
[Federal Register Volume 81, Number 222 (Thursday, November 17, 2016)]
[Proposed Rules]
[Pages 81021-81023]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-27310]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2016-9384; Directorate Identifier 2016-NM-154-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 777-300ER series airplanes. This 
proposed AD was prompted by a report that certain galley tripod mount 
assemblies were not connected to the tie rods in the overhead support 
structure. This proposed AD would require an inspection of certain 
galleys for the presence of the hardware that connects the tripod mount 
assembly to the tie rods in the overhead support structure, and 
corrective actions if necessary. We are proposing this AD to address 
the unsafe condition on these products.

DATES: We must receive comments on this proposed AD by January 3, 2017.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740; telephone 
562-797-1717; Internet https://www.myboeingfleet.com. You may view this 
referenced service information at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the 
availability of this material at the FAA, call 425-227-1221. It is also 
available on the internet at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2016-9384.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
9384; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Eric Brown, Aerospace Engineer, Cabin 
Safety and Environmental Systems Branch, ANM-150S, FAA, Seattle 
Aircraft Certification Office (ACO), 1601 Lind Avenue SW., Renton, WA 
98057-3356; phone: 425-917-6476; fax: 425-917-6590; email: 
eric.m.brown@faa.gov.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2016-9384; 
Directorate Identifier 2016-NM-154-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    We have received a report that the T53 and T52 tie rods to the 
tripod mount assembly in the A2 and A3 galleys were found unattached 
during a routine production inspection of certain airplanes before 
delivery. The cause was determined to be a change to the galley 
installation sequence. This changed installation sequence did not 
include a robust method to make sure that the tie rods were attached to 
the galley before delivery. Since this unsafe condition was found, 
Boeing has implemented a new improved process to ensure that the 
hardware that attaches the T53 and T52 tie rods to the tripod mount 
assembly in the A2 and A3 galleys is attached. A galley tripod mount 
assembly that is unconnected to the tie rods in the overhead support 
structure can cause a galley to come loose under a high dynamic load 
causing a risk of serious injury to passengers and the blocking of 
evacuation routes.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Alert Service Bulletin 777-25A0677, dated April 
25,

[[Page 81022]]

2016. The service information describes procedures for doing an 
inspection of the area above the A2 and A3 galleys to make sure the 
hardware (i.e., pin assembly or bolt assembly) that connects the tripod 
mount assembly to the applicable T53 and T52 tie rods is installed; and 
corrective actions. This service information is reasonably available 
because the interested parties have access to it through their normal 
course of business or by the means identified in the ADDRESSES section.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the service information described previously, except as discussed 
under ``Differences Between this Proposed AD and the Service 
Information.'' For information on the procedures and compliance times, 
see this service information at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2016-9384.
    The phrase ``corrective actions'' is used in this proposed AD. 
Corrective actions correct or address any condition found. Corrective 
actions in an AD could include, for example, repairs.

Differences Between This Proposed AD and the Service Information

    This proposed AD requires a detailed inspection for specific 
hardware instead of the general visual inspection specified in Boeing 
Alert Service Bulletin 777-25A0677, dated April 25, 2016.

Costs of Compliance

    We estimate that this proposed AD affects 4 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
               Action                         Labor cost            Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Inspection.........................  1 work-hour x $85 per hour               $0             $85            $340
                                      = $85.
----------------------------------------------------------------------------------------------------------------

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this proposed 
AD.
    According to the manufacturer, some of the costs of this proposed 
AD may be covered under warranty, thereby reducing the cost impact on 
affected individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all available costs in our 
cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

    The Boeing Company: Docket No. FAA-2016-9384; Directorate 
Identifier 2016-NM-154-AD.

(a) Comments Due Date

    We must receive comments by January 3, 2017.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 777-300ER series 
airplanes, certificated in any category, as identified in Boeing 
Alert Service Bulletin 777-25A0677, dated April 25, 2016.

(d) Subject

    Air Transport Association (ATA) of America Code 25, Equipment/
furnishings.

(e) Unsafe Condition

    This AD was prompted by a report that certain galley tripod 
mount assemblies were not attached to the tie rods in the overhead 
support structure. We are issuing this AD to detect and correct an 
unconnected galley tripod mount assembly to the tie rods in the 
overhead support structure, which can cause a galley to come loose 
under a high dynamic load causing a risk of serious injury to 
passengers and the blocking of evacuation routes.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

[[Page 81023]]

(g) Inspection and Corrective Actions

    Within 12 months after the effective date of this AD: Do a 
detailed inspection of the area above the A2 and A3 galleys to make 
sure the hardware (i.e., pin assembly or bolt assembly) that 
connects the tripod mount assembly to the applicable T53 and T52 tie 
rods is installed, and do all applicable corrective actions, in 
accordance with the Accomplishment Instructions of Boeing Alert 
Service Bulletin 777-25A0677, dated April 25, 2016. Do all 
applicable corrective actions before further flight.

(h) Definition of Detailed Inspection

    For the purposes of this AD, a detailed inspection is an 
intensive examination of a specific item, installation, or assembly 
to detect damage, failure, or irregularity. Available lighting is 
normally supplemented with a direct source of good lighting at an 
intensity deemed appropriate. Inspection aids such as mirror, 
magnifying lenses, etc., may be necessary. Surface cleaning and 
elaborate procedures may be required.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in paragraph (j)(1) of this AD. 
Information may be emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Seattle ACO, to make those findings. To be approved, the 
repair method, modification deviation, or alteration deviation must 
meet the certification basis of the airplane, and the approval must 
specifically refer to this AD.
    (4) For service information that contains steps that are labeled 
as Required for Compliance (RC), the provisions of paragraphs 
(i)(4)(i) and (i)(4)(ii) of this AD apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. If a step or substep is labeled ``RC Exempt,'' then the 
RC requirement is removed from that step or substep. An AMOC is 
required for any deviations to RC steps, including substeps and 
identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(j) Related Information

    (1) For more information about this AD, contact Eric Brown, 
Aerospace Engineer, Cabin Safety and Environmental Systems Branch, 
ANM-150S, FAA, Seattle Aircraft Certification Office (ACO), 1601 
Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6476; fax: 
425-917-6590; email: eric.m.brown@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740; 
telephone 562-797-1717; Internet https://www.myboeingfleet.com. You 
may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.

    Issued in Renton, Washington, on November 2, 2016.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2016-27310 Filed 11-16-16; 8:45 am]
 BILLING CODE 4910-13-P


