
[Federal Register Volume 81, Number 69 (Monday, April 11, 2016)]
[Rules and Regulations]
[Pages 21253-21255]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-07842]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2016-5458; Directorate Identifier 2016-NM-027-AD; 
Amendment 39-18473; AD 2016-07-28]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for all The 
Boeing Company Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), 
and DC-9-87 (MD-87) airplanes, and Model MD-88 airplanes. This AD 
requires repetitive eddy current high frequency (ETHF) inspections for 
any cracking in the left and right side center wing lower skin, and 
corrective actions if necessary. This AD was prompted by reports of 
cracking at certain stringers, associated end fittings, and skins in 
the center wing fuel tank where the stringers meet the end fittings. We 
are issuing this AD to detect and correct cracking in the center wing 
lower skin. Such cracking could cause structural failure of the wings.

DATES: This AD is effective April 26, 2016.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of April 26, 
2016.
    We must receive comments on this AD by May 26, 2016.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For service information identified in this final rule, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
3855 Lakewood Boulevard, MC D800-0019, Long Beach, CA 90846-0001; 
telephone 206-544-5000, extension 2; fax 206-766-5683; Internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221. It is also available on the 
Internet at http://www.regulations.gov by searching for and locating 
Docket No. FAA-2016-5458.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
5458; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this AD, the regulatory evaluation, any comments received, and 
other information. The street address for the Docket Office (phone: 
800-647-5527) is in the ADDRESSES section. Comments will be available 
in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Haytham Alaidy, Aerospace Engineer, 
Airframe Branch, ANM-120L, FAA, Los Angeles Aircraft Certification 
Office (ACO), 3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 
562-627-5224; fax: 562-627-5210; email: haytham.alaidy@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

    We have received reports of cracks at stringers S-15, S-16, or S-
17, associated end fittings, and skins in the center wing fuel tank 
where the stringers meet the end fittings near Xcw=13 and Xcw=15. If 
stringer S-15, S-16, or S-17 is cracked in this area and there is a 
crack in the skin adjacent to the stringer crack, the skin crack could 
grow to a critical length before it can be found by routine maintenance 
inspections. This condition, if not corrected, could result in 
structural failure of the wings. We are issuing this AD to correct the 
unsafe condition on these products.

[[Page 21254]]

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Alert Service Bulletin MD80-57A244, dated March 
3, 2016. The service information describes procedures for repetitive 
ETHF inspections for any cracking in the left and right side center 
wing lower skin, and corrective actions. This service information is 
reasonably available because the interested parties have access to it 
through their normal course of business or by the means identified in 
the ADDRESSES section.

FAA's Determination

    We are issuing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of these same type 
designs.

AD Requirements

    This AD requires accomplishing the actions specified in the service 
information described previously, except as discussed under 
``Differences Between this AD and the Service Information. For 
information on the procedures and compliance times, see this service 
information at http://www.regulations.gov by searching for and locating 
Docket No. FAA-2016-5458.
    The phrase ``corrective actions'' is used in this AD. Corrective 
actions correct or address any condition found. Corrective actions in 
an AD could include, for example, repairs.

Differences Between This AD and the Service Information

    Boeing Alert Service Bulletin MD80-57A244, dated March 3, 2016, 
specifies to contact the manufacturer for certain instructions, but 
this AD requires accomplishment of repair methods, modification 
deviations, and alteration deviations in one of the following ways:
     In accordance with a method that we approve; or
     Using data that meet the certification basis of the 
airplane, and that have been approved by the Boeing Commercial 
Airplanes Organization Designation Authorization (ODA) whom we have 
authorized to make those findings.

FAA's Justification and Determination of the Effective Date

    An unsafe condition exists that requires the immediate adoption of 
this AD. The FAA has found that the risk to the flying public justifies 
waiving notice and comment prior to adoption of this rule because we 
have received reports indicating cracking at certain stringers, 
associated end fittings, and skins in the center wing fuel tank where 
the stringers meet the end fittings. This condition, if not corrected, 
could cause structural failure of the wings.
    Therefore, we find that notice and opportunity for prior public 
comment are impracticable and that good cause exists for making this 
amendment effective in less than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety and was not preceded by notice and an opportunity for public 
comment. However, we invite you to send any written data, views, or 
arguments about this AD. Send your comments to an address listed under 
the ADDRESSES section. Include the docket number FAA-2016-5458 and 
Directorate Identifier 2016-NM-027-AD at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this AD. We will 
consider all comments received by the closing date and may amend this 
AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this AD.

Costs of Compliance

    We estimate that this AD affects 395 airplanes of U.S. registry. We 
estimate the following costs to comply with this AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                 Cost on U.S.
              Action                    Labor cost        Parts cost      Cost per product        operators
----------------------------------------------------------------------------------------------------------------
Inspection.......................  14 work-hours x $85              $0  $1,190 per           $470,050 per
                                    per hour = $1,190                    inspection cycle.    inspection cycle.
                                    per inspection
                                    cycle.
----------------------------------------------------------------------------------------------------------------

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation Programs'' 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

[[Page 21255]]

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2016-07-28 The Boeing Company: Amendment 39-18473; Docket No. FAA-
2016-5458; Directorate Identifier 2016-NM-027-AD.

(a) Effective Date

    This AD is effective April 26, 2016.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all The Boeing Company Model DC-9-81 (MD-81), 
DC-9-82 (MD-82), DC-9-83 (MD-83), and DC-9-87 (MD-87) airplanes, and 
Model MD-88 airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 57, Wings.

(e) Unsafe Condition

    This AD was prompted by reports of cracking at certain 
stringers, associated end fittings, and skins in the center wing 
fuel tank where the stringers meet the end fittings. We are issuing 
this AD to detect and correct cracking in the center wing lower 
skin. Such cracking could cause structural failure of the wings.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection

    Except as required by paragraph (h)(1) and (h)(2) of this AD, at 
the applicable time specified in paragraph 1.E., ``Compliance,'' of 
Boeing Alert Service Bulletin MD80-57A244, dated March 3, 2016: Do 
an eddy current high frequency (ETHF) inspection for any cracking in 
the left and right side center wing lower skin, and do all 
applicable corrective actions; except as required by paragraph 
(h)(3) of this AD. Do all applicable corrective actions before 
further flight. Repeat the inspection thereafter at the intervals 
specified in paragraph 1.E., ``Compliance,'' of Boeing Alert Service 
Bulletin MD80-57A244, dated March 3, 2016.

(h) Exception to the Service Information

    (1) Where Boeing Alert Service Bulletin MD80-57A244, dated March 
3, 2016, specifies a compliance time ``after the original issue date 
of this service bulletin,'' this AD requires compliance within the 
specified compliance time after the effective date of this AD.
    (2) The Condition column of paragraph 1.E., ``Compliance,'' of 
Boeing Alert Service Bulletin MD80-57A244, dated March 3, 2016, 
refers to total flight cycles ``as of the original issue date of 
this service bulletin.'' This AD, however, applies to the airplanes 
with the specified total flight cycles as of the effective date of 
this AD.
    (3) If any crack is found during any inspection required by this 
AD, and Boeing Alert Service Bulletin MD80-57A244, dated March 3, 
2016, specifies to contact Boeing for appropriate action, and 
specifies that action as ``RC'' (Required for Compliance): Before 
further flight, repair using a method approved in accordance with 
the procedures specified in paragraph (i) of this AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Los Angeles Aircraft Certification Office 
(ACO), FAA, has the authority to approve AMOCs for this AD, if 
requested using the procedures found in 14 CFR 39.19. In accordance 
with 14 CFR 39.19, send your request to your principal inspector or 
local Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in paragraph (j) of this AD. 
Information may be emailed to: 9-ANM-LAACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Los Angeles ACO, to make those findings. To be approved, 
the repair method, modification deviation, or alteration deviation 
must meet the certification basis of the airplane, and the approval 
must specifically refer to this AD.
    (4) Except as required by paragraph (h)(3) of this AD: For 
service information that contains steps that are labeled as Required 
for Compliance (RC), the provisions of paragraphs (i)(4)(i) and 
(i)(4)(ii) of this AD apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. An AMOC is required for any deviations to RC steps, 
including substeps and identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(j) Related Information

    For more information about this AD, contact Haytham Alaidy, 
Aerospace Engineer, Airframe Branch, ANM-120L, FAA, Los Angeles 
Aircraft Certification Office (ACO), 3960 Paramount Boulevard, 
Lakewood, CA 90712-4137; phone: 562-627-5224; fax: 562-627-5210; 
email: haytham.alaidy@faa.gov.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Boeing Alert Service Bulletin MD80-57A244, dated March 3, 
2016.
    (ii) Reserved.
    (3) For Boeing service information identified in this AD, 
contact Boeing Commercial Airplanes, Attention: Data & Services 
Management, 3855 Lakewood Boulevard, MC D800-0019, Long Beach, CA 
90846-0001; telephone 206-544-5000, extension 2; fax 206-766-5683; 
Internet https://www.myboeingfleet.com.
    (4) You may view this referenced service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. 
For information on the availability of this material at the FAA, 
call 425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on March 30, 2016.
Victor Wicklund,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2016-07842 Filed 4-8-16; 8:45 am]
 BILLING CODE 4910-13-P


