
[Federal Register Volume 80, Number 221 (Tuesday, November 17, 2015)]
[Proposed Rules]
[Pages 71745-71747]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2015-28882]


 ========================================================================
 Proposed Rules
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains notices to the public of 
 the proposed issuance of rules and regulations. The purpose of these 
 notices is to give interested persons an opportunity to participate in 
 the rule making prior to the adoption of the final rules.
 
 ========================================================================
 

  Federal Register / Vol. 80, No. 221 / Tuesday, November 17, 2015 / 
Proposed Rules  

[[Page 71745]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2015-4812; Directorate Identifier 2015-NM-034-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 787-8 airplanes. This proposed AD was 
prompted by a report that certain center and outboard stowage bin 
modules were incorrectly installed. This proposed AD would require an 
inspection of the center and outboard stowage bin modules for missing 
parts, quick release pins that are not fully engaged, and parts that 
are installed in incorrect locations; and corrective actions if 
necessary. We are proposing this AD to detect and correct incorrectly 
installed center and outboard stowage bin modules that might not remain 
intact during an emergency landing, resulting in injuries to occupants 
and interference with airplane evacuation.

DATES: We must receive comments on this proposed AD by January 4, 2016.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service information 
at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., 
Renton, WA. For information on the availability of this material at the 
FAA, call 425-227-1221. It is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
4812.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
4812; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Stanley Chen, Aerospace Engineer, 
Cabin Safety and Environmental Systems Branch, ANM-150S, FAA, Seattle 
Aircraft Certification Office (ACO), 1601 Lind Avenue SW., Renton, WA 
98057-3356; phone: 425-917- 6585; fax: 425-917-6590; email: 
stanley.chen@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2015-4812; 
Directorate Identifier 2015-NM-034-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    We received a report that certain center and outboard stowage bin 
modules were incorrectly installed on Model 787-8 airplanes. The 
affected stowage bin modules had parts that were missing or incorrectly 
installed and quick release pins that were not fully engaged. The 
missing and incorrectly installed parts included quick release pins, 
load transfer bars, tie rods, quick release pin retainers, radial 
struts, and splice fittings. Missing or incorrectly installed parts 
affect the load capability of a stowage bin, and during an emergency 
landing that stowage bin might not remain intact. We are proposing this 
AD to detect and correct incorrectly installed center and outboard 
stowage bin modules that might not remain intact during an emergency 
landing, resulting in injuries to occupants and interference with 
airplane evacuation.

Related Service Information Under 1 CFR Part 51

    We reviewed the following Boeing service information. This service 
information describes procedures for inspecting the installation of the 
center and outboard stowage bin modules and doing corrective actions.
     Boeing Alert Service Bulletin B787-81205-SB250036-00, 
Issue 001, dated September 10, 2013.
     Boeing Alert Service Bulletin B787-81205-SB250039-00, 
Issue 001, dated October 8, 2013.
     Boeing Alert Service Bulletin B787-81205-SB250040-00, 
Issue 001, dated October 14, 2013.
     Boeing Alert Service Bulletin B787-81205-SB250041-00, 
Issue 001, dated October 18, 2013.
     Boeing Alert Service Bulletin B787-81205-SB250042-00, 
Issue 001, dated October 28, 2013.
     Boeing Alert Service Bulletin B787-81205-SB250043-00, 
Issue 001, dated November 4, 2013.

[[Page 71746]]

     Boeing Alert Service Bulletin B787-81205-SB250044-00, 
Issue 001, dated November 8, 2013.
     Boeing Alert Service Bulletin B787-81205-SB250045-00, 
Issue 001, dated November 15, 2013.
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section of this 
NPRM.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the service information described previously. Refer to this service 
information for details on the procedures and compliance times.
    The phrase ``corrective actions'' might be used in this proposed 
AD. ``Corrective actions'' are actions that correct or address any 
condition found. Corrective actions in an AD could include, for 
example, repairs.

Costs of Compliance

    We estimate that this proposed AD affects 6 airplanes of U.S. 
registry.
    We estimate the following costs to comply with this proposed AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
              Action                        Labor cost            Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
Inspection........................  222 work-hours x $85 per               $0          $18,870         $113,220
                                     hour = $18,870.
----------------------------------------------------------------------------------------------------------------

    We estimate the following costs to do any necessary replacements 
that would be required based on the results of the proposed inspection. 
We have no way of determining the number of aircraft that might need 
these replacements.

                                               On-Condition Costs
----------------------------------------------------------------------------------------------------------------
              Action                       Labor cost                Parts cost             Cost per product
----------------------------------------------------------------------------------------------------------------
Replacement......................  20 work-hours x $85 per    Up to $21,191...........  Up to $22,891.
                                    hour = $1,700.
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, all of the costs of this proposed AD 
may be covered under warranty, thereby reducing the cost impact on 
affected individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2015-4812; Directorate Identifier 
2015-NM-034-AD.

(a) Comments Due Date

    We must receive comments by January 4, 2016.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to certain The Boeing Company Model 787-8 
airplanes, certificated in any category, identified in the service 
information specified in paragraphs (c)(1) through (c)(8) of this 
AD.
    (1) Boeing Alert Service Bulletin B787-81205-SB250036-00, Issue 
001, dated September 10, 2013.
    (2) Boeing Alert Service Bulletin B787-81205-SB250039-00, Issue 
001, dated October 8, 2013.

[[Page 71747]]

    (3) Boeing Alert Service Bulletin B787-81205-SB250040-00, Issue 
001, dated October 14, 2013.
    (4) Boeing Alert Service Bulletin B787-81205-SB250041-00, Issue 
001, dated October 18, 2013.
    (5) Boeing Alert Service Bulletin B787-81205-SB250042-00, Issue 
001, dated October 28, 2013.
    (6) Boeing Alert Service Bulletin B787-81205-SB250043-00, Issue 
001, dated November 4, 2013.
    (7) Boeing Alert Service Bulletin B787-81205-SB250044-00, Issue 
001, dated November 8, 2013.
    (8) Boeing Alert Service Bulletin B787-81205-SB250045-00, Issue 
001, dated November 15, 2013.

(d) Subject

    Air Transport Association (ATA) of America Code 25, Equipment/
Furnishings.

(e) Unsafe Condition

    This AD was prompted by a report that certain center and 
outboard stowage bin modules were incorrectly installed. We are 
issuing this AD to detect and correct incorrectly installed center 
and outboard stowage bin modules that might not remain intact during 
an emergency landing, resulting in injuries to occupants and 
interference with airplane evacuation.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection and Corrective Action

    Except as specified in paragraph (h) of this AD: At the 
applicable time specified in paragraph 5., ``Compliance,'' of the 
applicable service information specified in paragraphs (g)(1) 
through (g)(8) of this AD: Do a general visual inspection of the 
installations of the center and outboard stowage bin modules to 
determine if any part is missing, if any part is installed at an 
incorrect location, or if any quick release pin is not fully 
engaged; and do all applicable corrective actions; in accordance 
with the Accomplishment Instructions of the applicable service 
information identified in paragraphs (g)(1) through (g)(8) of this 
AD. Do all applicable corrective actions before further flight.
    (1) For airplanes having variable numbers (V/Ns) ZA177 through 
ZA183 inclusive: Use Boeing Alert Service Bulletin B787-81205-
SB250036-00, Issue 001, dated September 10, 2013.
    (2) For airplanes having V/Ns ZA100 through ZA105 inclusive, V/
Ns ZA116 through ZA119 inclusive, V/N ZA135, and V/NsZA506 through 
ZA511 inclusive: Use Boeing Alert Service Bulletin B787-81205-
SB250039-00, Issue 001, dated October 8, 2013.
    (3) For airplanes having V/Ns ZA460 through ZA464 inclusive: Use 
Boeing Alert Service Bulletin B787-81205-SB250040-00, Issue 001, 
dated October 14, 2013.
    (4) For airplanes having V/Ns ZA233 and V/Ns ZA236 through ZA240 
inclusive: Use Boeing Alert Service Bulletin B787-81205-SB250041-00, 
Issue 001, dated October 18, 2013.
    (5) For airplanes having V/Ns ZA285 through ZA290 inclusive: Use 
Boeing Alert Service Bulletin B787-81205-SB250042-00, Issue 001, 
dated October 28, 2013.
    (6) For airplanes having V/Ns ZA270 through ZA271 inclusive: Use 
Boeing Alert Service Bulletin B787-81205-SB250043-00, Issue 001, 
dated November 4, 2013.
    (7) For airplanes having V/Ns ZA261 through ZA264 inclusive: Use 
Boeing Alert Service Bulletin B787-81205-SB250044-00, Issue 001, 
dated November 8, 2013.
    (8) For airplanes having V/Ns ZA536 through ZA538 inclusive: Use 
Boeing Alert Service Bulletin B787-81205-SB250045-00, Issue 001, 
dated November 15, 2013.

(h) Exceptions to Service Information Specifications

    Where the service information identified in paragraphs (g)(1) 
through (g)(8) of this AD specifies a compliance time ``after the 
original issue date of this service bulletin,'' this AD requires 
compliance within the specified compliance time after the effective 
date of this AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in paragraph (j)(1) of this AD. 
Information may be emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Seattle ACO, to make those findings. To be approved, the 
repair method, modification deviation, or alteration deviation must 
meet the certification basis of the airplane and the approval must 
specifically refer to this AD.

(j) Related Information

    (1) For more information about this AD, contact Stanley Chen, 
Aerospace Engineer, Cabin Safety and Environmental Systems Branch, 
ANM-150S, FAA, Seattle ACO, 1601 Lind Avenue SW., Renton, WA 98057-
3356; phone: 425-917-6585; fax: 425-917-6590; email: 
stanley.chen@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. For information on the availability of this 
material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on November 4, 2015.
Dionne Palermo,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2015-28882 Filed 11-16-15; 8:45 am]
BILLING CODE 4910-13-P


