
[Federal Register Volume 81, Number 37 (Thursday, February 25, 2016)]
[Proposed Rules]
[Pages 9367-9370]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-03698]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2016-3703; Directorate Identifier 2015-NM-115-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

[[Page 9368]]


ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 767-200, -300, and -400ER series 
airplanes. This proposed AD was prompted by an evaluation by the design 
approval holder (DAH) indicating that the skin lap splice is subject to 
widespread fatigue damage (WFD). This proposed AD would require 
repetitive external detailed and surface high frequency eddy current 
(HFEC) inspections of the outer skin for cracking around fastener heads 
common to the inboard fastener row of the skin lap splice. We are 
proposing this AD to detect and correct fatigue cracking of the skin 
lap splice, which, if not detected, could grow and result in possible 
rapid decompression and reduced structural integrity of the airplane.

DATES: We must receive comments on this proposed AD by April 11, 2016.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Data & Services Management, P.O. Box 
3707, MC 2H-65, Seattle, WA 98124-2207; telephone: 206-544-5000, 
extension 1; fax: 206-766-5680; Internet https://www.myboeingfleet.com. 
You may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221. It 
is also available on the Internet at http://www.regulations.gov by 
searching for and locating Docket No. FAA-2016-3703.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
3703; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Wayne Lockett, Aerospace Engineer, 
Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office 
(ACO), 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-
6447; fax: 425-917-6590; email: wayne.lockett@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2016-3703; 
Directorate Identifier 2015-NM-115-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Structural fatigue damage is progressive. It begins as minute 
cracks, and those cracks grow under the action of repeated stresses. 
This can happen because of normal operational conditions and design 
attributes, or because of isolated situations or incidents such as 
material defects, poor fabrication quality, or corrosion pits, dings, 
or scratches. Fatigue damage can occur locally, in small areas or 
structural design details, or globally. Global fatigue damage is 
general degradation of large areas of structure with similar structural 
details and stress levels. Multiple-site damage is global damage that 
occurs in a large structural element such as a single rivet line of a 
lap splice joining two large skin panels. Global damage can also occur 
in multiple elements such as adjacent frames or stringers. Multiple-
site-damage and multiple-element-damage cracks are typically too small 
initially to be reliably detected with normal inspection methods. 
Without intervention, these cracks will grow, and eventually compromise 
the structural integrity of the airplane, in a condition known as WFD. 
As an airplane ages, WFD will likely occur, and will certainly occur if 
the airplane is operated long enough without any intervention.
    The FAA's WFD final rule (75 FR 69746, November 15, 2010) became 
effective on January 14, 2011. The WFD rule requires certain actions to 
prevent structural failure due to WFD throughout the operational life 
of certain existing transport category airplanes and all of these 
airplanes that will be certificated in the future. For existing and 
future airplanes subject to the WFD rule, the rule requires that DAHs 
establish a limit of validity (LOV) of the engineering data that 
support the structural maintenance program. Operators affected by the 
WFD rule may not fly an airplane beyond its LOV, unless an extended LOV 
is approved.
    The WFD rule (75 FR 69746, November 15, 2010) does not require 
identifying and developing maintenance actions if the DAHs can show 
that such actions are not necessary to prevent WFD before the airplane 
reaches the LOV. Many LOVs, however, do depend on accomplishment of 
future maintenance actions. As stated in the WFD rule, any maintenance 
actions necessary to reach the LOV will be mandated by ADs through 
separate rulemaking actions.
    In the context of WFD, this action is necessary to enable DAHs to 
propose LOVs that allow operators the longest operational lives for 
their airplanes, and still ensure that WFD will not occur. This 
approach allows for an implementation strategy that provides 
flexibility to DAHs in determining the timing of service information 
development (with FAA approval), while providing operators with 
certainty regarding the LOV applicable to their airplanes.
    We have received an evaluation by the DAH indicating that the skin 
lap splice is subject to WFD. As a result of WFD analysis, the stringer 
S-2R skin lap splice from station (STA) 368 to STA 434 requires 
additional supplemental inspection beyond the inspections specified in 
the Boeing Model 767 airplane maintenance planning document. This 
condition, if not corrected, could result in cracking of the skin lap 
splice, which could grow and result in possible rapid

[[Page 9369]]

decompression and reduced structural integrity of the airplane.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Alert Service Bulletin 767-53A0260, dated August 
26, 2014. The service information describes procedures for a detailed 
inspection and a surface HFEC inspection at section 41, stringer S-2R 
skin lap splice from STA 368 to STA 434, for any cracking, and repair. 
This service information is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the service information described previously, except as discussed 
under ``Differences Between this Proposed AD and the Service 
Information.'' For information on the procedures and compliance times, 
see this service information at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2016-3703.''
    The phrase ``corrective actions'' is used in this proposed AD. 
``Corrective actions'' are actions that correct or address any 
condition found. Corrective actions in an AD could include, for 
example, repairs.

Costs of Compliance

    We estimate that this proposed AD affects 356 airplanes of U.S. 
registry.
    We estimate the following costs to comply with this proposed AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                 Cost on U.S.
              Action                    Labor cost        Parts cost     Cost per product         operators
----------------------------------------------------------------------------------------------------------------
Inspections......................  3 work-hours x $85             $0   $255 per inspection   $90,780 per
                                    per hour = $255 per                 cycle.                inspection cycle.
                                    inspection cycle.
----------------------------------------------------------------------------------------------------------------

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this proposed 
AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2016-3703; Directorate Identifier 
2015-NM-115-AD.

(a) Comments Due Date

    We must receive comments by April 11, 2016.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to the Boeing Company Model 767-200, -300, and -
400ER series airplanes, certificated in any category, as identified 
in Boeing Alert Service Bulletin 767-53A0260, dated August 26, 2014.

(d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Unsafe Condition

    This AD was prompted by an evaluation by the design approval 
holder indicating that the skin lap splice is subject to widespread 
fatigue damage. We are issuing this AD to detect and correct fatigue 
cracking of this skin lap splice, which, if not detected, could grow 
and result in possible rapid decompression and reduced structural 
integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection and Corrective Actions

    At the applicable time specified in paragraph 1.E., 
``Compliance,'' of Boeing Alert Service Bulletin 767-53A0260, dated 
August 26, 2014, except as required by paragraph (h) of this AD: Do 
a detailed inspection and a surface high frequency eddy current 
(HFEC) inspection at section 41, stringer S-2R skin lap splice from 
body station (STA) 368 to STA 434, for any cracking, and do all 
applicable corrective actions, in accordance with the Accomplishment 
Instructions of Boeing Alert

[[Page 9370]]

Service Bulletin 767-53A0260, dated August 26, 2014. Do all 
applicable corrective actions before further flight. Repeat the 
inspections thereafter at the applicable times specified in 
paragraph 1.E., ``Compliance,'' of Boeing Alert Service Bulletin 
767-53A0260, dated August 26, 2014. If any existing external repair 
is found in the inspection area, then the inspections in Part 1 of 
the Accomplishment Instructions of Boeing Alert Service Bulletin 
767-53A0260, dated August 26, 2014, are not required in the area 
hidden by the repair, provided that the repair was previously 
approved by the Manager, Seattle Aircraft Certification Office 
(ACO), or by the Authorized Representative of the Boeing Commercial 
Airplanes Organization Designation Authorization (ODA), or installed 
as specified in Part 2 of the Accomplishment Instructions of Boeing 
Alert Service Bulletin 767-53A0260, dated August 26, 2014. 
Inspections in Part 1 of the Accomplishment Instructions of Boeing 
Alert Service Bulletin 767-53A0260, dated August 26, 2014, remain 
applicable in areas not hidden by the repair.

(h) Exception to the Service Information

    Where Boeing Alert Service Bulletin 767-53A0260, dated August 
26, 2014, specifies a compliance time ``after the original issue 
date of this service bulletin,'' this AD requires compliance within 
the specified compliance time after the effective date of this AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or local Flight Standards District Office, as 
appropriate. If sending information directly to the manager of the 
ACO, send it to the attention of the person identified in paragraph 
(i) of this AD. Information may be emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes ODA that has 
been authorized by the Manager, Seattle ACO, to make those findings. 
To be approved, the repair method, modification deviation, or 
alteration deviation must meet the certification basis of the 
airplane, and the approval must specifically refer to this AD.
    (4) Except as required by paragraph (h) of this AD: For service 
information that contains steps that are labeled as Required for 
Compliance (RC), the provisions of paragraphs (i)(4)(i) and 
(i)(4)(ii) apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. An AMOC is required for any deviations to RC steps, 
including substeps and identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(j) Related Information

    (1) For more information about this AD, contact Wayne Lockett, 
Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle ACO, 
1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6447; 
fax: 425-917-6590; email: wayne.lockett@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone: 206-544-
5000, extension 1; fax: 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on February 15, 2016.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2016-03698 Filed 2-24-16; 8:45 am]
 BILLING CODE 4910-13-P


