[Federal Register Volume 84, Number 108 (Wednesday, June 5, 2019)]
[Proposed Rules]
[Pages 26027-26030]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-11621]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0403; Product Identifier 2019-NM-012-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Airbus SAS Model A320-214 and -271N airplanes and Model A321-
211 and -231 airplanes. This proposed AD was prompted by a test of a 
new wall partition for a certain cabin attendant seat model that 
revealed the backrest was permanently deformed and did not allow the 
seat pan to return to a full-up position; investigation results 
identified that a heat treatment had not been applied on certain 
backframes. This proposed AD would require modifying the affected cabin 
attendant seats, as specified in an European Aviation Safety Agency 
(EASA) AD, which will be incorporated by reference. We are proposing 
this AD to address the unsafe condition on these products.

DATES: We must receive comments on this proposed AD by July 22, 2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For the material identified in this NPRM that will be incorporated 
by reference, contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, 
Germany; telephone +49 221 89990 1000; email ADs@easa.europa.eu; 
internet www.easa.europa.eu. You may find this IBR material on the EASA 
website at https://ad.easa.europa.eu. You may view this IBR material at 
the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, 
WA. For

[[Page 26028]]

information on the availability of this material at the FAA, call 206-
231-3195. It is also available in the AD docket on the internet at 
http://www.regulations.gov.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0403; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations (telephone 800-
647-5527) is listed above. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Sanjay Ralhan, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3223.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2019-0403; 
Product Identifier 2019-NM-012-AD'' at the beginning of your comments. 
We specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this NPRM. We will consider all 
comments received by the closing date and may amend this NPRM based on 
those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this NPRM.

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2019-0005, dated January 14, 2019 
(``EASA AD 2019-0005'') (also referred to as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for certain Airbus SAS Model A320-214 and -271N airplanes and 
Model A321-211 and -231 airplanes. The MCAI states:

    During a test of a new wall partition for cabin attendant seat 
model 2428, the backrest was found permanently deformed and did not 
allow the seat pan to return to a full-up position. Investigation 
results identified that a heat treatment had not been applied on 
certain backframes, which could lead to permanent deformation of the 
seat backrest.
    This condition, if not corrected, could reduce the escape path 
through the adjacent exit door in case of evacuation, possibly 
resulting in injury to aeroplane occupants.
    To address this potential unsafe condition, Airbus issued the 
applicable SB [service bulletin], which refers to Goodrich SB, 
providing instructions to modify affected parts by replacing the 
backframe, and to add a placard after modification.
    For the reasons described above, this [EASA] AD requires 
modification of the affected parts.

Related IBR Material Under 1 CFR Part 51

    EASA AD 2019-0005 describes procedures for modifying affected cabin 
attendant seats (which includes an inspection to determine the part 
number and serial number of the cabin attendant seat) by replacing the 
backrest and adding a placard. This material is reasonably available 
because the interested parties have access to it through their normal 
course of business or by the means identified in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI referenced 
above. We are proposing this AD because we evaluated all pertinent 
information and determined an unsafe condition exists and is likely to 
exist or develop on other products of the same type design.

Proposed Requirements of This NPRM

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2019-0005, as incorporated by reference, described 
previously, except for any differences identified as exceptions in the 
regulatory text of this AD. This proposed AD also would require sending 
the inspection results to Airbus SAS.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA worked with Airbus and EASA to develop a process to 
use certain EASA ADs as the primary source of information for 
compliance with requirements for corresponding FAA ADs. As a result, 
EASA AD 2019-0005 will be incorporated by reference in the FAA final 
rule. This proposed AD would, therefore, require compliance with the 
provisions specified in EASA AD 2019-0005, except for any differences 
identified as exceptions in the regulatory text of this proposed AD. 
Service information specified in EASA AD 2019-0005 that is required for 
compliance with EASA AD 2019-0005 will be available on the internet at 
http://www.regulations.gov by searching for and locating Docket No. 
FAA-2019-0403 after the FAA final rule is published.

Costs of Compliance

    We estimate that this proposed AD affects 19 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                     Estimated Costs for Required Actions *
----------------------------------------------------------------------------------------------------------------
              Labor cost                      Parts cost            Cost per product      Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Up to 462 work-hours x $85 per hour =  N/A....................  Up to $39,270..........  Up to $746,130.
 $39,270.
----------------------------------------------------------------------------------------------------------------
* Table does not include estimated costs for reporting.

    We estimate that it would take about 1 work-hour per product to 
comply with the proposed reporting requirement in this proposed AD. The 
average labor rate is $85 per hour. Based on these figures, we estimate 
the cost of reporting the modification results on U.S. operators to be 
$85 per product.
    We have received no definitive data that would enable us to provide 
cost estimates for the actions specified in this proposed AD.
    According to the manufacturer, some or all of the costs of this 
proposed AD may be covered under warranty, thereby reducing the cost 
impact on affected individuals. We do not control warranty coverage for 
affected individuals. As a

[[Page 26029]]

result, we have included all known costs in our cost estimate.

Paperwork Reduction Act

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to penalty for 
failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act unless that collection of 
information displays a current valid OMB control number. The control 
number for the collection of information required by this NPRM is 2120-
0056. The paperwork cost associated with this NPRM has been detailed in 
the Costs of Compliance section of this document and includes time for 
reviewing instructions, as well as completing and reviewing the 
collection of information. Therefore, all reporting associated with 
this NPRM is mandatory. Comments concerning the accuracy of this burden 
and suggestions for reducing the burden should be directed to the FAA 
at 800 Independence Ave. SW, Washington, DC 20591, ATTN: Information 
Collection Clearance Officer, AES-200.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes and associated appliances to the 
Director of the System Oversight Division.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Airbus SAS: Docket No. FAA-2019-0403; Product Identifier 2019-NM-
012-AD.

(a) Comments Due Date

    We must receive comments by July 22, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A320-214 and -271N airplanes 
and Model A321-211 and -231 airplanes, certificated in any category, 
as identified in European Aviation Safety Agency (EASA) AD 2019-
0005, dated January 14, 2019 (``EASA AD 2019-0005'').

(d) Subject

    Air Transport Association (ATA) of America Code 25, Equipment/
furnishings.

(e) Reason

    This AD was prompted by a test of a new wall partition for a 
certain cabin attendant seat model that revealed the backrest was 
permanently deformed and did not allow the seat pan to return to a 
full-up position; investigation results identified that a heat 
treatment had not been applied on certain backframes. We are issuing 
this AD to address this condition, which, if not corrected, could 
reduce the escape path through the adjacent exit door in case of 
evacuation, possibly resulting in injury to passengers or 
flightcrew.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2019-0005.

(h) Exceptions to EASA AD 2019-0005

    (1) For purposes of determining compliance with the requirements 
of this AD: Where EASA AD 2019-0005 refers to its effective date, 
this AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2019-0005 does not apply 
to this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (j)(2) of this AD. Information 
may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's 
EASA Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): For any service information 
referenced in EASA AD 2019-0005 that contains RC procedures and 
tests: Except as required by paragraph (i)(2) of this AD, RC 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated

[[Page 26030]]

from using accepted methods in accordance with the operator's 
maintenance or inspection program without obtaining approval of an 
AMOC, provided the procedures and tests identified as RC can be done 
and the airplane can be put back in an airworthy condition. Any 
substitutions or changes to procedures or tests identified as RC 
require approval of an AMOC.
    (4) Paperwork Reduction Act Burden Statement: A federal agency 
may not conduct or sponsor, and a person is not required to respond 
to, nor shall a person be subject to a penalty for failure to comply 
with a collection of information subject to the requirements of the 
Paperwork Reduction Act unless that collection of information 
displays a current valid OMB Control Number. The OMB Control Number 
for this information collection is 2120-0056. Public reporting for 
this collection of information is estimated to be approximately 1 
hour per response, including the time for reviewing instructions, 
completing and reviewing the collection of information. All 
responses to this collection of information are mandatory. Comments 
concerning the accuracy of this burden and suggestions for reducing 
the burden should be directed to the FAA at: 800 Independence Ave. 
SW, Washington, DC 20591, Attn: Information Collection Clearance 
Officer, AES-200.

(j) Related Information

    (1) For information about EASA AD 2019-0005, contact the EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
89990 6017; email ADs@easa.europa.eu; Internet www.easa.europa.eu. 
You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this EASA AD at the FAA, Transport 
Standards Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 
206-231-3195. EASA AD 2019-0005 may be found in the AD docket on the 
internet at http://www.regulations.gov by searching for and locating 
Docket No. FAA-2019-0403.
    (2) For more information about this AD, contact Sanjay Ralhan, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3223.

    Issued in Des Moines, Washington, on May 28, 2019.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-11621 Filed 6-4-19; 8:45 am]
 BILLING CODE 4910-13-P


