[Federal Register Volume 83, Number 38 (Monday, February 26, 2018)]
[Proposed Rules]
[Pages 8199-8201]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2018-03712]


 ========================================================================
 Proposed Rules
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains notices to the public of 
 the proposed issuance of rules and regulations. The purpose of these 
 notices is to give interested persons an opportunity to participate in 
 the rule making prior to the adoption of the final rules.
 
 ========================================================================
 

  Federal Register / Vol. 83, No. 38 / Monday, February 26, 2018 / 
Proposed Rules  

[[Page 8199]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2018-0115; Product Identifier 2017-NM-110-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 777-200, -200LR, -300, and -300ER 
series airplanes. This proposed AD was prompted by reports that 
additional areas of Boeing Material Specification (BMS) 8-39 flexible 
urethane foam were found during a routine inspection. This proposed AD 
would require an inspection for foam insulation on the dripshield above 
the overhead panel support structure and replacement if necessary. For 
certain airplanes, this proposed AD would also require replacement of 
foam insulation on the overhead panel support structure. We are 
proposing this AD to address the unsafe condition on these products.

DATES: We must receive comments on this proposed AD by April 12, 2018.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; internet https://www.myboeingfleet.com. You may 
view this service information at the FAA, Transport Standards Branch, 
2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195. It is also 
available on the internet at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2018-0115.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
0115; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this NPRM, the regulatory evaluation, any comments received, 
and other information. The street address for the Docket Office (phone: 
800-647-5527) is in the ADDRESSES section. Comments will be available 
in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Scott Craig, Aerospace Engineer, Cabin 
Safety and Environmental Systems Section, FAA, Seattle ACO Branch, 2200 
South 216th Street, Des Moines, WA 98198; phone and fax: 206-231-3566; 
email: [email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2018-0115; 
Product Identifier 2017-NM-110-AD'' at the beginning of your comments. 
We specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this NPRM. We will consider all 
comments received by the closing date and may amend this NPRM because 
of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this NPRM.

Discussion

    We have received reports indicating additional areas of BMS 8-39 
flexible urethane foam were found during the accomplishment of AD 2013-
11-04, Amendment 39-17464 (78 FR 33193, June 4, 2013) (``AD 2013-11-
04''). AD 2013-11-04 was prompted by operator or in-service reports of 
burned BMS 8-39 urethane foam, and a report from the airplane 
manufacturer indicating that airplanes were assembled, throughout 
various areas of the airplane (including flight deck and cargo 
compartments), with seals made of BMS 8-39 urethane foam, a material 
with fire-retardant properties that deteriorate with age. AD 2013-11-04 
requires replacing certain seals made of BMS 8-39 urethane foam.
    BMS 8-39 urethane foam fire retardants are mixed into, but are not 
chemically connected with, the remaining components of the foam. Over 
time, this condition will cause the fire retardant properties to have 
decreased effectiveness. The concern is hidden areas where fire cannot 
easily be detected and suppressed. Aged BMS 8-39 foam exposed to an 
ignition source provides a potential fuel source for fire propagation. 
The degradation of the foam increases the potential for an uncontrolled 
fire below the passenger compartment floor and other locations outside 
the areas covered by smoke detection and fire protection systems. This 
condition, if not corrected, could result in loss of control of the 
airplane during a fire.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Special Attention Service Bulletin 777-25-0621, 
Revision 1, dated August 4, 2017. This service information describes 
procedures for a general visual inspection for foam insulation on the 
dripshield above the overhead panel support structure and replacement 
if necessary. This service information also describes procedures for 
replacement of foam insulation on the overhead panel support structure. 
This service information is reasonably available because the interested 
parties have access to it through their normal course

[[Page 8200]]

of business or by the means identified in the ADDRESSES section.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the Boeing Special Attention Service Bulletin 777-25-0621, Revision 
1, dated August 4, 2017, as described previously, except for any 
differences identified as exceptions in the regulatory text of this 
proposed AD. For information on the procedures and compliance times, 
see this service information at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2018-0115.

Costs of Compliance

    We estimate that this proposed AD affects 132 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                                                     Estimated Costs
--------------------------------------------------------------------------------------------------------------------------------------------------------
                Action                          Labor cost          Parts cost            Cost per product                  Cost on U.S. operators
--------------------------------------------------------------------------------------------------------------------------------------------------------
Inspection and replacement of foam      Up to 32 work-hours x $85       $5,611  Up to $8,331.......................  Up to $1,099,692.
 insulation.                             per hour = $2,720.
--------------------------------------------------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes to the Director of the System Oversight 
Division.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2018-0115; Product Identifier 
2017-NM-110-AD.

(a) Comments Due Date

    We must receive comments by April 12, 2018.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 777-200, -200LR, -
300, and -300ER series airplanes, certificated in any category, as 
identified in Boeing Special Attention Service Bulletin 777-25-0621, 
Revision 1, dated August 4, 2017.

(d) Subject

    Air Transport Association (ATA) of America Code 25, Equipment/
furnishings.

(e) Unsafe Condition

    This AD was prompted by reports that additional areas of Boeing 
Material Specification (BMS) 8-39 flexible urethane foam were found 
during a routine inspection pursuant to a previously issued AD. The 
degradation of the foam over time increases the potential for an 
uncontrolled fire below the passenger compartment floor and other 
locations outside the areas covered by smoke detection and fire 
protection systems. We are issuing this AD to address BMS 8-39 
flexible urethane foam found in certain areas of an airplane, which, 
if exposed to an ignition source, could cause loss of control of the 
airplane during a fire.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection and Replacement of Foam Installation

    Except as required by paragraph (h) of this AD: At the 
applicable times specified in paragraph 1.E., ``Compliance,'' of 
Boeing Special Attention Service Bulletin 777-25-0621, Revision 1, 
dated August 4, 2017, do all applicable actions identified as ``RC'' 
(required for compliance) in, and in accordance with, the 
Accomplishment Instructions of Boeing Special Attention Service 
Bulletin 777-25-0621, Revision 1, dated August 4, 2017.

(h) Exception to Service Information Specifications

    For purposes of determining compliance with the requirements of 
this AD: Where Boeing Special Attention Service Bulletin 777-25-
0621, Revision 1, dated August 4, 2017, uses the phrase ``the 
original issue date

[[Page 8201]]

of this service bulletin,'' this AD requires using ``the effective 
date of this AD.''

(i) Credit for Previous Actions

    This paragraph provides credit for the corresponding actions 
specified in paragraph (g) of this AD, if those actions were 
performed before the effective date of this AD using Boeing Special 
Attention Service Bulletin 777-25-0621, dated December 10, 2014.

(j) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO Branch, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or local Flight Standards District 
Office, as appropriate. If sending information directly to the 
manager of the certification office, send it to the attention of the 
person identified in paragraph (k)(1) of this AD. Information may be 
emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Seattle ACO Branch, to make those findings. To be approved, 
the repair method, modification deviation, or alteration deviation 
must meet the certification basis of the airplane, and the approval 
must specifically refer to this AD.
    (4) For service information that contains steps that are labeled 
as RC, the provisions of paragraphs (j)(4)(i) and (j)(4)(ii) of this 
AD apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. If a step or substep is labeled ``RC Exempt,'' then the 
RC requirement is removed from that step or substep. An AMOC is 
required for any deviations to RC steps, including substeps and 
identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(k) Related Information

    (1) For more information about this AD, contact Scott Craig, 
Aerospace Engineer, Cabin Safety and Environmental Systems Section, 
FAA, Seattle ACO Branch, 2200 South 216th Street, Des Moines, WA 
98198; phone and fax: 206-231-3566; email: [email protected].
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; internet https://www.myboeingfleet.com. You may view this service information at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, 
WA. For information on the availability of this material at the FAA, 
call 206-231-3195.

    Issued in Renton, Washington, on February 15, 2018.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2018-03712 Filed 2-23-18; 8:45 am]
 BILLING CODE 4910-13-P


