
[Federal Register Volume 81, Number 1 (Monday, January 4, 2016)]
[Proposed Rules]
[Pages 24-27]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2015-32903]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2015-8135; Directorate Identifier 2015-NM-106-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

[[Page 25]]


ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 767-200, -300, and -400ER series 
airplanes. This proposed AD was prompted by multiple reports of un-
commanded escape slide inflation. This proposed AD would require 
modifying the regulator valves of the forward entry door, forward 
service door, aft entry door, and aft service door, and as applicable, 
modifying the regulator valves of the mid entry door and mid service 
door. We are proposing this AD to prevent out-of-tolerance trigger 
mechanism components (sector and sear) in the regulator valves, which 
can produce insufficient trigger engagement and reduced pull force 
values, possibly leading to un-commanded deployment of the slide during 
normal airplane maintenance or operation, and could result in injury to 
passengers and crew, damage to equipment, and the slide becoming 
unusable in an emergency evacuation.

DATES: We must receive comments on this proposed AD by February 18, 
2016.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone: 206-544-
5000, extension 1; fax: 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service information 
at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., 
Renton, WA 98057-3356. For information on the availability of this 
material at the FAA, call 425-227-1221. It is also available on the 
Internet at http://www.regulations.gov by searching for and locating 
Docket No. FAA-2015-8135.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
8135; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Kimberly DeVoe, Aerospace Engineer, 
Cabin Safety and Environmental Systems Branch, ANM-150S, FAA, 1601 Lind 
Avenue SW., Renton, WA 98057-3356; phone: 425-917-6495; fax: 425-917-
6590; email: Kimberly.DeVoe@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2015-8135; 
Directorate Identifier 2015-NM-106-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    We received reports of two incidents of un-commanded escape slide 
inflation. In both cases, out-of-tolerance trigger mechanism components 
(sector and sear) were found in the regulator valves which produced 
insufficient trigger engagement and reduced pull force values. This 
condition, if not corrected, could result in possible un-commanded 
deployment of the slide during normal airplane maintenance or operation 
and could result in injury to passengers and crew, damage to equipment, 
and the slide becoming unusable in an emergency evacuation.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Service Bulletin 767-25-0548, Revision 1, dated 
April 23, 2015. The service information describes procedures for 
modifying the regulator valves of the forward entry door, forward 
service door, aft entry door, aft service door, mid entry door and mid 
service door. The modification includes replacing the existing trigger 
mechanism sector and sear of the regulator valve with new trigger 
mechanism sector and sear. This service information is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in the 
ADDRESSES section of this NPRM.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the service information identified previously. For information on 
the procedures and compliance times, see this service information at 
http://www.regulations.gov by searching for and locating Docket No. 
FAA-2015-8135.

Explanation of ``RC'' Steps in Service Information

    The FAA worked in conjunction with industry, under the 
Airworthiness Directive Implementation Aviation Rulemaking Committee 
(ARC), to enhance the AD system. One enhancement was a new process for 
annotating which steps in the service information are required for 
compliance with an AD. Differentiating these steps from other tasks in 
the service information is expected to improve an owner's/operator's 
understanding of crucial AD requirements and help provide consistent 
judgment in AD compliance. The steps identified as Required for 
Compliance (RC) in any service information identified previously have a 
direct effect on detecting, preventing, resolving, or eliminating an 
identified unsafe condition.
    For service information that contains steps that are labeled as RC, 
the following provisions apply: (1) The steps labeled as RC, including 
substeps under an RC step and any figures identified in an RC step, 
must be done to comply with the AD, and an AMOC

[[Page 26]]

is required for any deviations to RC steps, including substeps and 
identified figures; and (2) steps not labeled as RC may be deviated 
from using accepted methods in accordance with the operator's 
maintenance or inspection program without obtaining approval of an 
AMOC, provided the RC steps, including substeps and identified figures, 
can still be done as specified, and the airplane can be put back in an 
airworthy condition.

Costs of Compliance

    We estimate that this proposed AD affects 302 airplanes of U.S. 
registry.
    We estimate the following costs to comply with this proposed AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
                Action                         Labor cost           Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Replacement of trigger mechanism        15 work-hours x $85 per           $2,236          $3,511      $1,060,322
 components--forward and aft entry/      hour = $1,275.
 service doors.
Replacement of trigger mechanism        8 work-hours x $85 per             1,118           1,798         542,996
 components--mid entry/service doors.    hour = $680.
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2015-8135; Directorate Identifier 
2015-NM-106-AD.

(a) Comments Due Date

    We must receive comments by February 18, 2016.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 767-200, -300, and -
400ER series airplanes, certificated in any category, as identified 
in Boeing Service Bulletin 767-25-0548, Revision 1, dated April 23, 
2015.

(d) Subject

    Air Transport Association (ATA) of America Code 25, Equipment/
furnishings.

(e) Unsafe Condition

    This AD was prompted by multiple reports of un-commanded escape 
slide inflation. We are issuing this AD to prevent out-of-tolerance 
trigger mechanism components (sector and sear) in the regulator 
valves, which can produce insufficient trigger engagement and 
reduced pull force values, possibly leading to un-commanded 
deployment of the slide during normal airplane maintenance or 
operation, and could result in injury to passengers and crew, damage 
to equipment, and the slide becoming unusable in an emergency 
evacuation.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Replacement of the Trigger Mechanism Sector and Sear

    Within 42 months after the effective date of this AD, modify the 
regulator valves of the forward entry door, forward service door, 
aft entry door, and aft service door, and as applicable, modify the 
regulator valves of the mid entry door and mid service door, in 
accordance with the Accomplishment Instructions of Boeing Service 
Bulletin 767-25-0548, Revision 1, dated April 23, 2015.

(h) Credit for Previous Actions

    This paragraph provides credit for the modification required by 
paragraph (g) of this AD, if the modification was performed before 
the effective date of this AD using Boeing Service Bulletin 767-25-
0548, dated November 5, 2014, which is not incorporated by reference 
in this AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in paragraph (j)(1) of this AD. 
Information may be emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair required by this AD if it is approved by the 
Boeing Commercial Airplanes Organization Designation Authorization 
(ODA) that has been authorized by the Manager, Seattle ACO, to make 
those findings. For a repair

[[Page 27]]

method to be approved, the repair must meet the certification basis 
of the airplane, and the approval must specifically refer to this 
AD.
    (4) For service information that contains steps that are labeled 
as Required for Compliance (RC), the provisions of paragraphs 
(i)(4)(i) and (i)(4)(ii) apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. An AMOC is required for any deviations to RC steps, 
including substeps and identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(j) Related Information

    (1) For more information about this AD, contact Kimberly DeVoe, 
Aerospace Engineer, Cabin Safety and Environmental Systems Branch, 
ANM-150S, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 
425-917-6495; fax: 425-917-6590; email: Kimberly.DeVoe@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone: 206-544-
5000, extension 1; fax: 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA 98057-3356. For information on the 
availability of this material at the FAA, call 425-227-1221.

    Issued in Renton, WA, on December 21, 2015.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2015-32903 Filed 12-31-15; 8:45 am]
 BILLING CODE 4910-13-P


