
[Federal Register Volume 84, Number 33 (Tuesday, February 19, 2019)]
[Rules and Regulations]
[Pages 4694-4696]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-02654]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0048; Product Identifier 2018-NE-19-AD; Amendment 
39-19556; AD 2019-03-04]
RIN 2120-AA64


Airworthiness Directives; Engine Alliance Turbofan Engines

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: We are superseding Airworthiness Directive (AD) 2018-11-16 for 
all Engine Alliance (EA) GP7270 and GP7277 turbofan engines with a 
certain engine fan hub assembly. AD 2018-11-16 required a one-time eddy 
current inspection (ECI) of the engine fan hub blade slot bottom and 
blade slot front edge for cracks, a visual inspection of the engine fan 
hub assembly for damage, and removal of parts if damage or defects are 
found that are outside serviceable limits. This AD retains these 
requirements, but expands the population of affected engine fan hub 
assemblies and revises the compliance time for the inspections. This AD 
was prompted by the FAA's determination that inspections need to be 
expanded to all EA GP7270 and GP7277 turbofan engines. We are issuing 
this AD to address the unsafe condition on these products.

DATES: This AD is effective March 6, 2019.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of March 6, 
2019.
    We must receive comments on this AD by April 5, 2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For service information identified in this final rule, contact 
Engine Alliance, 411 Silver Lane, East Hartford, CT 06118; phone: 800-
565-0140; email: help24@pw.utc.com; website: 
www.engineallianceportal.com. You may view this service information at 
the FAA, Engine and Propeller Standards Branch, 1200 District Avenue, 
Burlington, MA 01803. For information on the availability of this 
material at the FAA, call 781-238-7759. It is also available on the 
internet at http://www.regulations.gov by searching for and locating 
Docket No. FAA-2019-0048.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0048; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, the regulatory evaluation, any comments received, and 
other information. The street address for Docket Operations (phone: 
800-647-5527) is listed above. Comments will be available in the AD 
docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Matthew Smith, Aerospace Engineer, ECO 
Branch, FAA, 1200 District Avenue, Burlington, MA, 01803; phone: 781-
238-7735; fax: 781-238-7199; email: matthew.c.smith@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued AD 2018-11-16, Amendment 39-19304 (83 FR 27891, June 15, 
2018), (``AD 2018-11-16''), for certain EA GP7270 and GP7277 turbofan 
engines. AD 2018-11-16 required a one-time ECI of the engine fan hub 
blade slot bottom and blade slot front edge for cracks, a visual 
inspection of the engine fan hub assembly for damage, and removal of 
parts if damage or defects are found that are outside serviceable 
limits. AD 2018-11-16 resulted from an uncontained failure of the 
engine fan hub assembly. We issued AD 2018-11-16 to detect defects, 
damage, and cracks that could result in an uncontained failure of the 
engine fan hub assembly.

Actions Since AD 2018-11-16 was Issued

    Since we issued AD 2018-11-16, we determined that inspections need 
to be expanded to all EA GP7270 and GP7277 turbofan engines with a 
certain engine fan hub assembly because all engines are subject to the 
unsafe condition. As a result, EA published EA Alert Service Bulletin 
(ASB) EAGP7-A72-389, Revision No. 3, dated October 18, 2018, to expand 
the population of engine fan hub assemblies that require inspection. We 
also determined that we could remove the EA GP7272 turbofan engine from 
the Applicability paragraph of this AD because the engine was not 
manufactured. The Applicability paragraph of this AD aligns with the EA 
service information. We are issuing this AD to address the unsafe 
condition on these products.

Related Service Information Under 1 CFR Part 51

    We reviewed EA ASB EAGP7-A72-389, Revision No. 3, dated October 18, 
2018. The ASB describes procedures for ECI and visual inspection of the 
GP7270

[[Page 4695]]

and GP7277 engine fan hub assembly. This service information is 
reasonably available because the interested parties have access to it 
through their normal course of business or by the means identified in 
the ADDRESSES section.

FAA's Determination

    We are issuing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

AD Requirements

    This AD requires a one-time ECI of the GP7270 and GP7277 engine fan 
hub blade slot bottom and blade slot front edge for cracks, a visual 
inspection of the engine fan hub assembly for damage, and removal of 
the engine fan hub assembly if damage or defects are found that are 
outside of serviceable limits.

FAA's Justification and Determination of the Effective Date

    No domestic operators use this product. Therefore, we find good 
cause that notice and opportunity for prior public comment are 
unnecessary. In addition, for the reason stated above, we find that 
good cause exists for making this amendment effective in less than 30 
days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety, and we did not provide you with notice and an opportunity to 
provide your comments before it becomes effective. However, we invite 
you to send any written data, views, or arguments about this final 
rule. Send your comments to an address listed under the ADDRESSES 
section. Include the docket number FAA-2019-0048 and product identifier 
2018-NE-19-AD at the beginning of your comments. We specifically invite 
comments on the overall regulatory, economic, environmental, and energy 
aspects of this final rule. We will consider all comments received by 
the closing date and may amend this final rule because of those 
comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this final rule.

Costs of Compliance

    We estimate that this AD affects zero engines installed on 
airplanes of U.S. registry.
    We estimate the following costs to comply with this AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                       Cost on
                 Action                              Labor cost             Parts cost    Cost per       U.S.
                                                                                          product     operators
----------------------------------------------------------------------------------------------------------------
ECI and visual inspection...............  14 work-hours x $85 per hour =            $0       $1,190           $0
                                           $1,190.
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This AD is issued in accordance with authority delegated by the 
Executive Director, Aircraft Certification Service, as authorized by 
FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the Compliance and Airworthiness Division, but 
during this transition period, the Executive Director has delegated the 
authority to issue ADs applicable to engines, propellers, and 
associated appliances to the Manager, Engine and Propeller Standards 
Branch, Policy and Innovation Division.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends part 39 of the Federal Aviation 
Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Airworthiness Directive (AD) 
2018-11-16, Amendment 39-19304 (83 FR 27891, June 15, 2018) and adding 
the following new AD:

2019-03-04 Engine Alliance: Amendment 39-19556; Docket No. FAA-2019-
0048; Product Identifier 2018-NE-19-AD.

(a) Effective Date

    This AD is effective March 6, 2019.

(b) Affected ADs

    This AD replaces AD 2018-11-16, Amendment 39-19304 (83 FR 27891, 
June 15, 2018).

(c) Applicability

    This AD applies to Engine Alliance (EA) GP7270 and GP7277 model 
turbofan engines with engine fan hub assembly, part number (P/N) 
5760221 or P/N 5760321, installed.

[[Page 4696]]

(d) Subject

    Joint Aircraft System Component (JASC) Code 7230, Turbine Engine 
Compressor Section.

(e) Unsafe Condition

    This AD was prompted by the FAA's determination that inspections 
need to be expanded to all EA GP7270 and GP7277 turbofan engines. We 
are issuing this AD to detect defects, damage, and cracks that could 
result in an uncontained failure of the engine fan hub assembly. The 
unsafe condition, if not addressed, could result in uncontained 
failure of the engine fan hub assembly, damage to the engine, and 
damage to the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Within 3,000 cycles since new after the effective date of this 
AD, or by August 15, 2019, whichever is later:
    (1) For engine fan hubs at the low-pressure compressor (LPC) 
module assembly level:
    (i) Perform a visual inspection of the engine fan hub assembly, 
in accordance with the Accomplishment Instructions, For Fan Hubs at 
LPC Module Assembly Level, paragraphs 1.A.(1), 1.A.(4), and 
1.A.(6)(a), of EA ASB EAGP7-A72-389, Revision No. 3, dated October 
18, 2018.
    (ii) Perform an eddy current inspection (ECI) of the engine fan 
hub blade slot bottoms and front edges, in accordance with the 
Accomplishment Instructions, For Fan Hubs at LPC Module Assembly 
Level, paragraphs 2.A and 2.B, of EA ASB EAGP7-A72-389, Revision No. 
3, dated October 18, 2018.
    (2) For engine fan hub assemblies at the piece part level:
    (i) Perform a visual inspection of the engine fan hub assembly, 
in accordance with the Accomplishment Instructions, For Fan Hubs at 
Piece Part Level, paragraphs 1.A.(1) and 1.A.(3), of EA ASB EAGP7-
A72-389, Revision No. 3, dated October 18, 2018.
    (ii) Perform an ECI of the engine fan hub blade slot bottoms and 
front edges, in accordance with the Accomplishment Instructions, For 
Fan Hubs at Piece Part Level, paragraphs 2.A and 2.B, of EA ASB 
EAGP7-A72-389, Revision No. 3, dated October 18, 2018.
    (3) For engine fan hub assemblies installed in an engine (on-
wing or off-wing):
    (i) Perform a visual inspection of the engine fan hub assembly, 
in accordance with the Accomplishment Instructions, For Fan Hubs 
Installed in an Engine, paragraphs 1.C.(1), 1.C.(5), and 1.C.(7)(a), 
of EA ASB EAGP7-A72-389, Revision No. 3, dated October 18, 2018.
    (ii) Perform an ECI of the engine fan hub blade slot bottoms and 
front edges, in accordance with the Accomplishment Instructions, For 
Fan Hubs Installed in an Engine, paragraphs 1.D.(1) and 1.D.(2), of 
EA ASB EAGP7-A72-389, Revision No. 3, dated October 18, 2018.
    (4) If the engine fan hub assembly visual inspection reveals 
defects or damage to the engine fan hub assembly that are found 
outside the serviceable limits specified in Table 6 in the 
Accomplishment Instructions of EA ASB EAGP7-A72-389, Revision No. 3, 
dated October 18, 2018, remove the engine fan hub assembly from 
service and replace with a part that is eligible for installation, 
before further flight.
    (5) If the engine fan hub assembly ECI results in a rejectable 
indication, per the Appendix, Added Data, of EA ASB EAGP7-A72-389, 
Revision No. 3, dated October 18, 2018, remove the engine fan hub 
assembly from service and replace with a part that is eligible for 
installation, before further flight.

(h) Credit for Previous Actions

    You may take credit for the inspection required by paragraph (g) 
of this AD if you performed the inspection before the effective date 
of this AD, using EA ASB EAGP7-A72-389, Original Issue, dated 
December 19, 2017; EA ASB EAGP7-A72-389, Revision No. 1, dated 
January 19, 2018; or EA ASB EAGP7-A72-389, Revision No. 2, dated 
April 17, 2018.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, ECO Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or local Flight Standards District Office, as 
appropriate. If sending information directly to the manager of the 
certification office, send it to the attention of the person 
identified in paragraph (j) of this AD. You may email your request 
to: ANE-AD-AMOC@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) AMOCs approved for AD 2018-11-16 (83 FR 27891, June 15, 
2018) are approved as AMOCs for the corresponding provisions of this 
AD.

(j) Related Information

    For more information about this AD, contact Matthew Smith, 
Aerospace Engineer, ECO Branch, FAA, 1200 District Avenue, 
Burlington, MA, 01803; phone: 781-238-7735; fax: 781-238-7199; 
email: matthew.c.smith@faa.gov.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Engine Alliance (EA) Alert Service Bulletin EAGP7-A72-389, 
Revision No. 3, dated October 18, 2018.
    (ii) [Reserved]
    (3) For EA service information identified in this AD, contact 
Engine Alliance, 411 Silver Lane, East Hartford, CT, 06118; phone: 
800-565-0140; email: help24@pw.utc.com; website: 
www.engineallianceportal.com.
    (4) You may view this service information at FAA, Engine and 
Propeller Standards Branch, 1200 District Avenue, Burlington, MA, 
01803. For information on the availability of this material at the 
FAA, call 781-238-7759.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Burlington, Massachusetts, on February 12, 2019.
Robert J. Ganley,
Manager, Engine & Propeller Standards Branch, Aircraft Certification 
Service.
[FR Doc. 2019-02654 Filed 2-15-19; 8:45 am]
 BILLING CODE 4910-13-P


