
[Federal Register Volume 83, Number 237 (Tuesday, December 11, 2018)]
[Rules and Regulations]
[Pages 63561-63565]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: R1-2018-26365]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2018-0960; Product Identifier 2018-NM-151-AD; Amendment 
39-19512; AD 2018-23-51]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

    Editorial Note: Rule document 2018-26365 was originally 
published on pages 62697 through 62700 in the issue of Thursday, 
December 6, 2018. In that publication, on page 62700, in Figure 2 to 
paragraph (h), the last sentence in the table was inadvertently 
truncated. The corrected document is published here in its entirety.

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for all The 
Boeing Company Model 737-8 and -9 airplanes. This emergency AD was sent 
previously to all known U.S. owners and operators of these airplanes. 
This AD requires revising certificate limitations and operating 
procedures of the airplane flight manual (AFM) to provide the flight 
crew with runaway horizontal stabilizer trim procedures to follow under 
certain conditions. This AD was prompted by analysis performed by the 
manufacturer showing that if an erroneously high single angle of attack 
(AOA) sensor input is received by the flight control system, there is a 
potential for repeated nose-down trim commands of the horizontal 
stabilizer. We are issuing this AD to address the unsafe condition on 
these products.

DATES: This AD is effective December 21, 2018 to all persons except 
those persons to whom it was made immediately effective by Emergency AD 
2018-23-51, issued on November 7, 2018, which contained the 
requirements of this amendment.
    We must receive comments on this AD by January 22, 2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0960; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    The AD docket contains this final rule, the regulatory evaluation, 
any comments received, and other information. The street address for 
Docket Operations (phone: 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Douglas Tsuji, Senior Aerospace 
Engineer, Systems and Equipment Section, FAA, Seattle ACO Branch, 2200 
South 216th St., Des Moines, WA 98198; phone and fax: 206-231-3548; 
email: Douglas.Tsuji@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

    On November 7, 2018, we issued Emergency AD 2018-23-51, which 
requires revising certificate limitations and operating procedures of 
the AFM to provide the flight crew with runaway horizontal stabilizer 
trim procedures to follow under certain conditions. This emergency AD 
was sent previously to all known U.S. owners and operators of these 
airplanes. This action was prompted by analysis performed by the 
manufacturer showing that if an erroneously high single AOA sensor 
input is received by the flight control system, there is a potential 
for repeated nose-down trim commands of the horizontal stabilizer. This 
condition, if not addressed, could cause the flight crew to have 
difficulty controlling the airplane, and lead to excessive nose-down 
attitude, significant altitude loss, and possible impact with terrain.

FAA's Determination

    We are issuing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

AD Requirements

    This AD requires revising certificate limitations and operating 
procedures of the AFM to provide the flight crew with runaway 
horizontal stabilizer trim procedures to follow under certain 
conditions.

[[Page 63562]]

Interim Action

    We consider this AD interim action. If final action is later 
identified, we might consider further rulemaking then.

FAA's Determination of the Effective Date

    An unsafe condition exists that requires the immediate adoption of 
Emergency AD 2018-23-51, issued on November 7, 2018, to all known U.S. 
owners and operators of these airplanes. The FAA found that the risk to 
the flying public justified waiving notice and comment prior to 
adoption of this rule because an erroneously high single AOA sensor 
input received by the flight control system can result in a potential 
for repeated nose-down trim commands of the horizontal stabilizer, 
which could cause the flight crew to have difficulty controlling the 
airplane, and lead to excessive nose-down attitude, significant 
altitude loss, and possible impact with terrain. These conditions still 
exist and the AD is hereby published in the Federal Register as an 
amendment to section 39.13 of the Federal Aviation Regulations (14 CFR 
39.13) to make it effective to all persons.
    Therefore, we find good cause that notice and opportunity for prior 
public comment are impracticable. In addition, for the reason(s) stated 
above, we find that good cause exists for making this amendment 
effective in less than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety and was not preceded by notice and an opportunity for public 
comment. However, we invite you to send any written data, views, or 
arguments about this final rule. Send your comments to an address 
listed under the ADDRESSES section. Include the docket number FAA-2018-
0960 and Product Identifier 2018-NM-151-AD at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this final rule. We will 
consider all comments received by the closing date and may amend this 
final rule because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this final rule.

Costs of Compliance

    We estimate that this AD affects 45 airplanes of U.S. registry. We 
estimate the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
                Action                         Labor cost           Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Revising the AFM......................  1 work-hour x $85 per                 $0             $85          $3,825
                                         hour = $85.
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation Programs'' 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This AD is issued in accordance with authority delegated by the 
Executive Director, Aircraft Certification Service, as authorized by 
FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the Compliance and Airworthiness Division, but 
during this transition period, the Executive Director has delegated the 
authority to issue ADs applicable to transport category airplanes and 
associated appliances to the Director of the System Oversight Division.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2018-23-51 The Boeing Company: Amendment 39-19512; Docket No. FAA-
2018-0960; Product Identifier 2018-NM-151-AD.

(a) Effective Date

    This AD is effective December 21, 2018 to all persons except 
those persons to whom it was made immediately effective by Emergency 
AD 2018-23-51, issued on November 7, 2018, which contained the 
requirements of this amendment.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all The Boeing Company Model 737-8 and -9 
airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 27, Flight 
controls.

[[Page 63563]]

(e) Unsafe Condition

    This AD was prompted by analysis performed by the manufacturer 
showing that if an erroneously high single angle of attack (AOA) 
sensor input is received by the flight control system, there is a 
potential for repeated nose-down trim commands of the horizontal 
stabilizer. We are issuing this AD to address this potential 
resulting nose-down trim, which could cause the flight crew to have 
difficulty controlling the airplane, and lead to excessive nose-down 
attitude, significant altitude loss, and possible impact with 
terrain.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Revision of Airplane Flight Manual (AFM): Certificate Limitations

    Within 3 days after the effective date of this AD, revise the 
Certificate Limitations chapter of the applicable AFM to include the 
information in figure 1 to paragraph (g) of this AD.
BILLING CODE 1301-00-D
[GRAPHIC] [TIFF OMITTED] TR11DE18.004

(h) AFM Revision: Operating Procedures

    Within 3 days after the effective date of this AD, revise the 
Operating Procedures chapter of the applicable AFM to include the 
information in figure 2 to paragraph (h) of this AD.

[[Page 63564]]

[GRAPHIC] [TIFF OMITTED] TR11DE18.005

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO Branch, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or local Flight Standards District 
Office, as appropriate. If sending information directly to the 
manager of the certification office, send it to the attention of the 
person identified in paragraph (j) of this AD. Information may be 
emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.

(j) Related Information

    For more information about this AD, contact Douglas Tsuji, 
Senior Aerospace Engineer, Systems and Equipment Section, FAA, 
Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; 
phone and fax: 206-231-3548; email: Douglas.Tsuji@faa.gov.

(k) Material Incorporated by Reference

    None.


[[Page 63565]]


    Issued in Des Moines, Washington, on November 21, 2018.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. R1-2018-26365 Filed 12-7-18; 2:00 pm]
 BILLING CODE 1301-00-C


