]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-21238]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0498; Product Identifier 2019-NM-073-AD; Amendment 
39-19742; AD 2019-19-06]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Airbus SAS Model A330-202, -243, -243F, -302, -323, and -343 
airplanes. This AD was prompted by a report that cracks have been found 
within the ring gears of the slat geared rotary actuators (SGRAs) due 
to a change in the manufacturing process and inadequate post-production 
non-destructive testing for potential cracking. This AD requires an 
inspection to determine the part number and serial number of the SGRAs, 
and replacement of each affected SGRA with a serviceable part, as 
specified in a European Union Aviation Safety Agency (EASA) AD, which 
is incorporated by reference. The FAA is issuing this AD to address the 
unsafe condition on these products.

DATES: This AD is effective November 5, 2019.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of November 5, 
2019.

ADDRESSES: For the material incorporated by reference (IBR) in this AD, 
contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 89990 1000; email ADs@easa.europa.eu; internet 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at https://ad.easa.europa.eu. You may view this IBR material at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. 
For information on the availability of this material at the FAA, call 
206-231-3195. It is also available in the AD docket on the internet at 
http://www.regulations.gov by searching for and locating Docket No. 
FAA-2019-0498.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for

[[Page 51961]]

and locating Docket No. FAA-2019-0498; or in person at Docket 
Operations between 9 a.m. and 5 p.m., Monday through Friday, except 
Federal holidays. The AD docket contains this final rule, the 
regulatory evaluation, any comments received, and other information. 
The address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax: 206-231-3229.

SUPPLEMENTARY INFORMATION:

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2019-0093, dated April 26, 2019 
(``EASA AD 2019-0093'') (also referred to as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for certain Airbus SAS Model A330-202, -243, -243F, -302, -
323, and -343 airplanes.
    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to certain Airbus SAS 
Model A330-202, -243, -243F, -302, -323, and -343 airplanes. The NPRM 
published in the Federal Register on July 3, 2019 (84 FR 31772). The 
NPRM was prompted by a report that cracks have been found within the 
ring gears of the SGRAs due to a change in the manufacturing process 
and inadequate post-production non-destructive testing for potential 
cracking. The NPRM proposed to require an inspection to determine the 
part number and serial number of the SGRAs, and replacement of each 
affected SGRA with a serviceable part.
    The FAA is issuing this AD to address cracking of an SGRA, which, 
in combination with an independent failure on the second SGRA of the 
same slat surface, could lead to an uncontrolled movement of the 
affected slat surface in flight, or detachment of the slat surface, and 
could possibly result in damage to the stabilizers and reduced 
controllability of the airplane. See the MCAI for additional background 
information.

Comments

    The FAA gave the public the opportunity to participate in 
developing this final rule. The FAA received no comments on the NPRM or 
on the determination of the cost to the public.

Conclusion

    The FAA reviewed the relevant data and determined that air safety 
and the public interest require adopting this final rule as proposed, 
except for minor editorial changes. The FAA has determined that these 
minor changes:
     Are consistent with the intent that was proposed in the 
NPRM for addressing the unsafe condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM.

Related IBR Material Under 1 CFR Part 51

    EASA AD 2019-0093 describes procedures for an inspection to 
determine the part number and serial number of the SGRAs, and 
replacement of each affected part with a serviceable part.
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 2 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
               Labor cost                   Parts cost         Cost per product         Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Up to 2 work-hours x $85 per hour = Up                $0  Up to $170................  Up to $340.
 to $170.
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary on-
condition action that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need this on-condition action:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
          Labor cost             Parts cost         Cost per product
------------------------------------------------------------------------
Up to 15 work-hours x $85 per             (*)  Up to $1,275.*
 hour = Up to $1,275.
------------------------------------------------------------------------
* According to the manufacturer, some or all of the costs of this AD may
  be covered under warranty, thereby reducing the cost impact on
  affected individuals. The FAA does not control warranty coverage for
  affected individuals. As a result, the FAA has included all known
  costs in the cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This AD is issued in accordance with authority delegated by the 
Executive Director, Aircraft Certification Service, as authorized by 
FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the

[[Page 51962]]

Compliance and Airworthiness Division, but during this transition 
period, the Executive Director has delegated the authority to issue ADs 
applicable to transport category airplanes and associated appliances to 
the Director of the System Oversight Division.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2019-19-06 Airbus SAS: Amendment 39-19742; Docket No. FAA-2019-0498; 
Product Identifier 2019-NM-073-AD.

(a) Effective Date

    This AD is effective November 5, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A330-202, -243, -243F, -302, 
-323, and -343 airplanes, certificated in any category, as 
identified in European Union Aviation Safety Agency (EASA) AD 2019-
0093, dated April 26, 2019 (``EASA AD 2019-0093'').

(d) Subject

    Air Transport Association (ATA) of America Code 27, Flight 
control.

(e) Reason

    This AD was prompted by a report that cracks have been found 
within the ring gears of the slat geared rotary actuators (SGRAs) 
due to a change in the manufacturing process and inadequate post-
production non-destructive testing for potential cracking. The FAA 
is issuing this AD to address cracking of an SGRA, which, in 
combination with an independent failure on the second SGRA of the 
same slat surface, could lead to an uncontrolled movement of the 
affected slat surface in flight, or detachment of the slat surface, 
and could possibly result in damage to the stabilizers and reduced 
controllability of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2019-0093. All provisions specified in EASA 
AD 2019-0093 apply in this AD.

(h) Exceptions to EASA AD 2019-0093

    (1) For purposes of determining compliance with the requirements 
of this AD: Where EASA AD 2019-0093 refers to its effective date, 
this AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2019-0093 does not apply 
to this AD.

(i) No Reporting Requirement

    Although EASA AD 2019-0093 specifies to submit certain 
information to the manufacturer, this AD does not include that 
requirement.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (k) of this AD. Information may 
be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's 
EASA Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): For any service information 
referenced in EASA AD 2019-0093 that contains RC procedures and 
tests: Except as required by paragraph (j)(2) of this AD, RC 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the procedures and tests identified as 
RC can be done and the airplane can be put back in an airworthy 
condition. Any substitutions or changes to procedures or tests 
identified as RC require approval of an AMOC.

(k) Related Information

    For more information about this AD, contact Vladimir Ulyanov, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax: 206-231-3229.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2019-0093, 
dated April 26, 2019.
    (ii) [Reserved]
    (3) For information about EASA AD 2019-0093, contact the EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
89990 6017; email ADs@easa.europa.eu; Internet www.easa.europa.eu. 
You may find this EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this material at the FAA, Transport Standards 
Branch, 2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195. This 
material may be found in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-
2019-0498.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
fedreg.legal@nara.gov, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Des Moines, Washington, on September 19, 2019.
Suzanne Masterson,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-21238 Filed 9-30-19; 8:45 am]
BILLING CODE 4910-13-P


