
[Federal Register Volume 82, Number 122 (Tuesday, June 27, 2017)]
[Proposed Rules]
[Pages 29014-29016]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2017-13364]


 ========================================================================
 Proposed Rules
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains notices to the public of 
 the proposed issuance of rules and regulations. The purpose of these 
 notices is to give interested persons an opportunity to participate in 
 the rule making prior to the adoption of the final rules.
 
 ========================================================================
 

  Federal Register / Vol. 82, No. 122 / Tuesday, June 27, 2017 / 
Proposed Rules  

[[Page 29014]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2017-0626; Directorate Identifier 2016-NM-210-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc., Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new Airworthiness Directive (AD), for 
certain Bombardier, Inc., Model CL-600-2B16 (CL-604 Variant) airplanes. 
This proposed AD was prompted by reports of in-flight uncommanded 
rudder movements. This proposed AD would require modification of the 
wiring for the yaw damper control system. We are proposing this AD to 
address the unsafe condition on these products.

DATES: We must receive comments on this proposed AD by August 11, 2017.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact 
Bombardier, Inc., 400 C[ocirc]te Vertu Road West, Dorval, Qu[eacute]bec 
H4S 1Y9, Canada; Widebody Customer Response Center North America toll-
free telephone 1-866-538-1247 or direct-dial telephone 1-514-855-2999; 
fax 514-855-7401; email ac.yul@aero.bombardier.com; Internet http://www.bombardier.com. You may view this referenced service information at 
the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, 
WA. For information on the availability of this material at the FAA, 
call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2017-
0626; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Cesar Gomez, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone 516-228-7318; fax 516-794-5531.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2017-0626; 
Directorate Identifier 2016-NM-210-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2016-38, effective December 12, 2016 (referred to after this as the 
Mandatory Continuing Airworthiness Information, or ``the MCAI''), to 
correct an unsafe condition for certain Bombardier, Inc., Model CL-600-
2B16 (CL-604 Variant) airplanes. The MCAI states:

    The [Canadian] AD CF-2013-22 [which corresponds to FAA AD 2014-
16-06, Amendment 39-17930 (79 FR 48972, August 19, 2014)] was issued 
on 12 August 2013 to mandate the introduction of an emergency 
procedure to the Aeroplane Flight Manual to address the uncommanded 
rudder movement.
    Since the original issue of [Canadian] AD CF-2013-22, Bombardier 
Aerospace has developed a wiring modification for the yaw damper 
control system to prevent uncommanded movement of the rudder.
    This [Canadian] AD mandates the incorporation of Service 
Bulletins (SB) 604-22-007 and 605-22-002 * * * *.

    This proposed AD would require modification of the wiring for the 
yaw damper control system. You may examine the MCAI in the AD docket on 
the Internet at http://www.regulations.gov by searching for and 
locating Docket No. FAA-2017-0626.

Related Service Information Under 1 CFR Part 51

    Bombardier, Inc., issued Service Bulletin 604-22-007, Revision 01, 
dated July 25, 2016; and Service Bulletin 605-22-002, Revision 01, 
dated July 25, 2016. The service information describes procedures for 
modifying the wiring harness for the yaw damper control system. These 
documents are distinct since they apply to different airplane 
configurations. This service information is reasonably available 
because the interested parties have access to it through their normal 
course of business or by the means identified in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified

[[Page 29015]]

of the unsafe condition described in the MCAI and service information 
referenced above. We are proposing this AD because we evaluated all 
pertinent information and determined an unsafe condition exists and is 
likely to exist or develop on other products of the same type design.

Costs of Compliance

    We estimate that this proposed AD affects 120 airplanes of U.S. 
registry.
    We estimate the following costs to comply with this proposed AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
            Action                  Labor cost         Parts cost      Cost per product   Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Modification..................  50 work-hours x    Up to $478.......  Up to $4,728......  Up to $567,360
                                 $85 per hour =
                                 $4,250.
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some of the costs of this proposed 
AD may be covered under warranty, thereby reducing the cost impact on 
affected individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new Airworthiness 
Directive (AD):

Bombardier, Inc.: Docket No. FAA-2017-0626; Directorate Identifier 
2016-NM-210-AD.

(a) Comments Due Date

    We must receive comments by August 10, 2017.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc., Model CL-600-2B16 (CL-604 
Variant) airplanes, certificated in any category, serial numbers (S/
Ns) 5301 through 5665 inclusive, 5701 through 5911 inclusive, 5913, 
and 5914.

(d) Subject

    Air Transport Association (ATA) of America Code 22, Autopilot 
System.

(e) Reason

    This AD was prompted by reports of in-flight uncommanded rudder 
movements. We are issuing this AD to prevent in-flight uncommanded 
rudder movements, which could lead to structural failure and 
subsequent loss of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Modification

    Within 48 months after the effective date of this AD: Modify the 
wiring harness for the yaw damper control system, in accordance with 
the Accomplishment Instructions of the applicable service 
information identified in paragraphs (g)(1) and (g)(2) of this AD.
    (1) For airplanes having S/Ns 5301 through 5665 inclusive: 
Bombardier Service Bulletin 604-22-007, Revision 01, dated July 25, 
2016.
    (2) For airplanes having S/Ns 5701 through 5911 inclusive, 5913, 
and 5914: Bombardier Service Bulletin 605-22-002, Revision 01, dated 
July 25, 2016.

(h) Part Installation Limitation

    As of the effective date of this AD, no person may install on 
any airplane a yaw damper actuator having part number 622-9968-002, 
unless the modification required by paragraph (g) of this AD has 
been accomplished.

(i) Credit for Previous Actions

    This paragraph provides credit for the modification required by 
paragraph (g) of this AD, if the modification was performed before 
the effective date of this AD using the applicable service 
information identified in paragraph (i)(1) or (i)(2) of this AD.
    (1) Bombardier Service Bulletin 604-22-007, dated June 23, 2015.
    (2) Bombardier Service Bulletin 605-22-002, dated June 23, 2015.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the manager of the ACO, send it to ATTN: The Program 
Manager, Continuing Operational Safety, FAA, New York ACO, 1600 
Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-
7300; fax 516-794-5531. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector,

[[Page 29016]]

the manager of the local flight standards district office/
certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO, 
ANE-170, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier, Inc.,'s TCCA Design Approval Organization (DAO). If 
approved by the DAO, the approval must include the DAO-authorized 
signature.

(k) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian Airworthiness Directive CF-2016-38, dated December 
12, 2016, for related information. This MCAI may be found in the AD 
docket on the Internet at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2017-0626.
    (2) For more information about this AD, contact Cesar Gomez, 
Aerospace Engineer, Airframe and Mechanical Systems Branch, ANE-171, 
FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, 
Suite 410, Westbury, NY 11590; telephone 516-228-7318; fax 516-794-
5531.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., Q-Series Technical Help Desk, 123 Garratt 
Boulevard, Toronto, Ontario M3K 1Y5, Canada; telephone 416-375-4000; 
fax 416-375-4539; email thd.qseries@aero.bombardier.com; Internet 
http://www.bombardier.com. You may view this service information at 
the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., 
Renton, WA. For information on the availability of this material at 
the FAA, call 425-227-1221.

    Issued in Renton, Washington, on June 19, 2017.
John P. Piccola, Jr.,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2017-13364 Filed 6-26-17; 8:45 am]
 BILLING CODE 4910-13-P


