
[Federal Register Volume 82, Number 146 (Tuesday, August 1, 2017)]
[Rules and Regulations]
[Pages 35628-35630]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2017-15477]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2017-0330; Directorate Identifier 2017-NM-016-AD; 
Amendment 39-18972; AD 2017-15-12]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
The Boeing Company Model 737-300, -400, and -500 series airplanes. This 
AD was prompted by an evaluation by the design approval holder (DAH) 
indicating that the lower skin at the skin lap splice lower fastener 
row is subject to widespread fatigue damage (WFD). This AD requires 
repetitive inspections for cracking in the skin lap splice at the lower 
fastener row, and repair if necessary. We are issuing this AD to 
address the unsafe condition on these products.

DATES: This AD is effective September 5, 2017.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of September 5, 
2017.

ADDRESSES: For service information identified in this final rule, 
contact Boeing Commercial Airplanes, Attention: Contractual & Data 
Services (C&DS), 2600 Westminster Blvd., MC 110 SK57, Seal Beach, CA 
90740-5600; telephone 562-797-1717; Internet https://www.myboeingfleet.com. You may view this referenced service information 
at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., 
Renton, WA. For information on the availability of this material at the 
FAA, call 425-227-1221. Boeing Alert Service Bulletin 737-53A1365, 
dated January 23, 2017, is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2017-
0330.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2017-
0330; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this final rule, the regulatory evaluation, any comments 
received, and other information. The address for the Docket Office 
(phone: 800-647-5527) is Docket Management Facility, U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: James Guo, Aerospace Engineer, 
Airframe Branch, ANM-120L, FAA, Los Angeles Aircraft Certification 
Office (ACO), 3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 
562-627-5357; fax: 562-627-5210; email: james.guo@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to certain The Boeing Company 
Model 737-300, -400, and -500 series airplanes. The NPRM published in 
the

[[Page 35629]]

Federal Register on May 1, 2017 (82 FR 20288). The NPRM was prompted by 
an evaluation by the DAH indicating that the lower skin at the skin lap 
splice lower fastener row is subject to WFD. The NPRM proposed to 
require repetitive inspections for cracking in the skin lap splice at 
the lower fastener row, and repair if necessary.

Comments

    We gave the public the opportunity to participate in developing 
this AD. The following presents the comments received on the NPRM and 
the FAA's response to each comment.

Supportive Comment

    Boeing stated that it concurred with the NPRM.

Effect of Winglets on Accomplishment of the Proposed Actions

    Aviation Partners Boeing stated that accomplishing the supplemental 
type certificate (STC) ST01219SE does not affect the actions specified 
in the NPRM.
    We concur with the request. We have redesignated paragraph (c) of 
the proposed AD as paragraph (c)(1) of this AD and added paragraph 
(c)(2) to this AD to state that installation of STC ST01219SE does not 
affect the ability to accomplish the actions required by this AD. 
Therefore, for airplanes on which STC ST01219SE is installed, a 
``change in product'' alternative method of compliance (AMOC) approval 
request is not necessary to comply with the requirements of 14 CFR 
39.17.

Conclusion

    We reviewed the relevant data, considered the comments received, 
and determined that air safety and the public interest require adopting 
this final rule with the change described previously and minor 
editorial changes. We have determined that these minor changes:
     Are consistent with the intent that was proposed in the 
NPRM for correcting the unsafe condition; and
     Do not add any additional burden upon the public than was 
already proposed in NPRM.
    We also determined that these changes will not increase the 
economic burden on any operator or increase the scope of this final 
rule.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Alert Service Bulletin 737-53A1365, dated 
January 23, 2017. The service information describes procedures for eddy 
current inspections for cracking at the skin lap splice in the lower 
fastener row, and repair if necessary. This service information is 
reasonably available because the interested parties have access to it 
through their normal course of business or by the means identified in 
the ADDRESSES section.

Costs of Compliance

    We estimate that this AD affects 126 airplanes of U.S. registry. We 
estimate the following costs to comply with this AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                Cost on U.S.
           Action                  Labor cost         Parts cost       Cost per product          operators
----------------------------------------------------------------------------------------------------------------
Inspection.................  84 work-hours x $85                $0  $7,140 per inspection  $899,640 per
                              per hour = $7,140                      cycle.                 inspection cycle.
                              per inspection cycle.
----------------------------------------------------------------------------------------------------------------

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2017-15-12 The Boeing Company: Amendment 39-18972; Docket No. FAA-
2017-0330; Directorate Identifier 2017-NM-016-AD.

(a) Effective Date

    This AD is effective September 5, 2017.

(b) Affected ADs

    None.

(c) Applicability

    (1) This AD applies to The Boeing Company Model 737-300, -400, 
and -500 series airplanes, certificated in any category,

[[Page 35630]]

as identified in Boeing Alert Service Bulletin 737-53A1365, dated 
January 23, 2017.
    (2) Installation of Supplemental Type Certificate (STC) 
ST01219SE (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/EBD1CEC7B301293E86257CB30045557A?OpenDocument&Highlight=st01219se) 
does not affect the ability to accomplish the actions required by 
this AD. Therefore, for airplanes on which STC ST01219SE is 
installed, a ``change in product'' alternative method of compliance 
(AMOC) approval request is not necessary to comply with the 
requirements of 14 CFR 39.17.

(d) Subject

    Air Transport Association (ATA) of America Code 53; Fuselage.

(e) Unsafe Condition

    This AD was prompted by an evaluation by the design approval 
holder indicating that the lower skin at the skin lap splice lower 
fastener row is subject to widespread fatigue damage. We are issuing 
this AD to detect and correct cracks in the lower skin, which, if 
not detected, could link up, resulting in reduced structural 
integrity of the airplane and consequent uncontrolled decompression 
of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Repetitive Inspections

    Except as provided by paragraph (i) of this AD, at the 
applicable time specified in paragraph 1.E., ``Compliance,'' of 
Boeing Alert Service Bulletin 737-53A1365, dated January 23, 2017: 
Do external eddy current inspections at stringer S-14 on the left 
and right sides of the airplane (S-14L and S-14R) for any crack in 
the skin lap splice at the lower fastener row, in accordance with 
the Accomplishment Instructions of Boeing Alert Service Bulletin 
737-53A1365, dated January 23, 2017. Repeat the inspections 
thereafter at the applicable times specified in paragraph 1.E., 
``Compliance,'' of Boeing Alert Service Bulletin 737-53A1365, dated 
January 23, 2017.

(h) Repair

    If any crack is found during any inspection required by 
paragraph (g) of this AD, repair before further flight using a 
method approved in accordance with the procedures specified in 
paragraph (j) of this AD. Although Boeing Alert Service Bulletin 
737-53A1365, dated January 23, 2017, specifies to contact Boeing for 
appropriate action and specifies that action as ``RC'' (Required for 
Compliance), this AD requires repair as specified in this paragraph.

(i) Exceptions to Service Information Specifications

    (1) Where Boeing Alert Service Bulletin 737-53A1365, dated 
January 23, 2017, specifies a compliance time ``after the original 
issue date of this service bulletin,'' this AD requires compliance 
within the specified compliance time after the effective date of 
this AD.
    (2) The Condition column of Table 1 and Table 2 of paragraph 
1.E., ``Compliance,'' of Boeing Alert Service Bulletin 737-53A1365, 
dated January 23, 2017, refers to total flight cycles ``at the 
original issue date of this service bulletin.'' This AD, however, 
applies to the airplanes with the specified total flight cycles as 
of the effective date of this AD.

(j) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Los Angeles Aircraft Certification Office 
(ACO), FAA, has the authority to approve AMOCs for this AD, if 
requested using the procedures found in 14 CFR 39.19. In accordance 
with 14 CFR 39.19, send your request to your principal inspector or 
local Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in paragraph (k) of this AD. 
Information may be emailed to: 9-ANM-LAACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Los Angeles ACO, to make those findings. To be approved, 
the repair method, modification deviation, or alteration deviation 
must meet the certification basis of the airplane, and the approval 
must specifically refer to this AD.
    (4) Except as required by paragraph (h) of this AD: For service 
information that contains steps that are labeled as Required for 
Compliance (RC), the provisions of paragraphs (j)(4)(i) and 
(j)(4)(ii) of this AD apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. If a step or substep is labeled ``RC Exempt,'' then the 
RC requirement is removed from that step or substep. An AMOC is 
required for any deviations to RC steps, including substeps and 
identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(k) Related Information

    For more information about this AD, contact James Guo, Aerospace 
Engineer, Airframe Branch, ANM-120L, FAA, Los Angeles ACO, 3960 
Paramount Boulevard, Lakewood, CA 90712-4137; phone: 562-627-5357; 
fax: 562-627-5210; email: james.guo@faa.gov.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Boeing Alert Service Bulletin 737-53A1365, dated January 23, 
2017.
    (ii) Reserved.
    (3) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; Internet https://www.myboeingfleet.com.
    (4) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on July 14, 2017.
Dionne Palermo,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2017-15477 Filed 7-31-17; 8:45 am]
 BILLING CODE 4910-13-P


