[Federal Register Volume 84, Number 88 (Tuesday, May 7, 2019)]
[Proposed Rules]
[Pages 19881-19885]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-09264]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0257; Product Identifier 2018-NM-175-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to supersede Airworthiness Directive (AD) 2018-20-
06, which applies to certain Airbus SAS Model A300 F4-600R series 
airplanes. AD 2018-20-06 requires repetitive high frequency eddy 
current (HFEC) inspections of the aft lower deck cargo door (LDCD) 
frame forks; a one-time check of the LDCD clearances; and a one-time 
detailed visual inspection of hooks, eccentric bushes, and x-stops; and 
corrective actions if necessary. Since we issued AD 2018-20-06, we 
determined certain compliance times need to be revised, depending on 
frame fork configuration. This proposed AD would continue to require 
the actions of AD 2018-20-06 and would require new compliance times, 
depending on frame fork configuration. We are proposing this AD to 
address the unsafe condition on these products.

DATES: We must receive comments on this proposed AD by June 21, 2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Airbus 
SAS, Airworthiness Office--EAW, Rond-Point Emile Dewoitine No: 2, 31700 
Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 
51; email account.airworth-eas@airbus.com; internet http://www.airbus.com. You may view this referenced service information at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. 
For information on the availability of this material at the FAA, call 
206-231-3195.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0257; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations (phone 800-647-
5527) is in the ADDRESSES section. Comments will be available in the AD 
docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3225.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2019-0257; 
Product Identifier 2018-NM-175-AD'' at the beginning of your comments. 
We specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this proposed AD. We will consider 
all comments received by the closing date and may amend this proposed 
AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    We issued AD 2018-20-06, Amendment 39-19440 (83 FR 49265, October 
1, 2018) (``AD 2018-20-06''), for certain Airbus SAS Model A300 F4-

[[Page 19882]]

600R series airplanes. AD 2018-20-06 requires repetitive HFEC 
inspections of the aft LDCD frame forks; a one-time check of the LDCD 
clearances; and a one-time detailed visual inspection of hooks, 
eccentric bushes, and x-stops; and corrective actions if necessary. AD 
2018-20-06 resulted from a report of two adjacent frame forks that were 
found cracked on the aft LDCD of two airplanes during scheduled 
maintenance, and the introduction of frame fork reinforcement or repair 
procedures that, when done, allow an extension of repetitive inspection 
intervals. We issued AD 2018-20-06 to address cracked or ruptured aft 
LDCD frames, which could allow loads to be transferred to the remaining 
structural elements. This condition could lead to the rupture of one or 
more vertical aft LDCD frames, which could result in reduced structural 
integrity of the aft LDCD.

Actions Since AD 2018-20-06 Was Issued

    Since we issued AD 2018-20-06, we have determined that certain 
compliance times need to be reduced, depending on the frame fork 
configuration. In addition, certain compliance times are extended.
    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Union, has issued EASA AD 
2018-0266, dated December 11, 2018 (referred to after this as the 
Mandatory Continuing Airworthiness Information, or ``the MCAI''), to 
correct an unsafe condition for certain Airbus SAS Model A300 F4-600R 
series airplanes. The MCAI states:

    During scheduled maintenance at frames (FR) 61 and FR61A on the 
aft lower deck cargo door (LDCD) of two [Airbus SAS] A300-600F4 
aeroplanes, two adjacent frame forks were found cracked. Subsequent 
analysis determined that, in case of cracked or ruptured aft cargo 
door frame(s), loads will be transferred to the remaining structural 
elements. However, these secondary load paths will be able to 
sustain the loads for a limited number of flight cycles (FC) only.
    This condition, if not detected and corrected, could lead to the 
rupture of one or more vertical aft cargo door frame(s), resulting 
in reduced structural integrity of the aft cargo door.
    To address this unsafe condition, Airbus issued Alert Operators 
Transmission (AOT) A52W011-15 to provide inspection instructions, 
and, consequently, EASA issued AD 2015-0152 to require repetitive 
inspections of the aft LDCD frame forks and, depending on findings, 
the accomplishment of applicable corrective action(s). Subsequently, 
Airbus published the modification SB [service bulletin] to provide 
frame fork reinforcement instructions, and the inspection SB to 
provide instructions to inspect the cargo door for cracks, as well 
as for frame fork replacement, including provisions for extended 
inspection intervals. EASA revised the AD accordingly.
    Since EASA AD 2015-0152R1 [which corresponds to FAA AD 2018-20-
06] was issued, further investigations results allowed Airbus to 
define new thresholds and inspection intervals according to the 
frame fork configuration. Consequently, the inspection SB was 
revised to include these new thresholds and intervals.
    For the reasons described above, this [EASA] AD retains the 
requirements of EASA AD 2015-0152R1, which is superseded, and 
introduces new thresholds and intervals, depending on frame fork 
configuration.

    You may examine the MCAI in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0257.

Related Service Information Under 1 CFR Part 51

    This proposed AD would require Airbus Alert Operators Transmission 
A52W011-15, Revision 00, including Appendices 1, 2, 3, and 4, dated 
July 23, 2015, which the Director of the Federal Register approved for 
incorporation by reference as of January 26, 2017 (81 FR 93801, 
December 22, 2016).
    This proposed AD would also require Airbus Service Bulletin A300-
52-6085, Revision 01, dated May 2, 2018; and Airbus Service Bulletin 
A300-52-6086, Revision 01, dated May 29, 2018; which the Director of 
the Federal Register approved for incorporation by reference as of 
November 5, 2018 (83 FR 49265, October 1, 2018).
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all the relevant information and determined the unsafe 
condition described previously is likely to exist or develop on other 
products of the same type design.

Proposed Requirements of This NPRM

    This proposed AD would retain the actions of AD 2018-20-06. This 
proposed AD would require accomplishing the actions specified in the 
service information described previously.

Costs of Compliance

    We estimate that this proposed AD affects 58 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on  U.S.
                Action                         Labor cost           Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Retained actions from AD 2018-20-06...  17 work-hours x $85 per               $0          $1,445         $83,810
                                         hour = $1,445.
----------------------------------------------------------------------------------------------------------------

    The new requirements of this proposed AD add no additional economic 
burden.
    We estimate the following costs to do any necessary on-condition 
actions that would be required based on the results of any required 
actions. We have no way of determining the number of aircraft that 
might need these on-condition actions:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
           Labor cost                 Parts cost       Cost per product
------------------------------------------------------------------------
Up to 65 work-hours x $85 per     Up to $10,000.....  Up to $15,525.
 hour = $5,525.
------------------------------------------------------------------------


[[Page 19883]]

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes and associated appliances to the 
Director of the System Oversight Division.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866,
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    3. Will not affect intrastate aviation in Alaska, and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Airworthiness Directive (AD) 
2018-20-06, Amendment 39-19440 (83 FR 49265, October 1, 2018), and 
adding the following new AD:

Airbus SAS: Docket No. FAA-2019-0257; Product Identifier 2018-NM-
175-AD.

(a) Comments Due Date

    We must receive comments by June 21, 2019.

(b) Affected ADs

    This AD replaces 2018-20-06, Amendment 39-19440 (83 FR 49265, 
October 1, 2018) (``AD 2018-20-06'').

(c) Applicability

    This AD applies to Airbus SAS Model A300 F4-605R and F4-622R 
airplanes, certificated in any category, on which Airbus 
modification 12046 has been embodied in production. Modification 
12046 has been embodied in production on manufacturer serial numbers 
(MSNs) 0805 and above, except MSNs 0836, 0837, and 0838.

(d) Subject

    Air Transport Association (ATA) of America Code 52, Doors.

(e) Reason

    This AD was prompted by a report of two adjacent frame forks 
that were found cracked on the aft lower deck cargo door (LDCD) of 
two airplanes during scheduled maintenance, and a determination that 
certain compliance times need to be revised. We are issuing this AD 
to address cracked or ruptured aft LDCD frames, which could allow 
loads to be transferred to the remaining structural elements. This 
condition could lead to the rupture of one or more vertical aft LDCD 
frames, which could result in reduced structural integrity of the 
aft LDCD.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) New Affected Part Definition

    For the purposes of this AD, an affected part is a frame fork 
having a part number identified in figure 1 to paragraph (g) of this 
AD.
[GRAPHIC] [TIFF OMITTED] TP07MY19.000

(h) Retained Inspection Requirements and On-Condition Actions, With 
Revised Compliance Language

    This paragraph restates the requirements of paragraph (g) of AD 
2018-20-06, with revised compliance language. At the applicable time 
specified in paragraph (i) of this AD, or before exceeding the 
threshold defined in figure 2 to paragraph (h) of this AD, whichever 
occurs later: Do the actions specified in paragraphs (h)(1), (h)(2), 
and (h)(3) of this AD. Repeat the high frequency eddy current (HFEC) 
inspection specified in paragraph (h)(3) of this AD at all LDCD 
frame fork stations having affected parts thereafter at intervals 
not to exceed the applicable times specified in figure 2 to 
paragraph (h) of this AD.
    (1) A one-time check of the aft LDCD clearances ``U'' and ``V'' 
between the latching hooks and the eccentric bush at frame (FR) 60 
through FR64A, in accordance with the instructions of Airbus Alert 
Operators

[[Page 19884]]

Transmission A52W011-15, Revision 00, dated July 23, 2015; or the 
Accomplishment Instructions of Airbus Service Bulletin A300-52-6086, 
Revision 01, dated May 29, 2018. If any value outside tolerance is 
found, adjust the latching hook before further flight, in accordance 
with the instructions of Airbus Alert Operators Transmission 
A52W011-15, Revision 00, dated July 23, 2015; or the Accomplishment 
Instructions of Airbus Service Bulletin A300-52-6086, Revision 01, 
dated May 29, 2018.
    (2) A one-time detailed inspection to detect signs of wear of 
the hooks, eccentric bushes, and x-stops, in accordance with the 
instructions of Airbus Alert Operators Transmission A52W011-15, 
Revision 00, dated July 23, 2015. If any wear is found, do all 
applicable corrective actions before further flight, in accordance 
with the instructions of Airbus Alert Operators Transmission 
A52W011-15, Revision 00, dated July 23, 2015.
    (3) An HFEC inspection to detect cracking at all frame fork 
stations of the aft LDCD, in accordance with the instructions of 
Airbus Alert Operators Transmission A52W011-15, Revision 00, dated 
July 23, 2015; or the Accomplishment Instructions of Airbus Service 
Bulletin A300-52-6086, Revision 01, dated May 29, 2018. If any crack 
is found, before further flight, replace the cracked frame fork, in 
accordance with the instructions of Airbus Alert Operators 
Transmission A52W011-15, Revision 00, dated July 23, 2015; repair 
the cracked frame fork, in accordance with the Accomplishment 
Instructions of Airbus Service Bulletin A300-52-6086, Revision 01, 
dated May 29, 2018; or modify (reinforce) the cracked frame fork, 
including doing all applicable related investigative and corrective 
actions, in accordance with the Accomplishment Instructions of 
Airbus Service Bulletin A300-52-6085, Revision 01, dated May 2, 
2018, except as required by paragraph (j) of this AD.
[GRAPHIC] [TIFF OMITTED] TP07MY19.001


[[Page 19885]]



(i) Retained Compliance Times, With No Changes

    At the later of the times specified in paragraphs (i)(1) and 
(i)(2) of this AD, do the actions required by paragraph (h) of this 
AD.
    (1) Before the accumulation of 4,500 total flight cycles.
    (2) At the applicable time specified by paragraph (i)(2)(i) or 
(i)(2)(ii) of this AD.
    (i) For airplanes that have accumulated 8,000 or more total 
flight cycles as of January 26, 2017 (the effective date of AD 2016-
25-03, Amendment 39-18729 (81 FR 93801, December 22, 2016) (``AD 
2016-25-03'')): Within 100 flight cycles after January 26, 2017.
    (ii) For airplanes that have accumulated fewer than 8,000 total 
flight cycles as of January 26, 2017 (the effective date of AD 2016-
25-03): Within 400 flight cycles after January 26, 2017.

(j) Service Information Exception

    Where Airbus Service Bulletin A300-52-6085, Revision 01, dated 
May 2, 2018, specifies to contact Airbus for appropriate action: 
Before further flight, accomplish corrective actions in accordance 
with the procedures specified in paragraph (n)(2) of this AD.

(k) No Terminating Action

    Accomplishment of corrective actions on an airplane as required 
by paragraph (h)(1) or (h)(2) of this AD, or repair, modification, 
or replacement of a frame fork as required by paragraph (h)(3) of 
this AD, on the aft LDCD of an airplane does not constitute 
terminating action for the repetitive HFEC inspections required by 
paragraph (h)(3) of this AD for that airplane.

(l) No Reporting

    Although the Accomplishment Instructions of Airbus Alert 
Operators Transmission A52W011-15, Revision 00, dated July 23, 2015; 
and Airbus Service Bulletin A300-52-6086, Revision 01, dated May 29, 
2018; specify to submit certain information to the manufacturer, 
this AD does not include that requirement.

(m) Credit for Previous Actions

    (1) This paragraph provides credit for actions required by 
paragraphs (h)(1) and (h)(3) of this AD, if those actions were 
performed before the effective date of this AD using Airbus Service 
Bulletin A300-52-6086, Revision 00, dated December 25, 2016.
    (2) This paragraph provides credit for actions required by 
paragraph (h)(3) of this AD, if those actions were performed before 
the effective date of this AD using Airbus Service Bulletin A300-52-
6085, Revision 00, dated December 22, 2016.

(n) Other FAA AD Provisions

    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (o)(2) of this AD. Information 
may be emailed to 9-ANM-116-AMOC-REQUESTS@faa.gov.
    (i) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (ii) AMOCs approved previously for AD 2018-20-06 are approved as 
AMOCs for the corresponding provisions of this AD.
    (2) Contacting the Manufacturer: As of the effective date of 
this AD, for any requirement in this AD to obtain corrective actions 
from a manufacturer, the action must be accomplished using a method 
approved by the Manager, International Section, Transport Standards 
Branch, FAA; or the European Aviation Safety Agency (EASA); or 
Airbus SAS's EASA Design Organization Approval (DOA). If approved by 
the DOA, the approval must include the DOA-authorized signature.

(o) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) EASA AD 2018-0266, dated December 11, 2018, for related 
information. This MCAI may be found in the AD docket on the internet 
at http://www.regulations.gov by searching for and locating Docket 
No. FAA-2019-0257.
    (2) For more information about this AD, contact Dan Rodina, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3225.
    (3) For service information identified in this AD, contact 
Airbus SAS, Airworthiness Office--EAW, Rond-Point Emile Dewoitine 
No: 2, 31700 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax 
+33 5 61 93 44 51; email account.airworth-eas@airbus.com; internet 
http://www.airbus.com. You may view this service information at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, 
WA. For information on the availability of this material at the FAA, 
call 206-231-3195.

    Issued in Des Moines, Washington, on April 25, 2019.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-09264 Filed 5-6-19; 8:45 am]
BILLING CODE 4910-13-P


