
[Federal Register Volume 84, Number 43 (Tuesday, March 5, 2019)]
[Proposed Rules]
[Pages 7835-7837]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-03830]



[[Page 7835]]

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0116; Product Identifier 2018-NM-152-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Airbus SAS Model A318, A319, A320, and A321 series airplanes. 
This proposed AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. This proposed AD 
would require revising the existing maintenance or inspection program, 
as applicable, to incorporate new or more restrictive fuel 
airworthiness limitations. We are proposing this AD to address the 
unsafe condition on these products.

DATES: We must receive comments on this proposed AD by April 19, 2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Airbus 
SAS, Airworthiness Office--EIAS, Rond-Point Emile Dewoitine No: 2, 
31700 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 
93 44 51; email account.airworth-eas@airbus.com; internet http://www.airbus.com. You may view this service information at the FAA, 
Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 206-
231-3195.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0116; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations (phone: 800-647-
5527) is in the ADDRESSES section. Comments will be available in the AD 
docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Sanjay Ralhan, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3223.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2019-0116; 
Product Identifier 2018-NM-152-AD'' at the beginning of your comments. 
We specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this NPRM. We will consider all 
comments received by the closing date and may amend this NPRM because 
of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this NPRM.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Union, has issued EASA AD 
2018-0231, dated October 25, 2018 (referred to after this as the 
Mandatory Continuing Airworthiness Information, or ``the MCAI''), to 
correct an unsafe condition for certain Airbus SAS Model A318, A319, 
A320, and A321 series airplanes. The MCAI states:

    The Airworthiness Limitations for the Airbus A320 family 
aeroplanes, which are approved by EASA, are currently defined and 
published in the A318/A319/A320/A321 ALS document(s). The Fuel 
Airworthiness Limitations (FAL) are published in ALS Part 5.
    Failure to accomplish these instructions could result in an 
unsafe condition.
    Previously, EASA issued AD 2017-0169 [which correlates to FAA AD 
2018-17-21, Amendment 39-19375 (83 FR 44209, August 30, 2018) (``AD 
2018-17-21'')] to require accomplishment of all maintenance tasks 
and replacement of life limited parts as described in ALS Part 5 at 
Revision 04.
    Since that [EASA] AD was issued, Airbus published the ALS, 
including new and/or more restrictive requirements, and new A320 
family models were certified and added to the Applicability.
    For the reason described above, this [EASA] AD retains the 
requirements of EASA AD 2017-0169, which is superseded, expands the 
Applicability and requires accomplishment of the actions specified 
in the ALS.

    You may examine the MCAI in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0116.

Relationship Between Proposed AD and AD 2018-17-21

    This NPRM does not propose to supersede AD 2018-17-21. Rather, we 
have determined that a stand-alone AD is more appropriate to address 
the changes in the MCAI. This proposed AD would require revising the 
existing maintenance or inspection program, as applicable, to 
incorporate new or more restrictive fuel airworthiness limitations. 
Accomplishment of the proposed actions would then terminate all of the 
requirements of AD 2018-17-21.

Related Service Information Under 1 CFR Part 51

    Airbus SAS has issued A318/A319/A320/A321 Airworthiness Limitations 
Section (ALS) Part 5 Fuel Airworthiness Limitations (FAL), Revision 05, 
dated June 13, 2018. This service information describes fuel 
airworthiness limitations. This service information is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in the 
ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all the relevant information and determined the unsafe 
condition described previously is likely to exist or develop on other 
products of the same type design.

Proposed Requirements of This NPRM

    This proposed AD would require revising the existing maintenance or

[[Page 7836]]

inspection program, as applicable, to incorporate new or more 
restrictive fuel airworthiness limitations.
    This proposed AD would require revisions to certain operator 
maintenance documents to include new actions (e.g., inspections) and 
Critical Design Configuration Control Limitations (CDCCLs). Compliance 
with these actions and CDCCLs is required by 14 CFR 91.403(c). For 
airplanes that have been previously modified, altered, or repaired in 
the areas addressed by this proposed AD, the operator may not be able 
to accomplish the actions described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must request 
approval for an alternative method of compliance according to paragraph 
(j)(1) of this proposed AD.

Differences Between This Proposed AD and the MCAI or Service 
Information

    The MCAI requires the repetitive replacement of certain components, 
and, for findings from the airworthiness limitations section (ALS) 
inspection tasks, the MCAI requires corrective actions in accordance 
with Airbus maintenance documentation. However, this proposed AD does 
not include those requirements. Operators of U.S.-registered airplanes 
are required by general airworthiness and operational regulations to 
perform maintenance using methods that are acceptable to the FAA. We 
consider those methods to be adequate to address those actions.

Costs of Compliance

    We estimate that this proposed AD affects 1,458 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD.
    We have determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although we recognize that this number may vary from operator to 
operator. In the past, we have estimated that this action takes 1 work-
hour per airplane. Since operators incorporate maintenance or 
inspection program changes for their affected fleet(s), we have 
determined that a per-operator estimate is more accurate than a per-
airplane estimate. Therefore, we estimate the total cost per operator 
to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes and associated appliances to the 
Director of the System Oversight Division.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Airbus SAS: Docket No. FAA-2019-0116; Product Identifier 2018-NM-
152-AD.

(a) Comments Due Date

    We must receive comments by April 19, 2019.

(b) Affected ADs

    This AD affects AD 2018-17-21, Amendment 39-19375 (83 FR 44209, 
August 30, 2018) (``AD 2018-17-21'').

(c) Applicability

    This AD applies to the Airbus SAS airplanes identified in 
paragraphs (c)(1) through (c)(4) of this AD, certificated in any 
category, with an original certificate of airworthiness or original 
export certificate of airworthiness issued on or before June 13, 
2018.
    (1) Model A318-111, -112, -121, and -122 airplanes.
    (2) Model A319-111, -112, -113, -114, -115, -131, -132, and -133 
airplanes.
    (3) Model A320-211, -212, -214, -216, -231, -232, -233, -251N, 
and -271N airplanes.
    (4) Model A321-111, -112, -131, -211, -212, -213, -231, -232, -
251N, -251NX, -252N, -252NX, -253N, -253NX, -271N, -271NX, -272N, 
and -272NX airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Reason

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. We are issuing 
this AD to address the potential of ignition sources inside fuel 
tanks, which, in combination with flammable fuel vapors, could 
result in a fuel tank explosion and consequent loss of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Maintenance or Inspection Program Revision

    Within 90 days after the effective date of this AD, revise the 
existing maintenance or inspection program, as applicable, to 
incorporate the information specified in Airbus A318/A319/A320/A321 
Airworthiness Limitations Section (ALS) Part 5 Fuel Airworthiness 
Limitations (FAL), Revision 05, dated June 13, 2018. The initial 
compliance time for doing the tasks is at the time specified in 
Airbus A318/A319/A320/

[[Page 7837]]

A321 Airworthiness Limitations Section (ALS) Part 5 Fuel 
Airworthiness Limitations (FAL), Revision 05, dated June 13, 2018, 
or within 90 days after the effective date of this AD, whichever 
occurs later.

(h) No Alternative Actions, Intervals, or Critical Design Configuration 
Control Limitations (CDCCLs)

    After the maintenance or inspection program has been revised as 
required by paragraph (g) of this AD, no alternative actions (e.g., 
inspections), intervals, or CDCCLs may be used unless the actions, 
intervals, and CDCCLs are approved as an alternative method of 
compliance (AMOC) in accordance with the procedures specified in 
paragraph (j)(1) of this AD.

(i) Terminating Action for AD 2018-17-21

    Accomplishing the actions required by this AD terminates all 
requirements of AD 2018-17-21.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (k)(2) of this AD. Information 
may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov.
    (i) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (ii) AMOCs approved previously for AD 2018-17-21 are approved as 
AMOCs for the corresponding provisions of this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or the European Aviation 
Safety Agency (EASA); or Airbus SAS's EASA Design Organization 
Approval (DOA). If approved by the DOA, the approval must include 
the DOA-authorized signature.
    (3) Required for Compliance (RC): If any service information 
contains procedures or tests that are identified as RC, those 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the procedures and tests identified as 
RC can be done and the airplane can be put back in an airworthy 
condition. Any substitutions or changes to procedures or tests 
identified as RC require approval of an AMOC.

(k) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) EASA AD 2018-0231, dated October 25, 2018, for related 
information. This MCAI may be found in the AD docket on the internet 
at http://www.regulations.gov by searching for and locating Docket 
No. FAA-2019-0116.
    (2) For more information about this AD, contact Sanjay Ralhan, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3223.
    (3) For service information identified in this AD, contact 
Airbus SAS, Airworthiness Office--EIAS, Rond-Point Emile Dewoitine 
No: 2, 31700 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax 
+33 5 61 93 44 51; email account.airworth-eas@airbus.com; internet 
http://www.airbus.com. You may view this service information at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, 
WA. For information on the availability of this material at the FAA, 
call 206-231-3195.

    Issued in Des Moines, Washington, on February 27, 2019.
Dionne Palermo,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-03830 Filed 3-4-19; 8:45 am]
 BILLING CODE 4910-13-P


