[Federal Register Volume 83, Number 179 (Friday, September 14, 2018)]
[Proposed Rules]
[Pages 46670-46676]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2018-19759]



[[Page 46670]]

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2018-0790; Product Identifier 2018-NM-078-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc., Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to supersede Airworthiness Directive (AD) 2010-14-
05, which applies to certain Bombardier, Inc., Model CL-600-1A11 (600), 
CL-600-2A12 (601), and CL-600-2B16 (601-3A, 601-3R, and 604 Variants) 
airplanes. AD 2010-14-05 requires inspection for the part numbers of 
the system and brake accumulators, and repetitive replacement of 
affected accumulators. Since we issued AD 2010-14-05, we have 
determined that new or more restrictive airworthiness limitations, as 
well as additional actions, are necessary to address the unsafe 
condition. In addition to the requirements of AD 2010-14-05, this 
proposed AD would require relocating the accumulators and revising the 
maintenance or inspection program to incorporate new or more 
restrictive airworthiness limitations. This proposed AD would also add 
optional terminating action for certain airplanes. We are proposing 
this AD to address the unsafe condition on these products.

DATES: We must receive comments on this proposed AD by October 29, 
2018.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec 
H4S 1Y9, Canada; Widebody Customer Response Center North America toll-
free telephone 1-866-538-1247 or direct-dial telephone 1-514-855-2999; 
fax 514-855-7401; email [email protected]; internet http://www.bombardier.com. You may view this referenced service information at 
the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, 
WA. For information on the availability of this material at the FAA, 
call 206-231-3195.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0790; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this NPRM, the regulatory evaluation, any comments received, 
and other information. The street address for the Docket Operations 
office (telephone 800-647-5527) is in the ADDRESSES section. Comments 
will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Neil Doh, Aerospace Engineer, Aviation 
Safety Section AIR-7B1, Boston ACO Branch, FAA, 1200 District Avenue, 
Burlington, MA 01803; telephone 781-238-7757.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2018-0790; 
Product Identifier 2018-NM-078-AD'' at the beginning of your comments. 
We specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this proposed AD. We will consider 
all comments received by the closing date and may amend this proposed 
AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    We issued AD 2010-14-05, Amendment 39-16350 (75 FR 37994, July 1, 
2010) (``AD 2010-14-05''), for certain Bombardier Model CL-600-1A11 
(600), CL-600-2A12 (601), CL-600-2B16 (601-3A, 601-3R, and 604 Variants 
(including CL-605 Marketing Variant)) airplanes. AD 2010-14-05 requires 
an inspection to determine the part numbers of the system accumulators 
numbers 1, 2, and 3 and brake accumulators numbers 2 and 3, and 
repetitive replacement of the accumulator. AD 2010-14-05 resulted from 
reports of the on-ground failure of the hydraulic accumulator screw cap 
or end cap, resulting in loss of the associated hydraulic system and 
high-energy impact damage to adjacent systems and structure. We issued 
AD 2010-14-05 to address failure of one of the brake accumulator screw 
caps/end caps, resulting in impact damage causing loss of both 
hydraulic systems No. 2 and No. 3, with consequent loss of both braking 
and nose wheel steering and the potential for a runway excursion.

Actions Since AD 2010-14-05 Was Issued

    Since we issued AD 2010-14-05, we have determined that new or more 
restrictive airworthiness limitations and additional actions are 
necessary to address the unsafe condition.
    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian AD CF-2009-39R1, issued 
October 13, 2017 (referred to after this as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for certain Bombardier, Inc., Model CL-600-1A11 (600), CL-
600-2A12 (601), and CL-600-2B16 (601-3A, 601-3R, and 604 Variants) 
airplanes. The MCAI states:

    Seven cases of on-ground hydraulic accumulator screw cap or end 
cap failure have been experienced on CL-600-2B19 (CRJ) aircraft, 
resulting in loss of the associated hydraulic system and high-energy 
impact damage to adjacent systems and structure. The lowest number 
of flight cycles accumulated at the time of failure, to date, has 
been 6991 flight cycles.
    Although there have been no failures to date on any CL-600-1A11, 
CL-600-2A12 or CL-600-2B16 aircraft, the same accumulators as those 
installed on the CL-600-2B19, Part Numbers (P/N) 08-60163-002 and 
08-60164-002 are installed on some of the aircraft listed in the 
Applicability section of this directive.
    Notes:
    1. Earlier accumulators, P/Ns 2770571-102, 2770571-103, 2770571-
104 and 2770571-105, were installed in production on the following 
aircraft: CL-600-1A11 [all Serial Numbers (S/Ns)], CL-600-2A12 (all 
S/Ns) and CL-600-2B16 (S/Ns 5001 through 5194 and 5301 through 5524 
only). These accumulators do not require inspection or replacement. 
However, if any of the accumulators with the above P/Ns have been 
replaced in-service by P/Ns 08-60163-002 and 08-60164-002, these 
latter accumulators require replacement.
    2. Prior to issuance of [Canadian] AD CF-2009-39, the only 
accumulators ever installed in production on CL-600-2B16

[[Page 46671]]

aircraft, S/Ns 5525 through 5665 and 5701 through 5908, are P/Ns 08-
60163-002 and 08-60164-002; these accumulators require replacement.
    3. After issuance of [Canadian] AD CF-2009-39 [which 
corresponded to FAA AD 2010-14-05, Amendment 39-16350 (75 FR 37994, 
July 1, 2010)], accumulators with P/Ns specified in Note 2, above, 
began to feature various S/N suffixes. Only accumulators with S/N 
suffix ``TNAE'' do not require replacement, but they are subject to 
other mandatory actions detailed in this AD.
    4. Stainless steel accumulators P/Ns 601R75139-3 (11094-4) and 
601R75139-1 (11093-4) were installed in production on CL-600-2B16 
aircraft, S/Ns 5909 and subsequent. These accumulators do not 
require replacement, but they are subjected to other mandatory 
actions detailed in this AD.
    A detailed analysis of the systems and structure in the 
potential line of trajectory of a failed screw cap/end cap for each 
accumulator, P/Ns 08-60163-002 and 08-60164-002, has been conducted. 
On the Challengers, it has been identified that the worst case 
scenario would be a failure of system No. 1, 2 or 3 accumulator 
screw caps/end caps (depending on the model), resulting in a 
potential uncontrolled fire in a non-designated fire zone.
    The original version of this [Canadian] AD gave instructions to 
perform identification and records checks, where applicable, and 
replace accumulators, P/Ns 08-60163-002 and 08-60164-002 within the 
time compliance specified.
* * * * *
    The unsafe condition is potential impact damage that could cause 
loss of both hydraulic systems No. 2 and No. 3, and the consequent loss 
of both braking and nose wheel steering, the potential for a runway 
excursion, and damage to the airplane. Required actions include 
relocating certain accumulators. You may examine the MCAI in the AD 
docket on the internet at http://www.regulations.gov by searching for 
and locating Docket No. FAA-2018-0790.

Related Service Information Under 1 CFR Part 51

    The following Bombardier service information describes procedures 
for replacing hydraulic system accumulators with new, overhauled, or 
refurbished accumulators. These documents are distinct since they apply 
to different airplane models.

 Service Bulletin 600-742, Revision 4, dated June 11, 2015
 Service Bulletin 601-597, Revision 4, dated June 11, 2015
 Service Bulletin 604-29-008, Revision 4, dated June 11, 2015
 Service Bulletin 605-29-001, Revision 4, dated June 10, 2015

    The following Bombardier service information describes procedures 
for relocating hydraulic system accumulators. These documents are 
distinct since they apply to different airplane models in different 
configurations.

 Service Bulletin 600-0764, dated October 8, 2015
 Service Bulletin 600-0767, dated August 25, 2016
 Service Bulletin 601-0633, dated October 8, 2015
 Service Bulletin 601-0637, dated August 25, 2016
 Service Bulletin 604-29-013, Revision 2, dated April 18, 2016
 Service Bulletin 605-29-006, Revision 2, dated April 19, 2016

    The following Bombardier Time Limits/Maintenance Checks describe 
certain systems life limits of the safe life items. These documents are 
distinct since they apply to different airplane models in different 
configurations.

 Bombardier Challenger 600 Time Limits/Maintenance Checks, PSP 
605, Revision 39, dated January 8, 2018
 Bombardier Challenger 601 Time Limits/Maintenance Checks, PSP 
601-5, Revision 46, dated January 8, 2018
 Bombardier Challenger 601 Time Limits/Maintenance Checks, PSP 
601A-5, Revision 42, dated January 8, 2018
 Bombardier Challenger 604 CL-604 Time Limits/Maintenance 
Checks, Revision 30, dated December 4, 2017
 Bombardier Challenger CL-605 Time Limits/Maintenance Checks, 
Revision 18, dated December 4, 2017

    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type designs.
    This proposed AD would require revisions to certain operator 
maintenance documents to include new actions (e.g., inspections). 
Compliance with these actions is required by 14 CFR 91.403(c). For 
airplanes that have been previously modified, altered, or repaired in 
the areas addressed by this proposed AD, the operator may not be able 
to accomplish the actions described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must request 
approval for an alternative method of compliance according to paragraph 
(n)(1) of this proposed AD. The request should include a description of 
changes to the required inspections that will ensure the continued 
operational safety of the airplane.

Difference Between Proposed AD and MCAI

    Although the MCAI placed no restrictions on special flight permits, 
this proposed AD would limit ferry flights by requiring an engineering 
recommendation from Bombardier as well as approval from the Flight 
Standards District Office. This difference has been coordinated with 
TCCA.

Costs of Compliance

    We estimate that this proposed AD affects 130 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
            Labor cost                  Parts cost         Cost per product         Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Retained actions: 20 work-hours x  $7,717..............  $9,417.............  $1,224,210.
 $85 per hour = $,1,700.
New actions: Up to 170 work-hours  Up to $41,635.......  Up to $56,085......  Up to $7,291,050.
 x $85 per hour = Up to $14,450.
----------------------------------------------------------------------------------------------------------------


[[Page 46672]]

    For the new maintenance/inspection program revision, we have 
determined that this action takes an average of 90 work-hours per 
operator, although we recognize that this number may vary from operator 
to operator. In the past, we have estimated that this action takes 1 
work-hour per airplane. Since operators incorporate maintenance or 
inspection program changes for their affected fleet, we have determined 
that a per-operator estimate is more accurate than a per-airplane 
estimate. Therefore, we estimate the total cost per operator to be 
$7,650 (90 work-hours x $85 per work-hour).
    According to the manufacturer, some or all of the costs of this 
proposed AD may be covered under warranty, thereby reducing the cost 
impact on affected individuals. We do not control warranty coverage for 
affected individuals. As a result, we have included all known costs in 
our cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes to the Director of the System Oversight 
Division.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866,
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    3. Will not affect intrastate aviation in Alaska, and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by removing Airworthiness Directive (AD) 
2010-14-05, Amendment 39-16350 (75 FR 37994, July 1, 2010), and adding 
the following new AD:

Bombardier, Inc.: Docket No. FAA-2018-0790; Product Identifier 2018-
NM-078-AD.

(a) Comments Due Date

    We must receive comments by October 29, 2018.

(b) Affected ADs

    This AD replaces AD 2010-14-05, Amendment 39-16350 (75 FR 37994, 
July 1, 2010) (``AD 2010-14-05'').

(c) Applicability

    This AD applies to the Bombardier, Inc., airplanes, certificated 
in any category, identified in paragraphs (c)(1) through (c)(5) of 
this AD.
    (1) Model CL-600-1A11 (600) airplanes, serial numbers 1004 
through 1085 inclusive.
    (2) Model CL-600-2A12 (601) airplanes, serial numbers 3001 
through 3066 inclusive.
    (3) Model CL-600-2B16 airplanes (601-3A Variant), serial numbers 
5001 through 5134 inclusive.
    (4) Model CL-600-2B16 airplanes (601-3R Variant), serial numbers 
5135 through 5194 inclusive.
    (5) Model CL-600-2B16 airplanes (604 Variant), serial numbers 
5301 through 5665 inclusive and 5701 and subsequent.

    Note 1 to paragraph (c) of this AD: Certain Model CL-600-2B16 
(604 Variant) airplanes might be referred to by the marketing 
designation CL-605.

(d) Subject

    Air Transport Association (ATA) of America Code 29, Hydraulic 
power.

(e) Reason

    This AD was prompted by reports of on-ground hydraulic 
accumulator screw cap or end cap failure that resulted in the loss 
of the associated hydraulic system and high-energy impact damage to 
adjacent systems and structure. We are issuing this AD to address 
failure of one of the brake accumulator screw caps/end caps, which 
could result in impact damage causing loss of both hydraulic systems 
No. 2 and No. 3, and the consequent loss of both braking and nose 
wheel steering, the potential for a runway excursion, and damage to 
the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Retained Part Number Inspection and Accumulator Replacement, With 
Revised Formatting, Service Information, and Affected Part Numbers

    This paragraph restates the requirements of paragraph (g) of AD 
2010-14-05, with revised formatting, service information, and 
affected part numbers. Do the following actions as applicable.
    (1) Within 50 flight hours after August 5, 2010 (the effective 
date of AD 2010-14-05), inspect to determine the part numbers of the 
system accumulators numbers 1, 2, and 3, and brake accumulators 
numbers 2 and 3 that are installed on the airplane. A review of 
airplane maintenance records is acceptable in lieu of this 
inspection if the part number of each accumulator can be 
conclusively determined from that review. If all of the installed 
accumulators have part number (P/N) 2770571-102, 2770571-103, 
2770571-104, 2770571-105, 601R75139-3 (11094-4), or 601R75139-1 
(11093-4), no further action is required by paragraph (g) of this 
AD.
    (2) Except as provided in paragraph (g)(1) of this AD: At the 
applicable time in paragraph (g)(2)(i), (g)(2)(ii), or (g)(2)(iii) 
of this AD, replace the accumulator with a new, overhauled, or 
refurbished accumulator with the same part number, in accordance 
with the Accomplishment Instructions of the applicable service 
bulletin listed in figure 1 to paragraphs (g)(2) and (g)(3) of this 
AD.
    (i) For each accumulator having P/Ns 08-60163-002 (601R75138-1), 
and 08-60164-002 (601R75138-3), as applicable, that has accumulated 
more than 3,650 total flight cycles as of August 5, 2010 (the 
effective date of AD 2010-14-05): Replace the accumulator within 100 
flight cycles after August 5, 2010.
    (ii) For each accumulator having P/N 08-60163-002 (601R75138-1), 
and 08-60164-002 (601R75138-3), as applicable, that has accumulated 
3,650 total flight cycles or fewer

[[Page 46673]]

as of August 5, 2010: Replace the accumulator before the 
accumulation of 3,750 total flight cycles on the accumulator.
    (iii) For each accumulator having P/N 08-60163-002 (601R75138-
1), and 08-60164-002 (601R75138-3), as applicable, for which it is 
not possible to determine the number of flight cycles accumulated: 
Replace the accumulator within 100 flight cycles after August 5, 
2010.
[GRAPHIC] [TIFF OMITTED] TP14SE18.000

    (3) Thereafter, before the accumulation of 3,750 total flight 
cycles on any accumulator having P/Ns 08-60163-002 (601R75138-1), 
and 08-60164-002 (601R75138-3), as applicable, replace the 
accumulator with a new, overhauled, or refurbished accumulator 
having the same part number, in accordance with the Accomplishment 
Instructions of the applicable service bulletin listed in figure 1 
to paragraphs (g)(2) and (g)(3) of this AD.

(h) New Provision of This AD: Terminating Action for Certain 
Accumulators

    For each accumulator with one of the following part number and 
serial number (S/N) suffixes, the repetitive replacement specified 
in paragraphs (g)(2) and (g)(3) of this AD is not required.

(1) P/N 08-60163-002 with S/N suffix TNAE
(2) P/N 08-601-002 with S/N suffix TNAE
(3) P/N 601R75139-3 (11094-4)
(4) P/N 601R75139-1 (11093-4)

(i) New Requirement of This AD: Relocation of Accumulators

    Within 60 months or 2,400 flight cycles, whichever occurs first 
after the effective date of this AD, relocate the hydraulic system 
accumulators as specified in paragraphs (i)(1) through (i)(4) of 
this AD, as applicable. Relocation of the hydraulic system 
accumulators as required by this paragraph does not terminate any 
repetitive replacement required by paragraph (g)(2) or (g)(3) of 
this AD.
    (1) For Model CL-600-1A11 (600) airplanes, S/Ns 1004 through 
1085 inclusive: Relocate accumulators as specified in paragraphs 
(i)(1)(i) and (i)(1)(ii) of this AD.
    (i) Relocate hydraulic system Nos. 1 and 2 accumulators, in 
accordance with the Accomplishment Instructions of Bombardier 
Service Bulletin 601-0764, dated October 8, 2015.
    (ii) Relocate hydraulic system No. 3 accumulator, in accordance 
with the Accomplishment Instructions of Bombardier Service Bulletin 
600-0767, dated August 25, 2016.
    (2) For Model CL-600-2A12 (601) airplanes, S/Ns 3001 through 
3066 inclusive, and Model CL-600-2B16 (601-3A and 601-3R Variants) 
airplanes, S/Ns 5001 through 5194 inclusive: Relocate accumulators 
as specified in paragraphs (i)(2)(i) and (i)(2)(ii) of this AD.
    (i) Relocate hydraulic system Nos. 1 and 2 accumulators, in 
accordance with the Accomplishment Instructions of Bombardier 
Service Bulletin 601-0633, dated October 8, 2015.
    (ii) Relocate hydraulic system No. 3 accumulator, in accordance 
with the Accomplishment Instructions of Bombardier Service Bulletin 
601-0637, dated August 25, 2016.
    (3) For Model CL-600-2B16 (604 Variant) airplanes, S/Ns 5301 
through 5665 inclusive: Relocate hydraulic system No. 3 accumulator, 
in accordance with the Accomplishment Instructions of Bombardier 
Service Bulletin 604-29-013, Revision 2, dated April 18, 2016.
    (4) For Model CL-600-2B16 (605) airplanes, S/Ns 5701 and 
subsequent (i.e., Model CL-600-2B16 (604 Variant), referred to by 
the marketing designation CL-605): Relocate hydraulic system No. 3 
accumulator, in accordance with the Accomplishment Instructions of 
Bombardier Service Bulletin 605-29-006, Revision 2, dated April 19, 
2016.

(j) New Requirement of This AD: Revision of Maintenance/Inspection 
Program

    Within 50 flight hours after the effective date of this AD, 
revise the maintenance or inspection program, as applicable, to 
incorporate the tasks specified in figure 2 to paragraph (j) of this 
AD.

[[Page 46674]]

[GRAPHIC] [TIFF OMITTED] TP14SE18.001

(k) No Alternative Actions or Intervals

    After the maintenance or inspection program has been revised as 
required by paragraph (j) of this AD, no alternative actions (e.g., 
inspections) or intervals may be used unless the actions or 
intervals are approved as an alternative method of compliance (AMOC) 
in accordance with the procedures specified in paragraph (n)(1) of 
this AD.

(l) Credit for Previous Actions

    (1) Replacement of an accumulator with a new accumulator having 
the same part number is also acceptable for compliance with the 
requirements of paragraphs (g)(2) and (g)(3) of this AD, if done 
before August 5, 2010 (the effective date of AD 2010-14-05), in 
accordance with the applicable service bulletin listed in figure 3 
to paragraph (l)(1) of this AD. This service information is not 
incorporated by reference in this AD.

[[Page 46675]]

[GRAPHIC] [TIFF OMITTED] TP14SE18.002

    (2) Replacement of an accumulator with a new accumulator having 
the same part number is also acceptable for compliance with the 
requirements of paragraphs (g)(2) and (g)(3) of this AD, if done 
before the effective date of this AD in accordance with the 
applicable service bulletin listed in figure 4 to paragraph (l)(2) 
of this AD. This service information is not incorporated by 
reference in this AD.

[[Page 46676]]

[GRAPHIC] [TIFF OMITTED] TP14SE18.003

    (3) This paragraph provides credit for actions required by 
paragraph (i)(3) of this AD, if those actions were performed before 
the effective date of this AD, in accordance with Bombardier Service 
Bulletin 604-29-013, dated April 30, 2015; or Bombardier Service 
Bulletin 604-29-013, Revision 1, dated October 19, 2015. This 
service information is not incorporated by reference in this AD.
    (4) This paragraph provides credit for actions required by 
paragraph (i)(4) of this AD, if those actions were performed before 
the effective date of this AD, in accordance with Bombardier Service 
Bulletin 605-29-006, dated April 30, 2015; or Bombardier Service 
Bulletin 605-29-006, Revision 1, dated October 19, 2015. This 
service information is not incorporated by reference in this AD.

(m) Special Flight Permit

    Special flight permits may be issued in accordance with sections 
21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 
and 21.199) to operate the airplane to a location where the airplane 
can be modified, provided the following conditions are met:
    (1) An engineering recommendation must be obtained via the 
Bombardier process Service Request for Product Support Action 
(SRPSA) at [email protected].
    (2) Approval of the special flight permit must be obtained from 
the Flight Standards District Office.

(n) Other FAA AD Provisions

    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York ACO Branch, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or local Flight Standards District Office, as appropriate. 
If sending information directly to the manager of the certification 
office, send it to ATTN: Program Manager, Continuing Operational 
Safety, FAA, New York ACO Branch.
    (i) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (ii) AMOC 15-76R1 and AMOC 15-53, approved previously for AD 
2010-14-05, are approved as AMOCs for the corresponding provisions 
of paragraph (g)(2) of this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO 
Branch, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier's TCCA Design Approval Organization (DAO). If approved by 
the DAO, the approval must include the DAO-authorized signature.

(o) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian AD CF-2009-39R1, dated October 13, 2017, for related 
information. This MCAI may be found in the AD docket on the internet 
at http://www.regulations.gov by searching for and locating Docket 
No. FAA-2018-0790.
    (2) For more information about this AD, contact Neil Doh, 
Aerospace Engineer, Aviation Safety Section AIR-7B1, Boston ACO 
Branch, FAA, 1200 District Avenue, Burlington, MA 01803; telephone 
781-238-7757.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; Widebody Customer Response Center 
North America toll-free telephone 1-866-538-1247 or direct-dial 
telephone 1-514-855-2999; fax 514-855-7401; email 
[email protected]; internet http://www.bombardier.com. You 
may view this service information at the FAA, Transport Standards 
Branch, 2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195.

    Issued in Des Moines, Washington, on August 24, 2018.
James Cashdollar,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2018-19759 Filed 9-13-18; 8:45 am]
 BILLING CODE 4910-13-P


