[Federal Register Volume 83, Number 111 (Friday, June 8, 2018)]
[Rules and Regulations]
[Pages 26564-26566]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2018-12270]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2018-0507; Product Identifier 2018-NM-027-AD; Amendment 
39-19308; AD 2018-12-04]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
The Boeing Company Model 777-300ER series airplanes. This AD requires 
replacing the water filter assembly in certain steam ovens. This AD was 
prompted by a report that water can enter the steam oven cavity and 
become heated and then released when the oven door is opened. We are 
issuing this AD to address the unsafe condition on these products.

DATES: This AD is effective June 25, 2018.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of June 25, 
2018.
    We must receive comments on this AD by July 23, 2018.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this final rule, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110 SK57, Seal Beach, CA 90740-5600; 
telephone 562 797 1717; internet https://www.myboeingfleet.com. You may 
view this service information at the FAA, Transport Standards Branch, 
2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195. It is also 
available on the internet at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2018-0507.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0507; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, the regulatory evaluation, any comments received, and 
other information. The street address for Docket Operations (phone: 
800-647-5527) is in the ADDRESSES section. Comments will be available 
in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Stanley Chen, Aerospace Engineer, 
Cabin Safety and Environmental Systems Section, FAA, Seattle ACO 
Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206-
231-3565; email: [email protected].

SUPPLEMENTARY INFORMATION:

Discussion

    We have received a report that members of the cabincrew on a Model 
787 airplane were injured when hot

[[Page 26565]]

water escaped during the opening of the steam oven door. The incident 
occurred with Jamco steam ovens, part number (P/N) ASN2001-1 and P/N 
ASN2001-12. Investigation revealed that the current water filter 
configuration allows foreign objects to enter the water system, which 
can prevent the solenoid valve from moving to a fully closed position 
and subsequently allow water to enter the steam oven cavity. Water in 
the steam oven cavity can become heated and then released when the door 
is opened. A new water filter assembly has been developed, which 
includes a larger screen to prevent foreign object debris from moving 
downstream to block the solenoid valve from moving to a fully closed 
position. This condition, if not addressed, could result in water 
becoming heated as it collects in the bottom of the oven during the 
cooking cycle, resulting in hot water escaping when the oven door is 
opened, and subsequent injury to the cabincrew.
    The Jamco steam ovens installed on Model 777-300ER series airplanes 
have the same part numbers as those installed on the affected Model 787 
airplane; therefore, Model 777-300ER series airplanes are subject to 
the same unsafe condition revealed on the Model 787 airplane. The 
unsafe condition on Model 787 airplanes has been addressed.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Service Bulletin 777-25-0617, dated June 6, 
2014. The service information describes procedures for replacing the 
water filter assembly in Jamco steam ovens, P/N ASN2001-1 and P/N 
ASN2001-12. This service information is reasonably available because 
the interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    We are issuing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

AD Requirements

    This AD requires accomplishing the actions specified in the service 
information described previously.

FAA's Justification and Determination of the Effective Date

    There are currently no domestic operators of this product. 
Therefore, we find that notice and opportunity for prior public comment 
are unnecessary and that good cause exists for making this amendment 
effective in less than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety and was not preceded by notice and an opportunity for public 
comment. However, we invite you to send any written data, views, or 
arguments about this final rule. Send your comments to an address 
listed under the ADDRESSES section. Include the docket number FAA-2018-
0507 and Product Identifier 2018-NM-027-AD at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this final rule. We will 
consider all comments received by the closing date and may amend this 
final rule because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this final rule.

Costs of Compliance

    Currently, there are no affected U.S.-registered airplanes. If an 
affected airplane is imported and placed on the U.S. Register in the 
future, we provide the following cost estimates to comply with this AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
             Action                      Labor cost          Parts cost               Cost per product
----------------------------------------------------------------------------------------------------------------
Replacement.....................  1 work-hour x $85 per                $0  $85 per steam oven.
                                   hour = $85 per steam
                                   oven.
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some or all of the costs of this AD 
may be covered under warranty, thereby reducing the cost impact on 
affected individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all known costs in our cost 
estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation Programs'' 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This AD is issued in accordance with authority delegated by the 
Executive Director, Aircraft Certification Service, as authorized by 
FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the Compliance and Airworthiness Division, but 
during this transition period, the Executive Director has delegated the 
authority to issue ADs applicable to transport category airplanes and 
associated appliances to the Director of the System Oversight Division.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

[[Page 26566]]

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2018-12-04 The Boeing Company: Amendment 39-19308 ; Docket No. FAA-
2018-0507; Product Identifier 2018-NM-027-AD.

(a) Effective Date

    This AD is effective June 25, 2018.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 777-300ER series 
airplanes, certificated in any category, as identified in Boeing 
Service Bulletin 777-25-0617, dated June 6, 2014.

(d) Subject

    Air Transport Association (ATA) of America Code 25, Equipment/
furnishings.

(e) Unsafe Condition

    This AD was prompted by a report that water can enter the steam 
oven cavity and become heated and then released when the oven door 
is opened. This condition, if not addressed, could result in injury 
to the cabincrew.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Replacement of Water Filter Assembly

    Within 375 days after the effective date of this AD: Replace the 
water filter assembly for Jamco steam ovens, part number (P/N) 
ASN2001-1 and P/N ASN2001-12, at the locations identified in, and in 
accordance with the Accomplishment Instructions of Boeing Service 
Bulletin 777-25-0617, dated June 6, 2014.

    Note 1 to paragraph (g) of this AD: Boeing Service Bulletin 777-
25-0617, dated June 6, 2014, refers to Jamco Service Bulletin 
ASN2001-25-3118, Revision 1, dated June 5, 2014, as an additional 
source of information for replacement of the water filter assembly.

(h) Parts Installation Prohibition

    As of the effective date of this AD, no person may install on 
any airplane, a Jamco steam oven having P/N ASN2001-1 or P/N 
ASN2001-12, unless the modification required by paragraph (g) of 
this AD is accomplished for that steam oven.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO Branch, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or local Flight Standards District 
Office, as appropriate. If sending information directly to the 
manager of the certification office, send it to the attention of the 
person identified in paragraph (j) of this AD. Information may be 
emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Seattle ACO Branch, to make those findings. To be approved, 
the repair method, modification deviation, or alteration deviation 
must meet the certification basis of the airplane, and the approval 
must specifically refer to this AD.

(j) Related Information

    For more information about this AD, contact Stanley Chen, 
Aerospace Engineer, Cabin Safety and Environmental Systems Section, 
FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; 
phone and fax: 206-231-3565; email: [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Boeing Service Bulletin 777-25-0617, dated June 6, 2014.
    (ii) Reserved.
    (3) For Boeing service information identified in this AD, 
contact Boeing Commercial Airplanes, Attention: Contractual & Data 
Services (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 
90740-5600; telephone 562-797-1717; internet https://www.myboeingfleet.com.
    (4) You may view this service information at the FAA, Transport 
Standards Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 
206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Des Moines, Washington, on May 29, 2018.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2018-12270 Filed 6-7-18; 8:45 am]
 BILLING CODE 4910-13-P


