[Federal Register Volume 84, Number 120 (Friday, June 21, 2019)]
[Proposed Rules]
[Pages 29108-29111]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-13051]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0436; Product Identifier 2019-NM-014-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc., Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Bombardier, Inc., Model CL-600-2B19 (Regional Jet Series 
100 & 440), CL-600-2C10 (Regional Jet Series 700, 701 & 702), CL-600-
2D15 (Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 900), 
and CL-600-2E25 (Regional Jet Series 1000) airplanes. This proposed AD 
was prompted by reports of power control unit (PCU) rod end fractures 
due to pitting corrosion. This proposed AD would require revising the 
existing maintenance or inspection program, as applicable, to 
incorporate new or more restrictive airworthiness limitations. This 
proposed AD would also require detailed inspections of the elevator PCU 
rod ends and applicable corrective actions. This proposed AD would also 
prohibit using certain aircraft maintenance manual tasks. The FAA is 
proposing this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by August 5, 
2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec 
H4S 1Y9, Canada; Widebody Customer Response Center North America toll-
free telephone 1-866-538-1247 or direct-dial telephone 1-514-855-2999; 
fax 514-855-7401; email ac.yul@aero.bombardier.com; internet http://www.bombardier.com. You may view this service information at the FAA, 
Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 206-
231-3195.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0436; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations is listed above. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Darren Gassetto, Aerospace Engineer, 
Mechanical Systems and Admin Services Section, FAA, New York ACO 
Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 
516-228-7323; fax 516-794-5531; email 9-avs-nyaco-cos@faa.gov.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2019-0436; 
Product Identifier 2019-NM-014-AD'' at the beginning of your comments. 
The FAA specifically invites comments on the overall regulatory, 
economic, environmental, and energy aspects of this NPRM. The FAA will 
consider all comments received by the closing date and may amend this 
NPRM because of those comments.
    The FAA will post all comments the agency receives, without change, 
to http://www.regulations.gov, including any personal information you 
provide. The FAA will also post a report summarizing each substantive 
verbal contact the agency receives about this NPRM.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian AD CF-2018-29, dated November 
2, 2018 (referred to after this as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for certain Bombardier, Inc., Model CL-600-2B19 (Regional Jet 
Series 100 & 440), CL-600-2C10 (Regional Jet Series 700, 701 & 702), 
CL-600-2D15 (Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 
900), and CL-600-2E25 (Regional Jet Series 1000) airplanes. The MCAI 
states:

    There have been several in-service reports of Power Control Unit 
(PCU) rod end fractures due to pitting corrosion. Investigation 
revealed that the PCU rod end spherical bearing could seize which, 
in turn, could induce a bending moment on the PCU output rod. This 
bending moment will eventually fracture the rod end. It was also 
noted that this failure mode typically occurs within the first 6000 
hours of aeroplane operation.
    This condition, if not corrected, could lead to a disconnect 
between the PCU and the control surface, potential loss of the 
control surface function or inadequate flutter suppression.
    This [Canadian] AD mandates incorporation of revised tasks into 
the maintenance manuals for detailed inspections of the PCU rod ends 
in order to allow timely detection of pitting corrosion [and would 
prohibit using certain aircraft maintenance manual tasks].

    You may examine the MCAI in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0436.

Related Service Information Under 1 CFR Part 51

    Bombardier, Inc., has issued the following service information.
    Bombardier Service Bulletin 670BA-27-074, dated June 22, 2017. This 
service information describes procedures for detailed inspections for 
pitting and corrosion of the left and right rod ends of the elevator 
PCUs and to make sure that the spherical ball and inner race of the rod 
ends move freely, and applicable corrective actions. Corrective actions 
include installing a new PCU.

[[Page 29109]]

    The following tasks describe operational checks of the elevator and 
rudder control systems, and a detailed inspection of the rudder PCU rod 
end spherical ball.
     Task 27-20-00-13, Operational Check of the Rudder Control 
System of Section 3--Systems and Powerplant Program, of the Bombardier 
Model CL-600-2B19 Series 100/200/440 Maintenance Planning Manual, Low 
Utilization Maintenance Program (MRLUMP-001), CSP A-054-009, Revision 
37, dated July 10, 2018 (``MRLUMP-001, Revision 37'').
     Task 27-23-01-01, Detailed Inspection of the Rudder PCU 
Rod End Spherical Ball, of MRLUMP-001, Revision 37.
     Task 27-31-00-05, Operational Check of the Elevator 
Control System, of MRLUMP-001, Revision 37.
    The following tasks describe operational tests of the elevator and 
rudder control systems, and a detailed inspection of the rudder PCU rod 
end spherical ball.
     Task 27-20-00-13, Operational Test of the Rudder Control 
System, of Section 3--Systems and Powerplant Program, of the Bombardier 
Model CL-600-2B19 Series 100/200/440 Maintenance Planning Manual, Low 
Utilization Maintenance Program (MRLUMP-002), CSP A-054-060, Revision 
37, dated July 10, 2018 (``MRLUMP-002, Revision 37'').
     Task 27-23-01-01, Detailed Inspection of the Rudder PCU 
Rod End Spherical Ball, of MRLUMP-002, Revision 37.
     Task 27-31-00-05, Operational Test of the Elevator Control 
System, of MRLUMP-002, Revision 37.
    The following tasks describe operational tests of the elevator and 
rudder PCUs, and a detailed inspection of the elevator PCU rod end 
spherical ball.
     Task 27-20-00-106, Operational Test of the Rudder PCUs 
(Duplicate CMR 27-20-00-106), of Section 3--Systems/Power Plant Tasks, 
of the Bombardier Model CL-600-2C10, CL-600-2D15, CL-600-2D24, Series 
700/705/900 Maintenance Planning Manual, Low Utilization Maintenance 
Program (LUMP), CSP BC-116, Revision 15, dated May 25, 2017 (``LUMP, 
Revision 15'').
     Task 273000-207, Operational Test of the Elevator Power-
Control Units (PCUs), of LUMP, Revision 15.
     Task 273000-215, Detailed Inspection of the Elevator PCU 
Rod End Spherical Ball, of LUMP, Revision 15.
    The following task describes an operational check of each elevator 
PCU.
     Task 273000-207, Operational Check of each Elevator PCU, 
of Subject 1-27, of Section 1, Systems and Powerplant Program, Volume 1 
of Part 1, Maintenance Review Board Report, Revision 18, dated July 25, 
2018, of the Bombardier Model CL-600-2C10, CL-600-2D15, CL-600-2D24, 
and CL-600-2E25 Series 700/705/900/1000 Maintenance Requirements 
Manual, CSP B-053.
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
and service information referenced above. The FAA is proposing this AD 
because the FAA evaluated all the relevant information and determined 
the unsafe condition described previously is likely to exist or develop 
on other products of the same type design.

Proposed Requirements of This NPRM

    This proposed AD would require revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations and to prohibit using certain 
aircraft maintenance manual tasks. Additionally, this proposed AD would 
require detailed inspections for pitting and corrosion of the left and 
right rod ends of the elevator PCUs and to make sure that the spherical 
ball and inner race of the rod ends move freely, and applicable 
corrective actions.

Costs of Compliance

    The FAA estimates that this proposed AD affects 1,008 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:

                                     Estimated Costs for Required Actions *
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
9 work-hours x $85 per hour = $765...........................              $0             $765         $771,120
----------------------------------------------------------------------------------------------------------------
* Table does not include estimated costs for revising the maintenance or inspection program.

    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although the FAA recognizes that this number may vary from operator to 
operator. In the past, the FAA has estimated that this action takes 1 
work-hour per airplane. Since operators incorporate maintenance or 
inspection program changes for their affected fleet(s), the FAA has 
determined that a per-operator estimate is more accurate than a per-
airplane estimate. Therefore, the FAA estimates the total cost per 
operator to be $7,650 (90 work-hours x $85 per work-hour).
    The FAA has received no definitive data that would enable the 
agency to provide cost estimates for the on-condition actions specified 
in this proposed AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by

[[Page 29110]]

FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the Compliance and Airworthiness Division, but 
during this transition period, the Executive Director has delegated the 
authority to issue ADs applicable to transport category airplanes and 
associated appliances to the Director of the System Oversight Division.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Will not affect intrastate aviation in Alaska; and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Bombardier, Inc.: Docket No. FAA-2019-0436; Product Identifier 2019-
NM-014-AD.

(a) Comments Due Date

    The FAA must receive comments by August 5, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc., airplanes, certificated in 
any category, as identified in paragraphs (c)(1) through (c)(4) of 
this AD.
    (1) Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes, 
serial numbers 7003 and subsequent.
    (2) Model CL-600-2C10 (Regional Jet Series 700, 701 & 702) 
airplanes, serial numbers 10002 through 10999 inclusive.
    (3) Model CL-600-2D15 (Regional Jet Series 705) and CL-600-2D24 
(Regional Jet Series 900) airplanes, serial numbers 15001 through 
15990 inclusive.
    (4) Model CL-600-2E25 (Regional Jet Series 1000) airplanes, 
serial numbers 19001 through 19990 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 27, Flight 
controls.

(e) Reason

    This AD was prompted by reports of power control unit (PCU) rod 
end fractures due to pitting corrosion. The FAA is issuing this AD 
to address this condition, which, if not detected and corrected, 
could lead to a disconnect between the PCU and the control surface, 
resulting in potential loss of the control surface function or 
inadequate flutter suppression.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Maintenance or Inspection Program Revision for Certain Airplanes 
Operating Under the Low Utilization Maintenance Program (LUMP)

    (1) For Model CL-600-2B19 airplanes operating under the LUMP: 
Within 90 days after the effective date of this AD, revise the 
existing maintenance or inspection program, as applicable, to 
incorporate the information specified in paragraphs (g)(1)(i) 
through (g)(1)(vi) of this AD. The initial compliance time for 
accomplishing the actions is within 90 days after the effective date 
of this AD; or within the applicable interval specified in Section 
3--Systems and Powerplant Program, of the Bombardier Model CL-600-
2B19 Series 100/200/440 Maintenance Planning Manual, Low Utilization 
Maintenance Program (MRLUMP-001), CSP A-054-009, Revision 37, dated 
July 10, 2018 (``MRLUMP-001, Revision 37''); or Section 3--Systems 
and Powerplant Program, of the Bombardier Model CL-600-2B19 Series 
100/200/440 Maintenance Planning Manual, Low Utilization Maintenance 
Program (MRLUMP-002), CSP A-054-060, Revision 37, dated July 10, 
2018 (``MRLUMP-002, Revision 37''), after the effective date of this 
AD; whichever occurs later.
    (i) Task 27-20-00-13, Operational Check of the Rudder Control 
System, of MRLUMP-001, Revision 37.
    (ii) Task 27-23-01-01, Detailed Inspection of the Rudder PCU Rod 
End Spherical Ball, of MRLUMP-001, Revision 37.
    (iii) Task 27-31-00-05, Operational Check of the Elevator 
Control System, of MRLUMP-001, Revision 37.
    (iv) Task 27-20-00-13, Operational Test of the Rudder Control 
System, of MRLUMP-002, Revision 37.
    (v) Task 27-23-01-01, Detailed Inspection of the Rudder PCU Rod 
End Spherical Ball, of MRLUMP-002, Revision 37.
    (vi) Task 27-31-00-05, Operational Test of the Elevator Control 
System, of MRLUMP-002, Revision 37.
    (2) For Model CL-600-2C10 airplanes having serial numbers 10004, 
10040, 10043, 10052, 10100, 10164, 10183, 10187, 10204, 10206, 
10217, 10247, 10289, 10332, and 10343 operating under the LUMP; and 
Model CL-600-2D15 and CL-600-2D24 airplanes having serial numbers 
15158, 15278, and 15370 operating under the LUMP: Within 30 days 
from the effective date of this AD, revise the existing maintenance 
or inspection program, as applicable, to incorporate the information 
specified in paragraphs (g)(2)(i) through (g)(2)(iii) of this AD. 
The initial compliance time for accomplishing the actions is within 
30 days after the effective date of this AD; or within the 
applicable interval specified in Section 3--Systems/Power Plant 
Tasks, of the Bombardier Model CL-600-2C10, CL-600-2D15, CL-600-
2D24, Series 700/705/900 Maintenance Planning Manual, Low 
Utilization Maintenance Program (LUMP), CSP BC-116, Revision 15, 
dated May 25, 2017 (``LUMP, Revision 15''), after the effective date 
of this AD; whichever occurs later.
    (i) Task 27-20-00-106, Operational Test of the Rudder PCUs 
(Duplicate CMR 27-20-00-106), of LUMP, Revision 15.
    (ii) Task 273000-207, Operational Test of the Elevator Power-
Control Units (PCUs), of LUMP, Revision 15.
    (iii) Task 273000-215, Detailed Inspection of the Elevator PCU 
Rod End Spherical Ball, of LUMP, Revision 15.

(h) Maintenance or Inspection Program Revision for Certain Airplanes 
That Are Not Operating Under the LUMP

    For Model CL-600-2C10, CL-600-2D15, CL-600-2D24, and CL-600-2E25 
airplanes that are not operating under the LUMP: Within 30 days from 
the effective date of this AD, revise the existing maintenance or 
inspection program, as applicable, to incorporate the information 
specified in task 273000-207, Operational Check of each Elevator 
PCU, of Subject 1-27, of Section 1, Systems and Powerplant Program, 
Volume 1 of Part 1, Maintenance Review Board Report, Revision 18, 
dated July 25, 2018, of the Bombardier Model CL-600-2C10, CL-600-
2D15, CL-600-2D24, and CL-600-2E25 Series 700/705/900/1000 
Maintenance Requirements Manual, CSP B-053, (``CSP B-053, Revision 
18''). The initial compliance time for accomplishing the actions is 
within 30 days after the effective date of this AD; or within the 
applicable interval specified in CSP B-053, Revision 18, after the 
effective date of this AD; whichever occurs later.

(i) No Alternative Actions or Intervals

    After the existing maintenance or inspection program has been 
revised as required by paragraph (g) or (h) of this AD, no 
alternative actions (e.g., inspections) or intervals may be used 
unless the actions and intervals are approved as an alternative 
method of compliance (AMOC) in accordance with the procedures 
specified in paragraph (n)(1) of this AD.

[[Page 29111]]

(j) First Inspection of the Elevator PCU Rod End for Certain Airplanes

    For Model CL-600-2C10, CL-600-2D15, CL-600-2D24, and CL-600-2E25 
airplanes that are not operating under the LUMP, and that have 
accumulated less than 6,000 total flight hours as of the effective 
date of this AD: Within the compliance time indicated in figure 1 to 
paragraph (j) of this AD, perform a detailed inspection for pitting 
and corrosion of the left and right rod ends of the elevator PCUs 
and to make sure that the spherical ball and inner race of the rod 
ends move freely, and do all applicable corrective actions, in 
accordance with paragraph 2.B. of the Accomplishment Instructions of 
Bombardier Service Bulletin 670BA-27-074, dated June 22, 2017. Do 
all applicable corrective actions before further flight.
[GRAPHIC] [TIFF OMITTED] TP21JN19.000

(k) Second Inspection of the Elevator PCU Rod End for Certain Airplanes

    (1) For Model CL-600-2C10, CL-600-2D15, CL-600-2D24, and CL-600-
2E25 airplanes that are not operating under the LUMP, and that have 
accumulated 2,600 total flight hours or less at the time of the 
inspection required by paragraph (j) of this AD: Before the 
accumulation of 3,400 total flight hours, perform an additional 
detailed inspection for pitting and corrosion of the left and right 
rod ends of the elevator PCUs and to make sure that the spherical 
ball and inner race of the rod ends move freely, and do all 
applicable corrective actions, in accordance with paragraph 2.B. of 
the Accomplishment Instructions of Bombardier Service Bulletin 
670BA-27-074, dated June 22, 2017. Do all applicable corrective 
actions before further flight.
    (2) For airplanes that have accumulated more than 2,600 total 
flight hours at the time of the inspection required by paragraph (j) 
of this AD: A second inspection is not applicable.

(l) No Inspection for Certain Airplanes

    The requirements of paragraphs (j) and (k) are not applicable to 
airplanes that have accumulated 6,000 total flight hours or more as 
of the effective date of this AD.

(m) Service Information Prohibition for Certain Airplanes

    For all Model CL-600-2B19 airplanes: After 30 days from the 
effective date of this AD, this AD prohibits the use of the aircraft 
maintenance manual (AMM) tasks specified in paragraphs (m)(1) 
through (m)(3) of this AD.
    (1) Task 10-12-00-550-804, Short-Term Storage Return-to-Service 
Maintenance Checks, of the Bombardier CL-600-2B19 Series 100/200/440 
AMM, CSP A-001, Revision 55, dated April 10, 2017, or earlier 
revisions of this task.
    (2) Task 27-23-01-220-801, Detailed Inspection of the Rudder PCU 
Rod End Spherical Ball, of the Bombardier CL-600-2B19 Series 100/
200/440 AMM, CSP A-001, Revision 54, dated October 10, 2016, or 
earlier revisions of this task.
    (3) Task 27-33-01-220-801, Detailed Inspection of the Elevator 
PCU Rod End Spherical Ball, of the Bombardier CL-600-2B19 Series 
100/200/440 AMM, CSP A-001, Revision 54, dated October 10, 2016, or 
earlier revisions of this task.

(n) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York ACO Branch, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or local Flight Standards District Office, as appropriate. 
If sending information directly to the manager of the certification 
office, send it to ATTN: Program Manager, Continuing Operational 
Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before 
using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO 
Branch, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If 
approved by the DAO, the approval must include the DAO-authorized 
signature.

(o) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian AD CF-2018-29, dated November 2, 2018, for related 
information. This MCAI may be found in the AD docket on the internet 
at http://www.regulations.gov by searching for and locating Docket 
No. FAA-2019-0436.
    (2) For more information about this AD, contact Darren Gassetto, 
Aerospace Engineer, Mechanical Systems and Admin Services Section, 
FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, 
NY 11590; telephone 516-228-7323; fax 516-794-5531; email 9-avs-nyaco-cos@faa.gov.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; Widebody Customer Response Center 
North America toll-free telephone 1-866-538-1247 or direct-dial 
telephone 1-514-855-2999; fax 514-855-7401; email 
ac.yul@aero.bombardier.com; internet http://www.bombardier.com. You 
may view this service information at the FAA, Transport Standards 
Branch, 2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195.

    Issued in Des Moines, Washington, on June 12, 2019.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-13051 Filed 6-20-19; 8:45 am]
 BILLING CODE 4910-13-P


